Kyocera KM-C2525E Service Manual page 309

Connector Pin
YC8 27 DLP_K MOT_DR
Connected
28 DLP_K MOT_RDY
to the Inner
29 DLP_K MOT_CLK
tempera-
30 DLP_K MOT_DIR
ture sensor
3, ID sensor
1/2/3, regis-
tration
clutch and
paper feed/
developing
motor BK
YC9 1 FB_CONT
Connected 2 T1_CONT4
to the trans-
3 T1_CONT3
fer high volt-
4 T1_CONT2
age PWB 1
5 T1_CONT1
(25/25,
6 FB_REM
32/25 and
7 T1_INV_REM
32/32 ppm
models)
8 GND
9 +24V3
10 (NC)
YC9 1 FB_CONT
Connected 2 T1_CONT4
to the trans-
3 T1_CONT3
fer high volt-
4 T1_CONT2
age PWB 1
5 T1_CONT1
(40/35 ppm
6 T1_REM
model)
7 FB_REM
8 T1_HV_SET
9 GND
10 +24V3
YC10 A1 (NC)
Connected A2 GND
to main high
A3 GND
voltage
A4 +24V3
PWB
A5 +24V3
A6 DC_MAG_REM
A7 AC_MAIN_CONT2
A8 HV_CLK2
A9 DC_MAG_CONT2
A10 DC_SLV_CONT2
A11 AC_SLV_CONT2
A12 AC_MAIN_CONT1
A13 HV_CLK1
A14 DC_MAG_CONT1
A15 DC_SLV_CONT1
A16 AC_SLV_CONT1
B1 AC_MAIN_CONT4
B2 HV_CLK4
B3 DC_MAG_CONT4
B4 DC_SLV_CONT4
B5 AC_SLV_CONT4
B6 AC_MAIN_CONT3
Signal I/O
O 0/3.3 V DC
I 0/3.3 V DC
O 0/3.3 V DC (pulse)
O 0/3.3 V DC
O Analog
O Analog
O Analog
O Analog
O Analog
O 0/3.3 V DC
O 0/3.3 V DC
- -
O 24 V DC
- -
O Analog
O Analog
O Analog
O Analog
O Analog
O 0/3.3 V DC
O 0/3.3 V DC
I 0/3.3 V DC
- -
O 24 V DC
- -
- -
- -
O 24 V DC
O 24 V DC
O 0/3.3 V DC
I Analog
O 0/3.3 V DC (pulse)
O Analog
O Analog
O Analog
O Analog
O 0/3.3 V DC (pulse)
O Analog
O Analog
O Analog
O Analog
O 0/3.3 V DC (pulse)
O Analog
O Analog
O Analog
O Analog
Voltage
Paper feed/developing motor BK drive signal
Paper feed/developing motor BK ready signal
Paper feed/developing motor BK clock signal
Paper feed/developing motor BK change signal
Primary transfer cleaning bias output control voltage
Primary transfer bias control voltage (4)
Primary transfer bias control voltage (3)
Primary transfer bias control voltage (2)
Primary transfer bias control voltage (1)
Primary transfer cleaning bias: On/Off
Primary transfer bias: On/Off
Ground
24 V DC power to the transfer high voltage PWB 1
Not used
Primary transfer cleaning bias output control voltage
Primary transfer bias control voltage (4)
Primary transfer bias control voltage (3)
Primary transfer bias control voltage (2)
Primary transfer bias control voltage (1)
Primary transfer bias: On/Off
Primary transfer cleaning bias: On/Off
Transfer high voltage PWB 1 connection signal
Ground
24 V DC power to the transfer high voltage PWB 1
Not used
Ground
Ground
24 V DC power to the main high voltage PWB
24 V DC power to the main high voltage PWB
Developing magnet bias: On/Off
Main charger high voltage (AC) control voltage (2)
Developing bias clock signal (2)
Developing magnet bias (DC) control voltage (2)
Developing sleeve bias (DC) control voltage (2)
Developing sleeve bias (AC) control voltage (2)
Main charger high voltage (AC) control voltage (1)
Developing bias clock signal (1)
Developing magnet bias (DC) control voltage (1)
Developing sleeve bias (DC) control voltage (1)
Developing sleeve bias (AC) control voltage (1)
Main charger high voltage (AC) control voltage (4)
Developing bias clock signal (4)
Developing magnet bias (DC) control voltage (4)
Developing sleeve bias (DC) control voltage (4)
Developing sleeve bias (AC) control voltage (4)
Main charger high voltage (AC) control voltage (3)
2JL/2JJ/2JG/2JD-1
Description
2-3-9