Fluke 5522A Operators Manuals

Manuals and User Guides for Fluke 5522A Operators. We have 3 Fluke 5522A Operators manuals available for free PDF download: Operator's Manual, Manual

Fluke 5522A Operators Operator's Manual

Fluke 5522A Operators Operator's Manual (426 pages)

Multi-Product Calibrator

Brand: Fluke | Category: Test Equipment | Size: 13.13 MB

Table of Contents

Table of Contents

5
- Introduction and Specifications
  21
- Introduction
  23
- Safety Information
  24
- Operation Overview
  25
  - Local Operation
    25
  - Remote Operation (RS-232)
    26
  - Remote Operation (IEEE-488)
    26
- Overload Protection
  25
- A Glossary
  27
- Instruction Manuals
  27
  - 5522A Getting Started Manual
    27
  - 5522A Operators Manual
    27
- Where to Go from here
  27
- General Specifications
  28
- Detailed Specifications
  29
  - DC Voltage
    29
  - DC Current
    29
  - Resistance
    31
  - AC Voltage (Sine Wave)
    32
  - AC Current (Sine Wave)
    34
  - Capacitance
    36
  - Temperature Calibration (Thermocouple)
    37
  - Temperature Calibration (RTD)
    38
  - DC Power Specification Summary
    38
  - AC Power (45 Hz to 65 Hz) Specification Summary, PF=1
    39
  - Power and Dual Output Limit Specifications
    39
  - Phase
    40
- Additional Specifications
  41
Chapter 2 Preparing for Operations

47
- Preparing for Operations
  47
  - Introduction
    49
- How to Replace the Mains Power Fuse
  49
- Unpack and Inspect
  49
- How to Connect to Line Power
  50
- How to Select Line Frequency
  50
- How to Select Line Voltage
  50
- How to Contact Fluke
  52
- Cooling Considerations
  53
- Placement
  53
- Features
  55
  - Introduction
    57
  - Front-Panel Features
    57
  - Rear-Panel Features
    57
  - Softkey Menu Trees
    57
Chapter 4 Front Panel Operation

77
- Front Panel Operation
  77
- How to Turn on the Calibrator
  79
- Introduction
  79
- How to Use the Setup Menu
  80
- How to Use the Softkeys
  80
- Warming up the Calibrator
  80
- How to Reset the Calibrator
  83
- How to Zero the Calibrator
  83
- How to Connect the Calibrator to a UUT
  84
  - Recommended Cable and Connector Types
    85
  - When to Use EARTH and EXGRD
    85
    
    Earth
    85
    
    External Guard
    86
  - Four-Wire Versus Two-Wire Connections
    86
    
    Compensation off
    86
    
    Four-Wire Connection
    86
    
    Two-Wire Compensation
    86
  - Cable Connections Instructions
    86
- Operate and Standby Modes
  84
- RMS Versus P-P Amplitude
  92
- Auto Range Versus Locked Range
  93
- How to Set Output
  93
- Waveform Types
  117
  - Sine Wave
    117
  - Triangle Waves
    118
  - Square Wave
    118
  - Truncated Sine Wave
    119
- How to Set Harmonics
  119
- How to Adjust the Phase
  120
  - How to Enter a Phase Angle
    122
  - How to Enter a Power Factor
    122
- How to Enter a DC Offset
  123
- Editing and Error Output Settings
  124
  - How to Edit the Output Setting
    124
  - How to Display the UUT Error
    125
  - How to Use Multiply and Divide
    126
- How to Set Output Limits
  126
  - How to Set Voltage and Current Limits
    126
- How to Measure Pressure
  127
- How to Synchronize the Calibrator Using 10 Mhz IN/OUT
  128
- Sample Applications
  131
  - How Calibrate an 80 Series Digital Multimeter
    131
    
    Cables
    132
    
    EARTH Connection
    132
    
    How to Test the Meter
    132
    
    How to Calibrate the Meter
    136
  - How to Test a Model 41 Power Harmonics Analyzer
    136
    
    How to Test Watts, VA, VAR Performance
    136
    
    How to Test Harmonics Volts Performance
    138
    
    How to Test Harmonics Amps Performance
    139
  - How to Calibrate a Fluke 51 Thermometer
    140
    
