Fluke 5500A Operator's Manual page 405

Edit keys, 3-6
EDIT remote command, 6-15
EDIT? remote command, 6-15
Editing and Error Output Settings, 4-49
Editing Output Settings, 4-49
Editing the Output Setting, 4-49
EEPROM Format Menu, 4-6
ENTER key, 3-8
Entering a DC Offset, 4-46
Entering a Phase Angle, 4-44
Entering a Power Factor, 4-45
ERR? remote command, 6-15
ERR_UNIT remote command, 6-16
Error Mode
Operation, 4-17
Error Mode Commands, 6-3
Error Mode, Keys that exit, 4-49
Error Output, Displaying the, 4-50
Error Queue, 5-43
Error Settings, 4-49
ESE
Bit assignments, 5-38
Programming the, 5-39
ESE remote command, 6-16
ESE? remote command, 6-16
ESR
Explained, 5-38
Bit assignments, 5-38
Programming the, 5-39
Register, 5-38
ESR? remote command, 6-16
Event Status
Enable Register (ESE), 5-38
Register (ESR), 5-38
Register Bit assignments, 5-38
EXPLAIN? remote command, 6-17
External Connection Commands, 6-3
Extra Space or Tab Characters, 5-32
—F—
Factory Defaults for SETUP, 4-7
Fan Filter, 3-10
FAULT? remote command, 6-17
Features
Front Panel, 3-4
Rear Panel, 3-10
Features (Chapter 3), 3-3
FORMAT remote command, 6-17
Four-Wire versus Two-Wire Connections, 4-10
Frequency Response Calibration, 8-24, 8-78
Frequency Response Calibration, 8-21
Frequency Response Calibration, 8-74
Frequency specifications, 1-26
Frequency Sweep for Oscilloscope Calibration, 8-24,
8-77
Front Panel Features, 3-3
Front Panel Operation (Chapter 4), 4-3
FUNC? remote command, 6-18
Function Generator, 8-28, 8-82
Fuse, Accessing the, 2-5
Fuse, Non-Operator Replacement, 7-27
Fuse, Replacement, 2-3
Fuse, Replacing the, 7-3
—G—
General Cleaning, 7-6
Guidelines for Programming the Calibrator, 5-43
—H—
HARMONIC remote command, 6-19
HARMONIC? remote command, 6-19
Harmonics
Setting, 4-42
Waveform, 4-42
Harmonics Performance for Amps, Harmonics screen,
4-61
Harmonics Performance for Volts, Harmonics Screen,
4-60
—I—
IDN remote command, 6-20
IEEE-488
Bus Setup Procedure, 5-7
interface, testing the, 5-8
Using for Remote Control, 5-4
IEEE-488 Interface Cable, 9-4
IEEE-488 Interface Messages, 5-26
IEEE-488 Interface Overview, 5-23
IEEE-488 Port, Testing the, 5-8
IEEE-488 Remote Control Connections, 5-5
Incoming Character Processing, 5-33
INCR remote command, 6-20
Input Buffer Operation, 5-47
Inspection, 2-3
Instruction Manuals, 1-6
Instrument Setup, 4-5
Instrument Status
Change Enable Register (ISCE), 5-40
Change Register (ISCR), 5-40
Instrument Status Register, 5-40
Interface Messages
Accepted by 5500A - Table of, 5-27
That the 5500A sends, 5-28
Interface Messages (IEEE-488), 5-26
Introduction and Specifications (Chapter 1), 1-3
ISCE
(continued)
Index
INDEX-3