Converting Programs From The K2Vx To K2Vx; Programs Using Drum Samples; Effects Programs; Keymaps - Kurzweil K2000 - MUSICIANS GUIDE Musician's Manual

Converting programs from the K2vx to K2000
There may be times when you wish to take a Þle you have created for your K2vx and load it
into a K2000. As we have mentioned in the above section on loading K2000 Þles into the K2vx,
most objects are compatible, but there are a few things you will need to be aware of:

Programs using Drum samples

Since the K2vx has new drum samples, these programs will not translate correctly. The K2vx
drum samples are not available on disk to be loaded into the K2000, so these programs simply
can not be converted so that they will sound identical.
However, if you have some K2vx programs which take advantage of VAST programming and
wish to use them in a K2000, you can load the program into the K2000, then edit the program to
change the keymaps to the corresponding drum keymap. If the keymap is one of the 5 octave or
2 octave kit keymaps, you will Þnd that for the most part, the type of percussion sound will
match up, though there may be a few which don't. Keep in mind though that the sound itself
may be quite different, since the samples are different.

Effects Programs

The preset effects programs in the K2vx are different than in the K2000. However, since these
effects programs consist simply of different values for the various editable parameters, a K2vx
effect can be loaded into the K2000.
Here is the simplest way to include a K2vx effect in your Þle with the program. On the K2vx,
call up the program that you will be porting to the K2000. Press edit and go to the EFFECT
page. Press edit again to enter the Effects Editor. Now press save to save that effect to RAM.
Once it is saved, press exit. You will now see that the RAM effect is assigned to the program.
Press exit and save the program before leaving the editor. If the effect was saved to the same
bank as the program, and you are saving the entire bank, both objects will be saved to the Þle. If
the effect was saved to a different bank or you are selecting only individual programs to be
saved to disk, be sure to answer yes to the "Save Dependent Objects?" question and the effect
will be saved along with the program.
If you have a great number of programs that you want to convert and don't want to edit each of
those programs, there is another method you can use. You can create your own K2000 effects
compatibility Þle, similar to the K2vx effects Þle. This method will require more work initially,
but once it is done, the Þle can easily be used again and again.
To do this, start with the K2vx cleared of all RAM objects. (Go to Master and delete Everything.)
Now go to Effects Mode, call up each effect one by one, going into the Effects Editor and saving
that effect to RAM. Save the effect back to the exact same number it was originally at, choosing
Replace. For instance, save effect #17 back to location #17. (If you have an editor/librarian
software program for your computer, you can get all the effects in one shot and save them to
the same RAM locations.) Now save an Everything Þle to Disk. You now have a Þle similar to
the K2KFX.K25 Þle on the compatibility disks. You can use the exact same set of Þve steps
documented in the section on converting K2000 Þles to the K2vx, but this time you will be
loading the Þles into the K2vx. (Don't forget to delete Everything in the K2vx when you are
done creating the compatibility Þle.)

Keymaps

The following keymaps are either different in the two instruments, or they do not exist in the
K2vx: 20-30 & 173-191. (Keymaps 169-172 have different names in the K2vx but are identical to
the ones in the K2000.) Keymaps 23-30 & 189-191 use drum samples and are therefore can not
be converted to the K2vx (see the section on Drum Samples, above). But keymaps 20-22 & 173-
188 can easily ported to the K2vx. To do this, you will follow the same procedure used to
convert effects programs, documented above. Follow those exact steps, but instead of going to
the EFFECT page, go to the KEYMAP page in the Program Editor.
K2vx Compatibility
Converting programs from the K2vx to K2000
Appendix B-3