Mitsubishi Electric MELDAS C6 Interface Manual page 68

4. TABLE OF INPUT/OUTPUT SIGNALS WITH CONTROLLER
As for the following signals, initial values at power ON are different depending on the model.
C6/C64 : "1" is set when the power is turned ON. If the following signals are not used,
processing by PLC is not necessary.
C64T : "0" is set when the power is turned ON. If necessary, do process using PLC.
(1) Axis state signal
1st 2nd 3rd 4th
axis axis axis axis
Y441 Y471 Y4A1 Y4D1 Y501 Y531 Y561 Y591 Y5C1 Y5F1 Y621 Y651 Y681 Y6B1
Y443 Y473 Y4A3 Y4D3 Y503 Y533 Y563 Y593 Y5C3 Y5F3 Y623 Y653 Y683 Y6B3
Y444 Y474 Y4A4 Y4D4 Y504 Y534 Y564 Y594 Y5C4 Y5F4 Y624 Y654 Y684 Y6B4
Y445 Y475 Y4A5 Y4D5 Y505 Y535 Y565 Y595 Y5C5 Y5F5 Y625 Y655 Y685 Y6B5
Y446 Y476 Y4A6 Y4D6 Y506 Y536 Y566 Y596 Y5C6 Y5F6 Y626 Y656 Y686 Y6B6
Y447 Y477 Y4A7 Y4D7 Y507 Y537 Y567 Y597 Y5C7 Y5F7 Y627 Y657 Y687 Y6B7
Y448 Y478 Y4A8 Y4D8 Y508 Y538 Y568 Y598 Y5C8 Y5F8 Y628 Y658 Y688 Y6B8
(2) Part system state signal
1st 2nd 3rd
system system system
Y711 Y7F1 Y8D1
Y713 Y7F3 Y8D3
Y714 Y7F4 Y8D4
Y71B Y7FB Y8DB
Y728 Y808 Y8E8
Y760 Y840 Y920
Y762 Y842 Y922
Y764 Y844 Y924
Y774 Y854 Y934
Y7AE Y88E Y96E
Interface Table Output Y
5th 6th 7th 8th
axis axis axis axis
4th 5th 6th
system system system
Y9B1 YA91 YB71
Y9B3 YA93 YB73
Y9B4 YA94 YB74
Y9BB YA9B YB7B
Y9C8 YAA8 YB88
YA00 YAE0 YBC0
YA02 YAE2 YBC2
YA04 YAE4 YBC4
YA14 YAF4 YBD4
YA4E YB2E YC0E
9th 10th 11th 12th
axis axis axis axis
7th
system Abbrev.
YC51 *SP
YC53 *BSL
YC54 *CSL
YC5B *CDZ
YC68 ABS
YCA0 *FV1
YCA2 *FV4
YCA4 *FV16
YCB4 *JV16
YCEE *CXS7
4-25
13th 14th
axis B Signal details
axis
* Servo OFF
* External deceleration +
* External deceleration -
* Auto interlock +
* Auto interlock -
* Manual interlock +
* Manual interlock -
Signal details
Auto operation "pause" command
Block start interlock
Cutting block start interlock
Chamfering
Manual absolute
Cutting feedrate override 1
Cutting feedrate override 4
Cutting feedrate override 16
Manual feedrate 16
Stop