Pontiac Fiero 1988 Service Manual page 177

3B4-8 STEERING WHEELS AND COLUMNS
M l S T A M D M B S T E i i B N © C O L U M N S
1. R E M O V E AND I N S T A L L LOCK P L A T E
AND/OH CANCELLING CAM
REMOVE
1. Remove parts as s h o w n .
I N S T A L L
1. install parts as s h o w n .
S H A F T L O C K C O V E R -
R E T A I N I N G R I N G -
S H A F T L O C K -
C A N C E L L I N G CAM A S S E M B L Y -
S P R I N G - ,
H O U S I N G - !
Pry out at these
locations to
remove cover -
R E M O V E S H A F T L O C K
C O V E R
Tighten nut until tool slightly
depresses shaft lock.
REMOVE A N D INSTALL
R E T A I N I N G RING
2. R E M O V E AND I N S T A L L TURN S I G N A L SWITCH
I N S T A L L
R E M O V E
1 . R e m o v e parts
as s h o w n .
S C R E W 7
1. Install parts
as s h o w n .
S W I T C H A C T U A T O R /
A R M A S S E M B L Y (On Dimmer /
switch c o l u m n o n l y ) ^ w
S C R E W
T U R N S I G N A L
S W I T C H
A S S E M B L Y
W I R E P R O T E C T O R
R E M O V E AND I N S T A L L IGNITION LOCK
AND K E Y WARNING B U Z Z E R
R E M O V E
1. T u r n lock to " R U N "
p o s i t i o n and remove key
w a r n i n g buzzer switch.
2. Remove parts as s h o w n .
T o a s s e m b l e , rotate to stop
while holding c y l i n d e r .
L O C K
C Y L I N D E R
L O C K
R E T A I N I N G
S C R E W ,
I N S T A L L
. Install lock c y l i n d e r .
>. T u r n lock to " R U N "
position and install
key warning buzzer switch
(""KEY
W A R N I N G
B U Z Z E R
S W I T C H
C L I P
K E Y W A R N I N G
B U Z Z E R
S W I T C H
H O U S I N G
R E M O V E K E Y W A R N I N G
| B U Z Z E R S W I T C H
R E M O V E AND I N S T A L L H O U S I N G AND
WIPER S W I T C H
R E M O V E
R e m o v e ignition and
diminer s w i t c h .
Refer i o step 5
R e m o v e parts as s h o w n .
For K E Y R E L E A S E
Tnn^mr PIVOT SWITCH
H O U S I N G - , ASSEMBLY (On
w a s h / w i p e
c o l u m n o n l y H
T H R U S T
W A S H E R
I N S T A L L
1. F o r K E Y R E L E A S E
refer b e l o w .
2. A s s e m b l e rack so that first
rack tooth engages between
first and second tooth of
sector.
3. Install parts as s h o w n .
Install ignition and
dimmer s w i t c h .
Refer to step 5.
S W I T C H P I V O T P I N
H E X
H E A D
S C R E W
S E C T O R
B E A R I N G R E T A I N E R
B U S H I N G
B E A R I N G '
R E T A I N E R
V
G A T E
%
N O T E : H o u s i n g w i t h o u t bearing retainer and bushing has s p u n -
in bearing. If repair is necessary, c o m p l e t e h o u s i n g assembly
replacement is necessary.
Punch
R E M O V E A N D
I N S T A L L S E C T O R
W A V E -
W A S H E R - ^
"Punch
I N S T A L L B E A R I N G
K E Y R E L E A S E C O L U M N
• I N S T A L L L E V E R
, , A N D S P R I N G
^* 383OS103S
K E Y R E L E A S E C O L U M N
Fig. 1 1 Standard Steering Column Service (1 of 2)