    How to Test the Thermometer
    140
    
    How to Calibrate the Thermometer
    141
Chapter 5 Remote Operations

143
- Remote Operations
  143
- Introduction
  145
- How to Set up the IEEE-488 Port for Remote Control
  147
  - Remote Commands
    147
  - How to Test the IEEE-488 Port
    149
  - IEEE-488 Port Setup Procedure
    149
- How to Set up the RS-232 Host Port for Remote Control
  151
  - RS-232 Host Port Setup Procedure
    151
  - How to Test the RS-232 Host Port
    153
    
    How to Test RS-232 Host Port Operation with a Terminal
    154
    
    Commands
    156
    
    How to Test RS-232 Host Port Operation with Visual Basic
    156
- How to Set up the RS-232 UUT Port for Remote Control
  157
- How to Change between Remote and Local Operation
  162
  - Local State
    162
  - Local with Lockout State
    162
  - Remote State
    162
  - Remote with Lockout State
    163
- RS-232 Interface Overview
  163
- IEEE-488 Interface Overview
  164
- How to Use Commands
  167
  - Types of Commands
    167
    
    Common Commands
    167
    
    Device-Dependent Commands
    167
    
    Query Commands
    167
    
    Interface Messages (IEEE-488)
    168
  - Compound Commands
    169
    
    Coupled Commands
    170
    
    Overlapped Commands
    170
    
    Commands for RS-232 Only
    171
    
    Commands that Require the Calibration Switch
    171
    
    Sequential Commands
    171
    
    Commands for IEEE-488 Only
    172
  - Command Syntax
    172
    
    Parameter Syntax Rules
    172
    
    Extra Space or Tab Characters
    174
    
    Terminators
    174
    
    Incoming Character Processing
    175
    
    Response Message Syntax
    175
- Checking 5522A Status
  176
  - Serial Poll Status Byte (STB)
    177
    
    Programming the STB and SRE
    179
    
    Service Request (SRQ) Line
    179
    
    Service Request Enable Register (SRE)
    179
  - Event Status Register (ESR)
    180
    
    Bit Assignments for the ESR and ESE
    180
    
    Event Status Enable (ESE) Register
    180
    
    Programming the ESR and ESE
    181
  - Instrument Status Register (ISR)
    182
    
    Bit Assignments for the ISR, ISCR, and ISCE
    182
    
    Instrument Status Change Enable Registers
    182
    
    Instrument Status Change Registers
    182
    
    Programming the ISR, ISCR, and ISCE
    183
  - Output Queue
    184
  - Error Queue
    184
- Remote Program Examples
  184
- Remote Commands
  189
  - Command Summary by Function
    189
  - Introduction
    189
  - Introduction
    191
  - Command Summary by Function
    191
  - Commands
    198
Chapter 7 Maintenance

239
- Maintenance
  239
- How to Replace the Line Fuse
  241
- Introduction
  241
- How to Replace the Current Fuses
  242
- How to Clean the Air Filter
  243
- General Cleaning
  244
- Performance Tests
  245
- Accessories
  259
  - Introduction
    261
  - Rack Mount Kit
    262
  - IEEE-488 Interface Cable
    262
  - Null-Modem Cables
    262
  - 5520A-525A/Leads
    262
Chapter 9 Sc600 Oscilloscope Calibration Option

263
- SC600 Oscilloscope Calibration Option
  263
  - Introduction
    263
    
    How to Use
    263
  - SC600 Oscilloscope Calibration Option Specifications
    265
    
    Introduction
    265
    
    Edge Specifications
    266
    
    General Specifications
    266
    
    Leveled Sine Wave Specifications
    267
    
    Time Marker Specifications
    267
    
    Wave Generator Specifications
    267
    
    Oscilloscope Input Capacitance Measurement Specifications
    268
    
    Oscilloscope Input Resistance Measurement Specifications
    268
    
    Pulse Generator Specifications
    268
    
    Overload Measurement Specifications
    269
  - Oscilloscope Connections
    269
  - How to Start the SC600 Option
    269
    
    How to Adjust the Output Signal
    270
    
    How to Key in a Value
    270
    
    The Output Signal
    270
    
    And
    271
    
    How to Adjust Values with the Rotary Knob
    271
    
    How to Reset the Oscilloscope Option
    272
  - How to Calibrat the Voltage Amplitude on an Oscilloscope
    272
    
