Furuno FMD-3200-BB Instruction Manual page 13

• [JH 20T17FUD (UXGA)]
• [JH 23T12FUD (UXGA)]*
• [JH 23T14FUD (UXGA)]
• [JH 26T11MMD (WUXGA)]*
• [HD 19T21MMD (SXGA)]*
• [HD 24T21MMD (FHD)]*
• [HD 24T21MMD (WUXGA)]*
• [HD 24T22FUD (FHD)]*
1
* : When the serial number of the MU-270W is "1000-4610-" or "10", se-
lect [MU-270W (WUXGA)]. If not, select [MU-270W-B (WUXGA)].
2
* : Do not use for the monitor connected to the DVI1 port. These monitors are avail-
able for the port other than DVI1 port.
3
* : Not used.
4
* : ECDIS only.
Note 1: The DVI2 port outputs the display data same as the data of DVI1 port.
Note 2: If the MU-201, MU-231CE or the monitor of Hatteland Display is connect-
ed, the optional cable DSUB9P-X2-A-L5M/L10M for brilliance control is required
to connect.
4. Select the monitor type and resolution connected to the DVI3 port from the [Type
Number] pull-down list of DVI3.
When the processor unit is not connected to the VDR or you do not use the dual
display, select [Not Connected (NONE)] and go to the step 8.
5. Select the display data to output from the DVI3 port from the [Output Mode] pull-
down list.
Setting option
[Clone] DVI1 to DVI3 ports output the same resolution and display data. For the
ECDIS, the DVI1 port can switch ECDIS and Conning display data.
Note 1: When [Clone] is selected, the [Type Number] for DVI1 and
DVI3 port should be same setting option.
Note 2: When the Chart Radar is connected to a VDR, it is required to
set to [Clone].
[Independent] The DVI3 port outputs the conning display data.
Note: Do not set to [Independent] in case of the Chart Radar, when the
CPU board of the EC-3000 is "ADP-555-xx".
6. When one of the following monitors is selected at step 3, click the [Run] button for
[Monitor Color Calibration] to perform the color calibration. For all other monitors,
go to step 8.
• [HD 19T21MMD (SXGA)]
• [HD 24T21MMD (FHD)]
• [HD 24T21MMD (WUXGA)]
• [HD 24T22FUD (FHD)]
• [HD 24T22FUD (WUXGA)]
• [HD 26T21MMD (WUXGA)]
• [HD 26T22MMD (WUXGA)]
"Processing" appears at the next to the [Run] button during the color calibration.
After completing the calibration, check result appears ([Succeeded] or [Failed]).
1. INITIAL SETTING AND ADJUSTMENT
• [HD 55T22FUD (WUXGA)]
2
• [NI WA460-01.MON.01(FHD)]*
• [NI WA460-01.MON.01(WUXGA)]
2
• [NI WA270-01.MON.01-XXFU(FHD)]*
2
• [NI WA270-01.MON.01-XXFU(WUXGA)]
2, 4
* • [AHD 119F (SXGA)]*
2
• [AHD 119G (SXGA)]*
4
Remarks
• [HD 26T22FUD (WUXGA)]
• [HD 27T22FUD (FHD)]
• [HD 27T22FUD (WUXGA)]
• [HD 32T22FUD (FHD)]
• [HD 32T22FUD (WUXGA)]
• [HD 55T22FUD (FHD)]
• [HD 55T22FUD (WUXGA)]
4
4
3
3
1-7