Icom i9100 Instruction Manual page 203

• DV TX call signs setting
Command : 1F 01
Set "UR," "R1" and "R2" call signs of 8 characters (fixed).
q–i o–!6
q–i UR (Destination) call sign setting
o–!6 R1 (Access/Area repeater) call sign setting
!7 – @4 R2 (Link/Gateway repeater) call sign setting
• Character's code of the call sign
Character ASCII code Character ASCII code
0–9 30–39
Space 20
• DV TX message setting
Command : 1F 02
Set the transmit message of up to 20 characters.
See 'Character code setting.' (p. 190)
"FF" stops sending or reading messages.
• DV RX Status setting
Command : 20 0201, 20 0202
Data
Status
Bit
7 0 —
Receiving a voice
call
6 0/1
Last call finisher
5 0/1
Receiving a sig-
4 0/1
nal
Receiving a BK
3 0/1
call
Receiving a EMR
2 0/1
call
Receiving a sig-
1 0/1
nal other than DV
Packet loss status During displaying a packet
0 0/1
• DV RX message setting
Command : 20 0101, 20 0102
q–@0
q–@0 RX message (20 characters; fixed)
@1 – @8 Call sign of the calling station (8 characters; fixed)
@9 – #2 Note of the calling station (4 characters; fixed)
See 'Character code setting.' (p. 190)
"FF" stands for no message receiving after turning
ON the transceiver.
!7 – @4
A–Z 41–5A
⁄ 2F
Description
—
During receiving a digital voice
signal, select "1."
( Regardless of DSQL and
CSQL setting)
When the last call was finished
by you, select "1."
When the audio tone can be
heard, select "1."
During receiving a BK call, se-
lect "1."
During receiving a EMR call,
select "1."
When "DV" and "FM" are blink-
ing, select "1."
loss
@1 – @8 @9 – #2
CONTROL COMMAND
• DV RX call sign setting
Command : 20 0001, 20 0002
q w e–!0
@3 – #0 #1 – #8
q Header flag data (First byte)
Data
Bit
0
7
(fixed)
0
6
(fixed)
0
5
(fixed)
0= Voice, 1= Data
4 0/1
0= Direct, 1= Through repeater
3 0/1
0= No Break-in, 1= Break-in
2 0/1
0= Data, 1= Control
1 0/1
0= Normal, 1= Emergency
0 0/1
w Header flag data (Second byte)
Data
Bit 2 Bit 1 Bit 0
1 1 1
Repeater control
1 1 0
Send auto acknowledge
1 0 1
(Not used)
1 0 0 Request to re-transmit
0 1 1 Send acknowledge
0 1 0 Receive no reply
0 0 1 Repeater disabled
0 0 0 NULL
e–!0 Call sign of the calling station
(8 characters; fixed)
!1 – !4 Note of the calling station
(4 characters; fixed)
!5 – @2 Call sign of the station that was called
(8 characters; fixed)
@3 – #0 Call sign of the access/area repeater (R1)
(8 characters; fixed)
#1 – #8 Call sign of the link/gateway repeater (R2)
(8 characters; fixed)
See 'Character code setting.' (p. 190)
"FF" stands for no call sign receiving after turning
ON the transceiver.
18
!1 – !4 !5 – @2
Description
—
—
—
Function
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
194