    And
    272
    
    How to Use
    272
    
    The Volt Function
    272
    
    Amplitude Calibration Procedure for an Oscillosope
    273
    
    Shortcuts to Set the Voltage Amplitude
    273
    
    The V/DIV Menu
    273
  - How to Calibrate the Pulse and Frequency Response on an Oscilloscope
    274
    
    Pulse Response Calibration Procedure for an Oscilloscope
    275
    
    The Edge Function
    275
    
    Pulse Response Calibration with a Tunnel Diode Pulser
    276
    
    The Leveled Sine Wave Function
    277
    
    Shortcuts for Setting the Frequency and Voltage
    278
    
    The more OPTIONS Menu
    278
    
    How to Sweep through a Frequency Range
    279
    
    Frequency Response Calibration Procedure for an Oscilloscope
    280
  - How to Calibrate the Time Base of an Oscilloscope
    281
    
    The Time Marker Function
    281
    
    Time Base Marker Calibration Procedure for an Oscilloscope
    282
  - How to Test the Trigger SC600 Option
    283
  - How to Test Video Triggers
    284
  - How to Verify Pulse Capture
    285
  - How to Measure Input Resistance and Capacitance
    286
    
    Input Capacitance Measurement
    286
    
    Input Impedance Measurement
    286
  - How to Test Overload Protection
    287
  - Remote Commands and Queries
    288
    
    General Commands
    288
    
    Edge Function Commands
    292
    
    Marker Function Commands
    292
    
    Overload Function Commands
    293
    
    Video Function Commands
    293
    
    Impedance/Capacitance Function Commands
    294
  - Verification Tables
    295
    
    DC Voltage Verification
    295
    
    AC Voltage Amplitude Verification
    296
    
    AC Voltage Frequency Verification
    297
    
    Wave Generator Amplitude Verification: 1 M Output Impedance
    297
    
    Wave Generator Amplitude Verification: 50 Output Impedance
    299
    
    Leveled Sine Wave Verification: Amplitude
    300
    
    Leveled Sine Wave Verification: Frequency
    301
    
    Leveled Sine Wave Verification: Harmonics
    301
    
    Leveled Sine Wave Verification: Flatness
    302
    
    Edge Verification: Amplitude
    310
    
    Edge Verification: Frequency
    310
    
    Edge Verification: Duty Cycle
    311
    
    Edge Verification: Rise Time
    311
    
    Tunnel Diode Pulser Verification
    311
    
    Marker Generator Verification
    312
    
    Pulse Generator Verification: Period
    312
    
    Pulse Generator Verification: Pulse Width
    312
    
    Input Impedance Verification: Capacitance
    313
    
    Input Impedance Verification: Resistance
    313
Chapter 10 Sc1100 Oscilloscope Calibration Option

315
- How to Reset the SC1100 Option
  315
- SC1100 Oscilloscope Calibration Option
  315
- General Specifications
  317
  - Volt Specifications
    318
  - Edge Specifications
    319
  - Leveled Sine Wave Specifications
    319
  - Time Marker Specifications
    320
  - Wave Generator Specifications
    320
  - Pulse Generator Specifications
    321
- Introduction
  317
- SC1100 Option Specifications
  317
- How to Start the SC1100 Option
  322
  - The Output Signal
    323
  - How to Adjust the Output Signal
    323
    
    How to Key in a Value
    323
    
    How to Adjust Values with the Rotary Knob
    324
- Oscilloscope Connections
  322
- How to Calibrate the Voltage Amplitude on an Oscilloscope
  325
  - The VOLT Function
    325
    
    How to Use and
    325
  - The V/DIV Menu
    326
  - Oscilloscope Amplitude Calibration Procedure
    326
- How to Calibrate the Pulse and Frequency Response on an Oscilloscope
  327
- How to Calibrate the Time Base of an Oscilloscope
  334
  - The Time Marker Function
    335
  - Time Base Marker Calibration Procedure for an Oscilloscope
    336
- How to Test the Trigger Functions of an Oscilloscope
  337
- How to Test Video Triggers
  338
- How to Verify Pulse Capture
  339
- How to Measure Input Resistance and Capacitance
  340
  - Input Impedance Measurement
    340
  - Input Capacitance Measurement
    341
- How to Test Overload Protection
  341
- Remote Commands and Queries
  342
  - General Commands
    342
  - Remote Commands and Queries
    343
  - Edge Function Commands
    346
  - Marker Function Commands
    346
  - Video Function Commands
    347
  - Overload Function Commands
    347
  - Impedance/Capacitance Function Commands
    348
- Verification Tables
  349
Chapter 11 Pq Option

