Husqvarna TC 250 2010 Workshop Manual page 302

ELECTRICAL SYSTEM
ELECTRONIC IGNITION SYSTEM ........................................................... M.38
Wiring (TC) ................................................................................................ M.39
Cable routing and electrical parts installation instructions (TC)................. M.40
• HT coil position (TC) ............................................................................... M.40
• Fuel injection control unit position (TC) .................................................. M.40
• Securing engine stop button ground cable to chassis (TC) ................... M.40
• Control unit connection (TC) .................................................................. M.41
• Ignition coil connection (TC) ................................................................... M.41
• Gear sensor cable connection (TC) ....................................................... M.41
• Securing the wiring harness (TC) ........................................................... M.42
• Securing the engine stop button cable (TC) ........................................... M.42
• Securing the wiring harness (TC) ........................................................... M.42
Wiring (TE - TXC) ...................................................................................... M.43
CABLE ROUTING AND ELECTRICAL PARTS
INSTALLATION INSTRUCTIONS "TE - TXC" .......................................... M.44
• Coil position TE -TXC ............................................................................ M.44
• Relay and fuses position (TE - TXC) ..................................................... M.44
• Turning indicators flasher (TE) and solenoid starter position
(TE - TXC) .............................................................................................. M.44
• Electronic control unit and voltage regulator position
(TE - TXC). ............................................................................................. M.45
• Securing the starter motor/solenoid starter cable (TE - TXC) ................ M.45
• Securing the engine ground to chassis and engine ground to battery cables
(TE - TXC) ............................................................................................ M.45
• Battery negative cable routing (TE - TXC) ............................................. M.45
• Securing the voltage regulator ground cable (TE - TXC) ....................... M.46
• Securing the engine ground / chassis ground cables. .......................... M.46
Electrical system ground ........................................................................ M.46
• Wiring connection to voltage regulator (TE - TXC) ................................ M.46
• Connection of relays and fuses (TE - TXC) ........................................... M.47
• Electric fan connection (TE - TXC) ........................................................ M.47
• Injector connection (TE - TXC) .............................................................. M.47
• Ignition coil connection (TE - TXC) ........................................................ M.47
• Fuel pump connector position (TE -TXC) .............................................. M.48
• MAQS connector (TE - TXC) ................................................................. M.48
• Engine water temperature connector .................................................... M.48
(TE - TXC) .............................................................................................. M.48
• Lambda sensor position and connector ................................................. M.48
(TE - TXC) .............................................................................................. M.48
• Ignition and gear sensor cable connection ............................................ M.49
• Routing of rear chassis cables, tail light connection,
solenoid starter, flasher. ......................................................................... M.49
• Air box cable routing .............................................................................. M.49
• Clip installation on fuse holders ............................................................. M.49
• Clip installation on fuse holders ............................................................. M.50
• Rear stop connection ............................................................................. M.50
• Routing of steering head tube wiring ..................................................... M.50
• Dashboard bracket connectors (TE) ...................................................... M.50
• Headlamp, front turning indicators , STOP connection (TE)....................... M.50
• Double map connector cap (TE) ............................................................ M.51
• Speed sensor and ignition switch connectors (TE) ................................ M.51
• Horn connector (TE) .............................................................................. M.51
• Securing the wiring harness to rear chassis right side........................... M.52
• Securing the wiring harness to rear chassis left side ............................. M.52
• Securing the wiring harness to the chassis............................................ M.52
• Securing the wiring harness................................................................... M.52
• Securing the wiring harness................................................................... M.53
• Securing the wiring harness................................................................... M.53
• Securing the wiring harness................................................................... M.53
• Securing the wiring harness................................................................... M.53
IMPORTANT .............................................................................................. M.54
M.4 Part. N. 8000 H1489 (10-2009)