Programming Stay Mode 2 Zones; Disarming The System; User Codes; Adding User Codes - Bosch ICP-CC404 User Manual

ICP-CC404 | User's Guide | 5.0
Any zones programmed to be automatically isolated
in STAY Mode 2 flash until Exit Time expires. At
the end of Exit Time, the indicators turn off for all
zones selected to be automatically isolated and the
codepad sounds one short beep.
4.4

Programming STAY Mode 2 Zones

If you have a Master Code, you can only program
zones to be automatically isolated in STAY Mode 2.
How to Program STAY Mode 2 Zones
1. Enter your four-character Master Code and press
[4 #] key (for example, [2 5 8 0 4 #]).
Three beeps sound and the STAY indicator
flashes.
2. Enter the zone number to automatically isolate
and press [*] (for example, [1 *] for Zone 1 or
[2 *] for Zone 2).
The selected zone flashes.
If you make a mistake, enter the same zone
number and press [#] to clear the incorrect zone.
To select additional zones to automatically
isolate in STAY Mode 2, repeat Step 2 as many
times as necessary.
3. After you select the zones to automatically isolate
in STAY Mode 2, press [#] to exit from this
mode.
Two beeps sound and the STAY and AWAY
indicators turn dark.

5.0 Disarming the System

When you enter the premises after the system is
armed in AWAY Mode, or if you armed the system
in STAY Mode 1 or STAY Mode 2, you must disarm
the system before entry time expires to disable
detection devices that activate an alarm. Only your
installer can program the entry time.
If there was an alarm before you disarm the system,
a flashing zone indicator shows a previous alarm on
that zone.
To disarm the system:
Enter your user code and press [#] key (for example,
[2 5 8 0 #]).
Two beeps sound.

6.0 User Codes

6.1

Adding User Codes

Only the Master Code holder can add or change
other system user codes, including the Master Code.
The Master Code holder can program up to eight
user codes for the system.
To add a user code:
8
Disarming the System
1. Enter your four-character Master Code and press
[1 #] (for example, [2 5 8 0 1 #]).
Three beeps sound and the STAY and AWAY
indicators flash.
2. Enter the user code number (1 to 8) and press
[#] (for example, [2 #] for User 2, or [8 #] for
User 8).
Two beeps sound and the selected user number
appears on the codepad indicators.
3. Enter the digits required for the new code and
press [#] (for example, for user code 5768, enter
[5 7 6 8 #]).
Two beeps sound and the STAY and AWAY
indicators turn off.
To add or change other user codes, repeat this
procedure as many times as necessary.
6.2

Adding Radio Remote User Codes

Only the Master Code holder can add or change
other system user codes, including the Master Code.
The Master Code holder can program up to eight
radio user codes (User Codes 9 to 16) for the system.
To add a radio remote user code:
1. Enter your four-character Master Code and press
[1 #] (for example, [2 5 8 0 1 #]).
Three beeps sound and the STAY and AWAY
indicators flash.
2. Enter the radio remote user code number
(9 to 16) and press [#] (for example, [9 #] for
User 9, or [1 6 #] for User 16).
Two beeps sound and the selected user number
appears on the codepad indicators.
3. Press any button on the keyfob so the system
learns the ID number. Two beeps sound and the
STAY and AWAY indicators turn off.
To add or change other radio remote user codes,
repeat this procedure as many times as required.
6.3 Deleting User Codes/Radio User
Codes
Only the Master Code holder can delete other
system user codes.
To delete a user code:
1. Enter your four-character Master Code and press
[1 #] (for example, [2 5 8 0 1 #]).
Three beeps sound and the STAY and AWAY
indicators flash.
2. Enter the user code number (User Code 1 to 8,
or Radio User Code 9 to 16) and press [#] (for
example, [2 #] for User 2, [1 6 #] for User 16).
Two beeps sound and the selected user number
appears on the codepad indicators.
3. Press the [*] key to delete the selected user code.
Two beeps sound and the STAY and AWAY
indicators turn off. To delete other user codes,
repeat this procedure as many times as required.
Bosch Security Systems, Inc. | 10/08 | F01U089400-01