371
- PQ Option
  371
- 5522A PQ Option Specifications
  373
- 5522A PQ Specifications
  373
- Introduction
  373
- Composite Harmonics Function (Volts)
  378
  - How to Enter the PQ Modes
    378
  - How to Create Composite Harmonic Waveforms
    378
  - The Wave Selection Menus
    378
  - Recall Wave
    379
  - Save Wave
    379
  - New Wave
    379
  - Edit Wave
    379
  - How to Create New Waves
    379
  - Harmonic Number
    380
  - Harmonic Amplitude
    380
  - Phase
    380
  - How to Edit Waves
    381
  - How to Save Waves
    381
    
    How to Recall Saved Waves
    382
  - Preinstalled Waves
    382
    
    IEC Waves
    382
  - NRC Waves
    383
  - How to Recall Preinstalled IEC Waves
    383
  - How to Recall Preinstalled NRC Waves
    383
- Composite Harmonics Function (Amps)
  383
  - How to Set LCOMP
    384
  - Output aux
    384
- Composite Harmonics Function (Volts and Amps)
  385
  - How to Set LCOMP
    385
  - Output aux
    385
  - REF Menus
    386
- Composite Harmonics Function (Volts and Volts)
  386
  - REF Menus
    387
- Delta ( )Amplitude, Flicker Function (Volts)
  387
  - Delta ( ) Amplitude Mode (Volts)
    387
  - How to Select the Flicker Function
    387
  - How to Set the Repeat Frequency
    387
  - How to Set the Modulation Pattern
    387
  - How to Set the Flicker Amplitude
    388
  - PST Values
    388
  - How to Set Phase and Reference in the AMPL Function
    388
- Delta ( ) Amplitude, Flicker Function (Current)
  388
  - Delta ( ) Amplitude Mode (Amps)
    388
  - More Information
    389
- Delta ( ) Amplitude, Single (Sags & Swells) Function (Volts)
  389
  - Delta ( ) Amplitude Mode (Volts)
    389
  - How to Set the Ramp-Up Period
    389
  - How to Set the Sag & Swell Width
    389
  - How to Set the Sag/Swell Amplitude
    389
  - How to Set Triggers
    390
  - Example
    390
- Delta ( ) Amplitude, Single (Sags & Swells) Function (Current)
  390
  - Delta ( ) Amplitude Mode (AMPS)
    390
  - How to Set Triggers
    391
  - How to Set the Ramp-Up Period
    391
  - How to Set the Sag/Swell Width
    391
  - How to Set the Sag/Swell Amplitude
    391
  - Delta ( )Amplitude Mode (Volts and Amps)
    391
  - Example
    391
  - Remote Commands
    392
  - Commands
    392
  - Example Strings
    397
- Performance Tests
  398
- Verification Table
  398
  - Offset Error
    409
  - Scale Error
    410
  - Specifications
    411
- B ASCII and IEEE-488 Bus Codes
  413
- D Error Messages
  421

Advertisement

Fluke 5522A Operators Operator's Manual

Fluke 5522A Operators Operator's Manual (426 pages)

