Husqvarna TC 250 2010 Workshop Manual page 399

Screw TCEI M5x0.8 L20
Oil drain plug M14x1.5
Drilled screw TEF M8x1.25 (alumi-
nium)
Oil filler plug
Electrical System
Screw TEF M6x1-CH8-L20
Screw TCEI M5-L12
Screw TCEI M5-L20
Flanged nut M12x1
Screw TEF M6x1-CH8-L20
Spark plug
Clutch
Nut M16x1-CH27-SP7
Screw TEF M6x1-CH8-L20
Screw TCEI M6-L16
Screw TCEI M6-L12
Starting system
Screw TCEI M5-L30
Short nut M6x1
Screw TCEI M5-L20
Screw TEF M8-L.15
Gearbox
Nut M16x1
Gear shift control
Selector drum rtng screw M8x1.25
Screw TSEI M6-L14
Screw TEF M6-L14
Screw TEF M5x0.8-CH8-L12
Screw TEF M6x1-CH8-L20
Cooling
Serrated flanged nut M5
Screw TCEI M5 L25
Screw TCEI M5 L30
Cheese-headed Phillips screw M4-
L12
1 Nm = 0.73756 ft/lb
(*): Smear some graphite grease on spark plug thread, do it fully home finger tight then tighten it to 10÷12 Nm torque. Loosen the
spark plug then tighten it again to 10÷12 Nm.
Part. N. 8000 H1489 (10-2009)
TIGHTENING TORQUE FIGURES
Oil pump body
Pipe
Coil to chassis
Stator (use LOCTITE 272)
Pick-up sensor (use LOCTITE 272)
Flywheel
Regulator to chassis
M10x1
Clutch hub
Pressure plate
Clutch cylinder
Clutch cylinder
Starter motor
Gear to starter motor shaft (+LOCTITE 243)
Bevel drive body
Kick start lever (+LOCTITE 272)
Sprocket
Use LOCTITE 270 (or LOCTITE 243)
Selector rtng plate (+LOCTITE 243)
Selector rtng plate (+LOCTITE 243)
Indicator
Gear shift lever
Impeller
(use LOCTITE 270 or LOCTITE 272)
Cover
Cover
Fitting (+LOCTITE 243)
X.3
6 Nm 0.6 Kgm
25 Nm 2.55 Kgm
8 Nm 0.8 Kgm
Finger-tight
8 Nm 0.8 Kgm
6 Nm 0.6 Kgm
6 Nm 0.6 Kgm
75 Nm 7.65 Kgm
8 Nm 0.8 Kgm
(*)
65 Nm 6.6 Kgm
8 Nm 0.8 Kgm
8 Nm 0.8 Kgm
8 Nm 0.8 Kgm
6 Nm 0.6 Kgm
3.9 Nm 0.5 Kgm
6 Nm 0.6 Kgm
25 Nm 2.55 Kgm
90 Nm 9.2 Kgm
25 Nm 2.55 Kgm
8 Nm 0.8 Kgm
8 Nm 0.8 Kgm
6 Nm 0.6 Kgm
8 Nm 0.8 Kgm
6 Nm 0.6 Kgm
6 Nm 0.6 Kgm
1 Nm 0.6 Kgm
3 Nm 0.3 Kgm