Auto Repeater - Icom i9100 Instruction Manual

14
SET MODE
■ Set mode description (Continued)
DUP Offset
18.
Set the offset* for duplex operation. You can set the
repeater offset for each band.
*The difference between transmit and receive frequencies.
➥ When you select this item, hold down [BAND](MAIN/
SUB) for 1 second to select the desired frequency
band. Then, rotate [MAIN DIAL] to set the offset.
• The frequency offset can be set to between 0.0000 MHz
and 9.9999 MHz*.
*99.9999 MHz for the 1200 MHz frequency band.
The default value may differ, depending on the se-
lected frequency band and transceiver version.
NOTE:
• You can use this setting only when the Split func-
tion is OFF for the HF/50 MHz frequency band.
• "-.---.-" is displayed when a blank memory channel
is selected, or the satellite mode is ON.
The optional UX-9100 is required for 1200 MHz frequency
band operation.
One Touch Repeater
19.
Set the one touch repeater shift direction.
• DUP– : The transmit frequency shifts down from the
receive frequency by the offset amount.
• DUP+ : The transmit frequency shifts up from the
receive frequency by the offset amount.

Auto Repeater

20.
(Only U.S.A. and Korea versions)
Set the Auto Repeater function ON or OFF.
To activate the Auto Repeater function, first program the
auto repeater frequency range, then select ON. (p. 67)
U.S.A. version:
• ON–1 : Activates duplex only.
• ON–2 : Activates duplex and tone.
• OFF : Auto repeater function is turned OFF.
Korea version:
• ON : Activates duplex and tone.
• OFF : Auto repeater function is turned OFF.
163
(Default: DUP–)
(Default: ON–1 ; for U.S.A. version
ON ; for Korea version)
Tuner (Auto Start)
21.
Turn the Automatic Antenna Tuner function ON or
OFF. This function is for only the HF bands.
• OFF : The internal antenna tuner remains OFF even
when the SWR is high.
• ON : The internal antenna tuner automatically starts
tuning when the SWR is high, even if the tuner
is turned OFF.
Tuner (PTT Start)
22.
Whenever you push [PTT], the internal or external an-
tenna tuner automatically starts tuning if the operat-
ing frequency has changed by more than 1% from the
last-tuned frequency.
• OFF : Tuning starts only when [TUNER] is pushed.
• ON : (Internal antenna tuner) Tuning starts when
you push [PTT] on a new frequency, if the in-
ternal antenna tuner is ON.
(External antenna tuner) Tuning always starts
when you push [PTT] on a new frequency, re-
gardless of whether the external antenna tuner
is ON or OFF.
Tuner Preset Clear
23.
Select the desired antenna.
The selected antenna's preset memory* is cleared by
holding down [CLR](F-4) for 1 second.
* The variable capacitor settings are memorized as a
preset point for each frequency range (100 kHz steps)
after the tuner matches an antenna.
• CLR ANT1 : The preset memory of [ANT1]'s antenna
is cleared.
• CLR ANT2 : The preset memory of [ANT2]'s antenna
is cleared.
[ANT] Switch
24.
Set the antenna switch function to Auto, Manual or OFF.
When you change the operating frequency on the HF/
50 MHz frequency band, this function will automatically
select the correct antenna, or you must do it manually.
• OFF : [ANT•METER] does not function. The
[ANT1] connector is always selected.
• Manual : You must manually change the antenna by
pushing [ANT•METER].
• Auto : The antenna memorized by the band mem-
ory is automatically selected. You can also
manually change the antenna by pushing
[ANT•METER].
(Default: OFF)
(Default: OFF)
(Default: Auto)