Multi-Product Calibrator

Brand: Fluke | Category: Test Equipment | Size: 13.11 MB

Table of Contents

Table of Contents
5
Introduction
23
Safety Information
24
Overload Protection
25
Operation Overview
25
Local Operation
25
Remote Operation (RS-232)
26
Remote Operation (IEEE-488)
26
Where to Go from here
27
Instruction Manuals
27
5522A Getting Started Manual
27
5522A Operators Manual
27
General Specifications
28
Detailed Specifications
29
DC Voltage
29
DC Current
29
Resistance
31
AC Voltage (Sine Wave)
32
AC Current (Sine Wave)
34
Capacitance
36
Temperature Calibration (Thermocouple)
37
Temperature Calibration (RTD)
38
DC Power Specification Summary
38
Power and Dual Output Limit Specifications
39
Phase
40
Additional Specifications
41
Frequency
41
Harmonics (2 Nd to
41
AC Voltage (Sine Wave) Extended Bandwidth
42
AC Voltage (Non-Sine Wave)
42
AC Voltage, DC Offset
44
AC Voltage, Square Wave Characteristics
44
AC Voltage, Triangle Wave Characteristics
44
AC Current (Non-Sine Wave)
44
AC Current, Square Wave Characteristics
45
AC Current, Triangle Wave Characteristics
45
Preparing for Operations
47
Introduction
49
Unpack and Inspect
49
How to Replace the Mains Power Fuse
49
How to Select Line Voltage
50
How to Connect to Line Power
50
How to Select Line Frequency
50
How to Contact Fluke
52
Placement
53
Cooling Considerations
53
Features
55
Introduction
57
Front-Panel Features
57
Rear-Panel Features
57
Softkey Menu Trees
57
Front Panel Operation
77
Introduction
79
How to Turn on the Calibrator
79
Warming up the Calibrator
80
How to Use the Softkeys
80
How to Use the Setup Menu
80
How to Use the Instrument Setup Menu
81
How to Use the Setup Menu
81
Utility Functions Menu
82
How to Use the NV Memory Menu
82
How to Reset the Calibrator
83
How to Zero the Calibrator
83
Operate and Standby Modes
84
How to Connect the Calibrator to a UUT
84
Recommended Cable and Connector Types
85
When to Use EARTH and EXGRD
85
Earth
85
How to Connect the Calibrator to a UUT
85
External Guard
86
Four-Wire Versus Two-Wire Connections
86
Four-Wire Connection
86
Two-Wire Compensation
86
Compensation off
86
Cable Connections Instructions
86
RMS Versus P-P Amplitude
92
Auto Range Versus Locked Range
93
How to Set Output
93
How to Set DC Voltage Output
94
How to Set AC Voltage Output
95
How to Set Output
95
How to Set DC Voltage Output
95
How to Set DC Current Output
95
How to Set AC Current Output
95
How to Set DC Power Output
95
How to Set AC Power Output
95
How to Set Capacitance Output
95
How to Set DC Current Output
98
How to Set AC Current Output
99
How to Set DC Power Output
100
How to Set AC Power Output
102
How to Set a Dual DC Voltage Output
105
How to Set a Dual AC Voltage Output
106
How to Set Resistance Output
109
How to Set Capacitance Output
110
How to Set Temperature Simulation (Thermocouple)
111
How to Set Temperature Simulation (RTD)
114
How to Measure Thermocouple Temperatures
115
Waveform Types
117
Sine Wave
117
Triangle Waves
118
Square Wave
118
Truncated Sine Wave
119
How to Set Harmonics
119
How to Adjust the Phase
120
How to Adjust the Phase
121
How to Enter a Phase Angle
122
How to Enter a Power Factor
122
How to Enter a DC Offset
123
Editing and Error Output Settings
124
How to Edit the Output Setting
124
How to Display the UUT Error
125
How to Use Multiply and Divide
126
How to Set Output Limits
126
How to Set Voltage and Current Limits
126
How to Measure Pressure
127
How to Synchronize the Calibrator Using 10 Mhz IN/OUT
128
How to Use an External 10 Mhz Clock
128
How to Source AC Current and Parallel-Connected 5522As
129
How to Synchronize the Calibrator Using 10 Mhz IN/OUT
129
Three-Phase Power Calibration
130
Sample Applications
131
How Calibrate an 80 Series Digital Multimeter
131
Three-Phase Power Calibration
131
Cables
132
EARTH Connection
132
How to Test the Meter
132
How to Calibrate the Meter
136
How to Test a Model 41 Power Harmonics Analyzer
136
How to Test Watts, VA, VAR Performance
136
How to Test Harmonics Volts Performance
138
How to Test Harmonics Amps Performance
139
How to Calibrate a Fluke 51 Thermometer
140
How to Test the Thermometer
140
How to Calibrate the Thermometer
141
Remote Operations
143
Introduction
145
How to Set up the IEEE-488 Port for Remote Control
147
IEEE-488 Port Setup Procedure
149
How to Test the IEEE-488 Port
149
How to Set up the RS-232 Host Port for Remote Control
151
RS-232 Host Port Setup Procedure
151
How to Test the RS-232 Host Port
153
How to Test RS-232 Host Port Operation with a Terminal
154
How to Test RS-232 Host Port Operation with Visual Basic
156
How to Set up the RS-232 UUT Port for Remote Control
157
RS-232 UUT Port Setup Procedure
157
How to Test the RS-232 UUT Port Via RS-232 Host Port
158
How to Test RS-232 UUT Port Operation Via a Terminal
