Summary of Contents for Christie TruLife+ Griffyn 4K32-RGB
Page 1
Technical Reference 020-103316-01 Christie TruLife+ Serial Commands...
Page 2
Christie's control such as maintenance of the product in proper working conditions. Performance specifications are based on information available at the time of printing. Christie makes no warranty of any kind with regard to this material, including, but not limited to, implied warranties of fitness for a particular purpose.
Page 3
Content Communicating with Christie TruLife+........6 Model names............6 Product documentation.
Page 6
Griffyn 4K32-RGB • Mirage 4K32-RGB Product documentation For installation, setup, and user information, see the product documentation available on the Christie website. Read all instructions before using or servicing this product. 1. Access the documentation from the Christie website: •...
Page 7
Once you have connected your computer to either the RS232 IN port (depending on which standard is supported by your computer) or to the Ethernet port on Christie TruLife+, you can remotely access controls and image setups, issue commands or queries, and receive replies.
Page 8
Ethernet is setup to obtain an IP address automatically if a DHCP server is on the network, modify IP settings, or manually enter an address. Christie recommends using the Ethernet port on the Video Input panel as the HDBaseT port is limited to 100 Mb/s.
Page 9
This function code appears immediately after the leading bracket that starts the message. In messages sent to Christie TruLife+ that do not have a subcode, a space between the function code and the first parameter (or special character) is optional.
Page 10
(PWR!000). Data The value for a given Christie TruLife+ state, such as on or off, appears in ASCII- decimal format directly after the request/reply symbol. You can add an optional space after the symbol—such as before the data—in a set message, but data in replies follow the exclamation mark (!) symbol without a space.
Page 12
The acknowledgment is returned after the message has been received and fully executed by Christie TruLife+ (such as in the case of a source switch it is not sent until the switch is complete). If the message cannot be executed for some reason (such as invalid parameters, time-out, and so on) a NAK is returned instead (not-acknowledge).
Page 13
= F0h when only the low byte is used = 240 Christie TruLife+ collects all of the message bytes as defined in the first byte of the message, then creates its own checksum value for comparison with the checksum included in the controller’s message.
Page 14
Normally messages can be sent to the projector before processing of earlier messages is complete— Christie TruLife+ stores messages in a buffer until ready to process. However, if a series of messages is sent, Christie TruLife+ may not be able to process them as fast as they arrive and the buffer becomes full.
Page 15
Serial API commands The Christie TruLife+ commands can be used to modify product settings. ADR–Projector Address Sets or queries the device address. This command also helps to identify where a response or asynchronous message originates from. Generally, this command is used for projectors that are daisy-chained together using the RS232 style communication.
Page 23
To take measurements of each of the color primaries at points (15, 2, 5, 8, and 16), use a spectroradiometer such as the PR-655. Once the measurements are taken, enter the values into the projector using this serial command. For more information on color uniformity, refer to Christie TruLife + User Guide (P/N: 020-103315-XX).
Page 27
Select the second black level blend from the list of available blends: (EBB+SLCT 2) EBL–Edge Blending Select By default, edge blends are not on the projector. Use Christie Twist Pro, Twist Premium, or Mystique to add edge blends to the projector. Commands...
Page 28
Configures which EDID is presented using inputs that support EDIDs (such as DisplayPort, HDMI, DVI, and so on). Use this command to configure what Christie TruLife+ advertises regarding the type of signals it accepts. This command does not need to be set to accept a particular type of signal.
Page 35
Controls or monitors the state of the general purpose inputs and outputs. The pins reserved for 12V and ground cannot be read, set, or configured. For a mapping of the IO pins to the physical connector pins, refer to the Christie TruLife+ User Guide (P/N: 020-103315-XX). Commands...
Page 46
Serial API commands Command Description Values NET+PORT? Returns the TCP port used for the Christie serial 1024 to 49151 (with some protocol over Ethernet. (Read-only) exceptions) 3003 = Reserved on the projector and cannot be used for the Christie serial...
Page 54
Serial API commands SST–Status Returns status information about the projector in read-only mode. For more information about the status groups, items, and their states, see the Christie TruLife+ Status System Guide (P/N: 020-103327-XX). Commands Command Description Values SST? Returns all status items. (Read-only)
Page 64
Corporate offi ces Worldwide offi ces Christie Digital Systems USA, Inc. Africa United Kingdom Columbia Korea (Seoul) ph: 714 236 8610 ph: +27 (0)11 510 0094 ph: +44 (0) 118 977 8000 ph: +57 (318) 447 3179 ph: +82 2 702 1601 Christie Digital Systems Canada Inc.