Toshiba e-STUDIO2330C Service Handbook page 507

Page
7-4 The illustration in Fig. 7-9 has been corrected.
7-5 The illustration in Fig. 7-12 has been corrected.
7-10 Step (3) in the content of the disassembling procedure in "7.1.11 Board Case" has been
divided to steps (3) and (4).
The illustration in Fig. 7-25 has been corrected.
The illustration in Fig. 7-26 has been corrected.
7-12 The content of "Fig. 7-28" in "7.1.12 SRAM board<for LGC board>" has been divided to
"Fig. 7-29" and "Fig. 7-30".
A note and an illustration Fig. 7-31 have been added.
7-13 The illustration in Fig. 7-32 has been corrected.
The content of "Fig. 7-30" in "7.1.13 SRAM board<for SYS board>" has been divided to
"Fig. 7-33" and "Fig. 7-34".
7-14 A note and an illustration Fig. 7-35 have been added.
7-18 The illustration in Fig. 7-37 has been corrected.
7-20 A new procedure has been added in step (1) in "[E] Replace / Format HDD".
7-22 Descriptions in "7.2.4 Procedures and precautions when replacing the SYS board" has
been corrected.
7-23 A new procedure has been added in step (1) in "7.2.5 Procedures and settings when
replacing the SLG board".
7-24 The title "7.2.6 Procedures and settings when replacing SRAM (SYS board)" has been cor-
rected to "7.2.6 Procedures and settings when replacing SRAM board (for SYS board)".
7-28 The title "7.2.7 Procedures and settings when replacing SRAM (LGC board)" has been cor-
rected to "7.2.7 Procedures and settings when replacing SRAM board (for LGC board)".
7-28 A new note has been added in "7.2.7 Procedures and settings when replacing SRAM board
(for LGC board)".
7-28 The introductory part of "7.2.7 Procedures and settings when replacing SRAM board (for
LGC board)" has been corrected.
7-28 The illustration of Fig.7-40 has been corrected.
7-28 The procedure in "[A] Replace SRAM board" has been corrected.
7-30 Descriptions in "7.3 Precautions for Disposal of the HDD and PC Boards" have been
corrected.
8-1 8. FIRMWARE UPDATING
Descriptions about the necessity of a harness jig for the converter firmware update have
been added.
8-2 E. Engine ROM
The illustration of the download jig has been corrected.
8-18 8.2.1 Writing the data to the download jig (PWA-DWNLD-350-JIG2) - [A] Precautions when
writing the System ROM data
A precaution "Loading the data file into the buffer by means of the following settings." has
been added.
8-18 8.2.1 Writing the data to the download jig (PWA-DWNLD-350-JIG2) - [A] Precautions when
writing the System ROM data-[A-1] System ROM
The name of the system ROM file has been corrected.
8-19 8.2.1 Writing the data to the download jig (PWA-DWNLD-350-JIG2) - [B] Precautions when
writing the Engine ROM data
Precautions when writing the Engine ROM data have been added.
8-21 8.2.2 System ROM - [A] Update procedure
Step 9: The procedure for shutting down the equipment has been changed to turning OFF
the power with the main switch.
Step 10: The procedure for starting up the equipment has been changed to turning ON the
power with the main switch.
8-22 8.2.3 Engine ROM - [A] Update procedure
Step 1:The procedure has been corrected to "Write the ROM data to be updated to the
download jig (PWA-DWNLD-350-JIG2)."
© 2008, 2009 TOSHIBA TEC CORPORATION All rights reserved
Ver.02 <2008.06.26>
Contents
7
e-STUDIO2330C/2820C/2830C/3520C/3530C/4520C
REVISION RECORD