159
How to Test RS-232 UUT Port Operation with Visual Basic
160
How to Test the RS-232 UUT Port Via IEEE-488 Port
160
How to Change between Remote and Local Operation
162
Local State
162
Local with Lockout State
162
Remote State
162
Remote with Lockout State
163
RS-232 Interface Overview
163
Local with Lockout State
163
IEEE-488 Interface Overview
164
IEEE-488 Interface Overview
165
How to Use Commands
167
Types of Commands
167
Device-Dependent Commands
167
Common Commands
167
Query Commands
167
Interface Messages (IEEE-488)
168
Compound Commands
169
Coupled Commands
170
Overlapped Commands
170
Sequential Commands
171
Commands that Require the Calibration Switch
171
Commands for RS-232 Only
171
Commands for IEEE-488 Only
172
Command Syntax
172
Parameter Syntax Rules
172
Extra Space or Tab Characters
174
Terminators
174
Incoming Character Processing
175
Response Message Syntax
175
Checking 5522A Status
176
Serial Poll Status Byte (STB)
176
Service Request Enable Register (SRE)
176
Event Status Register (ESR)
176
Event Status Enable (ESE) Register
176
Serial Poll Status Byte (STB)
177
Instrument Status Change Registers
178
Instrument Status Change Enable Registers
178
Service Request (SRQ) Line
179
Service Request Enable Register (SRE)
179
Programming the STB and SRE
179
Event Status Register (ESR)
180
Event Status Enable (ESE) Register
180
Bit Assignments for the ESR and ESE
180
Programming the ESR and ESE
181
Instrument Status Register (ISR)
182
Instrument Status Change Registers
182
Instrument Status Change Enable Registers
182
Bit Assignments for the ISR, ISCR, and ISCE
182
Programming the ISR, ISCR, and ISCE
183
Output Queue
184
Error Queue
184
Remote Program Examples
184
Guidelines for Programming the Calibrator
184
Writing an SRQ and Error Handler
185
Verifying a Meter in the IEEE-488 Bus
186
Verifying a Meter on the RS-232 UUT Serial Port
186
Using *OPC?, *OPC, and *WAI
186
Taking a Thermocouple Measurement
187
Taking a Pressure Measurement
187
Using the RS-232 UUT Port to Control an Instrument
188
Input Buffer Operation
188
Remote Commands
189
Introduction
191
Command Summary by Function
191
Commands
198
Maintenance
239
Introduction
241
How to Replace the Line Fuse
241
How to Replace the Current Fuses
242
How to Clean the Air Filter
243
General Cleaning
244
Performance Tests
245
Accessories
259
Introduction
261
Rack Mount Kit
262
IEEE-488 Interface Cable
262
Null-Modem Cables
262
5520A-525A/Leads
262
SC600 Oscilloscope Calibration Option
263
Introduction
265
SC600 Oscilloscope Calibration Option Specifications
265
General Specifications
266
Voltage Function Specifications
266
Edge Specifications
266
Leveled Sine Wave Specifications
267
Time Marker Specifications
267
Wave Generator Specifications
267
Pulse Generator Specifications
268
Trigger Signal Specifications (Pulse Function)
268
Trigger Signal Specifications (Time Marker Function)
268
Trigger Signal Specifications (Edge Function)
268
Trigger Signal Specifications (Square Wave Voltage Function)
268
Trigger Signal Specifications
268
Oscilloscope Input Resistance Measurement Specifications
268
Oscilloscope Input Capacitance Measurement Specifications
268
Overload Measurement Specifications
269
Oscilloscope Connections
269
How to Start the SC600 Option
269
The Output Signal
270
How to Adjust the Output Signal
270
How to Key in a Value
270
How to Adjust Values with the Rotary Knob
271
How to Use and
272
How to Reset the Oscilloscope Option
272
How to Calibrat the Voltage Amplitude on an Oscilloscope
272
The Volt Function
272
The V/DIV Menu
273
Shortcuts to Set the Voltage Amplitude
273
Amplitude Calibration Procedure for an Oscillosope
273
How to Calibrate the Pulse and Frequency Response on an Oscilloscope
274
The Edge Function
275
Pulse Response Calibration Procedure for an Oscilloscope
275
Pulse Response Calibration with a Tunnel Diode Pulser
276
The Leveled Sine Wave Function
277
Shortcuts for Setting the Frequency and Voltage
278
The more OPTIONS Menu
278
How to Sweep through a Frequency Range
279
Frequency Response Calibration Procedure for an Oscilloscope
280
How to Calibrate the Time Base of an Oscilloscope
281
The Time Marker Function
281
Time Base Marker Calibration Procedure for an Oscilloscope
282
How to Test the Trigger SC600 Option
283
How to Test Video Triggers
284
How to Verify Pulse Capture
285
How to Measure Input Resistance and Capacitance
286
Input Impedance Measurement
286
Input Capacitance Measurement
286
How to Test Overload Protection
287
Remote Commands and Queries
288
General Commands
288
Edge Function Commands
292
Marker Function Commands
292
Video Function Commands
293
Overload Function Commands
293
Impedance/Capacitance Function Commands
294
Verification Tables
295
DC Voltage Verification
295
AC Voltage Amplitude Verification
296
AC Voltage Frequency Verification
297
Wave Generator Amplitude Verification: 50 Ω Output Impedance
299
Leveled Sine Wave Verification: Amplitude
300
Leveled Sine Wave Verification: Frequency
301
Leveled Sine Wave Verification: Harmonics
301
Leveled Sine Wave Verification: Flatness
302
Edge Verification: Amplitude
310
Edge Verification: Frequency
310
Edge Verification: Duty Cycle
311
Edge Verification: Rise Time
311
Tunnel Diode Pulser Verification
311
Marker Generator Verification
312
Pulse Generator Verification: Period
312
Pulse Generator Verification: Pulse Width
312
Input Impedance Verification: Resistance
313
Input Impedance Verification: Capacitance
313
SC1100 Oscilloscope Calibration Option
315
SC1100 Option Specifications
317
General Specifications
317
Introduction
317
Volt Specifications
318
Edge Specifications
319
Leveled Sine Wave Specifications
319
Time Marker Specifications
320
Wave Generator Specifications
320
Pulse Generator Specifications
321
Trigger Signal Specifications (Pulse Function)
321
Trigger Signal Specifications (Time Marker Function)
321
Oscilloscope Connections
322
How to Start the SC1100 Option
322
The Output Signal
323
How to Adjust the Output Signal
323
How to Key in a Value
323
How to Adjust Values with the Rotary Knob
324
How to Reset the SC1100 Option
325
How to Use X and D
325
How to Calibrate the Voltage Amplitude on an Oscilloscope
325
The VOLT Function
325
The V/DIV Menu
326
Oscilloscope Amplitude Calibration Procedure
326
How to Calibrate the Pulse and Frequency Response on an Oscilloscope
327
The Edge Function
328
Oscilloscope Pulse Response Calibration Procedure
328
The Leveled Sine Wave Function
330
Shortcuts for Setting the Frequency and Voltage
331
The more OPTIONS Menu
331
How to Sweep through a Frequency Range
332
Oscilloscope Frequency Response Calibration Procedure
333
How to Calibrate the Time Base of an Oscilloscope
334
The Time Marker Function
335
Time Base Marker Calibration Procedure for an Oscilloscope
336
How to Test the Trigger Functions of an Oscilloscope
337
How to Test Video Triggers
338
How to Verify Pulse Capture
339
How to Measure Input Resistance and Capacitance
340
Input Impedance Measurement
340
Input Capacitance Measurement
341
How to Test Overload Protection
341
Remote Commands and Queries
343
Edge Function Commands
346
Marker Function Commands
346
Video Function Commands
347
Overload Function Commands
347
Impedance/Capacitance Function Commands
348
Verification Tables
349
DC Voltage Verification
349
AC Voltage Verification
351
AC Voltage Frequency Verification
352
Wave Generator Amplitude Verification: 1 MΩ Output Impedance
353
Edge Verification: Amplitude
355
Edge Verification: Frequency
356
Edge Verification: Duty Cycle
356
Edge Verification: Rise Time
356
Leveled Sinewave Verification: Amplitude
357
Tunnel Diode Pulser Verification
357
Leveled Sinewave Verification: Frequency
358
Leveled Sinewave Verification: Harmonics
358
Leveled Sinewave Verification: Flatness
360
Marker Generator Verification
367
Pulse Generator Verification: Period
368
Pulse Generator Verification: Pulse Width
368
Input Impedance Verification: Resistance
369
Input Impedance Verification: Capacitance
369
PQ Option
371
5522A PQ Specifications
373
5522A PQ Option Specifications
373
Composite Harmonic Function Specifications
373
Introduction
373
AC Voltage Specifications
374
AC Voltage Auxiliary Specifications (Dual Output Mode Only)
375
AC Current Specifications, LCOMP off
375
AC Current Specifications, LCOMP off (Continued)
376
AC Current Specifications, LCOMP on
376
Flicker Simulation Mode
377
Sags & Swells Simulation Mode
377
Phase Specifications, Sinewave Outputs
377
Composite Harmonics Function (Volts)
378
How to Enter the PQ Modes
378
How to Create Composite Harmonic Waveforms
378
The Wave Selection Menus
378
Recall Wave
379
Save Wave
379
New Wave
379
Edit Wave
379
How to Create New Waves
379
Harmonic Number
380
Harmonic Amplitude
380
Phase
380
How to Edit Waves
381
How to Save Waves
381
How to Recall Saved Waves
382
Preinstalled Waves
382
IEC Waves
382
NRC Waves
383
How to Recall Preinstalled IEC Waves
383
How to Recall Preinstalled NRC Waves
383
Composite Harmonics Function (Amps)
383
How to Set LCOMP
384
Output aux
384
Composite Harmonics Function (Volts and Amps)
385
How to Set LCOMP
385
Output aux
385
Φ & REF Menus
386
Composite Harmonics Function (Volts and Volts)
386
Φ & REF Menus
387
Delta (Δ)Amplitude, Flicker Function (Volts)
387
Delta (Δ) Amplitude Mode (Volts)
387
How to Select the Flicker Function
387
How to Set the Repeat Frequency
387
How to Set the Modulation Pattern
387
How to Set the Flicker Amplitude
388
PST Values
388
How to Set Phase and Reference in the ΔAMPL Function
388

Fluke 5522A Operators Manual

Fluke 5522A Operators Manual (56 pages)

Brand: Fluke | Category: Test Equipment | Size: 5.03 MB

Table of Contents

Table of Contents
2
Electrical Calibration
4
DC/LF Electrical Calibrators
7
Specialty Calibrators
8
Oscilloscope Calibrators
9
Precision Multimeters
9
Electrical Standards
10
RF References
12
Temperature Calibration
13
Standard Platinum Resistance Thermometers
20
Fixed-Point Cells
20
Cell Maintenance Apparatus
21
Thermometer Readouts
22
Reference Prts
23
Thermocouples
23
Thermistors
23
Compact Calibration Baths
24
Standard Calibration Baths
24
Special Application Baths
25
Bath Controllers
25
Metrology Wells
25
Field Metrology Wells
25
Dual-Block Dry-Well
26
Field Dry-Well Calibrators
26
Micro-Baths
26
Portable Calbration Baths
26
Handheld Calibrators
26
Infrared Calibrators
27
Zero-Point Dry-Well
27
Surface Probe Calibrator
27
Thermocouple Furnaces
27
Humidity Calibration
28
Humidity Calibrators
29
Pressure Calibration
30
Gas Pressure Controllers/Calibrators
34
Series Piston Gauges
34
High Pressure Controllers/Calibrators
35
Reference Pressure Indicators
35
2400 Series Piston Gauges
36
Specialty Piston Gauges
37
Manual Pressure Generation and Control
37
Industrial Deadweight Testers
38
Pressure Comparators
38
Pressure Calibrators
39
Air Data Calibration
40
Pressure Calibration Systems
40
Gas Flow Calibration
41
Gas Flow Standards
42
Calibration Software
43
Electrical and RF Calibration Software
45
Calibration Asset Management Software
45
Software Support Programs
45
Temperature Calibration Software
46
Pressure/Flow Calibration Software
47
Data Acquisition
48
2638A Hydra Series III Data Acquisition System
49

Advertisement

Advertisement

Related Products

Fluke Categories

Measuring Instruments Test Equipment Multimeter Thermometer Laboratory Equipment

More Fluke Manuals