Rs232C Commands Table - Pioneer PDP-V401 Technical Manual

Outer control by RS232C

5.3.3 RS232C commands table

Explanation of the tables
• Normal validity
Commands that may be used even when not in RS232C adjustment mode (after sending <AJY> commands)
• Number direct
Commands sent directly followed by numbers 000-255, which immediately become the new adjusted values.
• UP/DOWN command
Commands followed by UPn/DWn (n is any number from 0 to 9) are capable of incrementing adjustment values up
or down in increments of their values.
Command
name
A AJN ADJUST NO
AJY ADJUST YES
B BRT BRIGHTNESS
BHI BLUE HIGH
BLW BLUE LOW
BR1 BAUD RATE 1
BR2 BAUD RATE 2
BR3 BAUD RATE 3
BR4 BAUD RATE 4
BR5 BAUD RATE 5
C CM1 COLOR MODE 1
CM2 COLOR MODE 2
CNT CONTRAST
COL COLOR
CFR CLOCK FREQ.
CPH CLOCK PHASE
D DIN DISP NO
DIY DISP YES
DOF DISPLAY OFF
DW0 DOWN 10
DWn DOWN n
DWF DOWN FULL
F FRW FRESH WHITE BAL.
FRP FRESH POSITION
G GHI GREEN HIGH
GLW GREEN LOW
GWB GET W/B DATA
GPS GET POSI. DATA
GST GET STATUS
GS2 GET STATUS 2
128
<Ver. 2.1>
Validity in
Name
normal
mode
×
‡
×
×
×
×
×
×
×
×
‡
‡
×
×
×
×
‡
‡
×
×
×
×
×
×
×
×
×
×
×
×
Validity of Validity of
number- UP/
direct DOWN
command command
× ×
Exits RS232C adjustment mode (and
switches to normal operational mode).
× ×
Activates RS232C adjustment mode.
‡ ‡
Adjust BRIGHTNESS.
‡ ‡
Adjust BLUE HIGH-LIGHT.
‡ ‡
Adjust BLUE LOW-LIGHT.
× ×
Sets the RS232C baud rate to 1200bps.
× ×
Sets the RS232C baud rate to 2400bps.
× ×
Sets the RS232C baud rate to 4800bps.
× ×
Sets the RS232C baud rate to 9600bps.
× ×
Sets the RS232C baud rate to 19200bps.
× ×
Make white-balance adjustment data Mode 1.
× ×
Make white-balance adjustment data Mode 2.
‡ ‡
Adjust CONTRAST.
‡ ‡
Adjust COLOR (except for RGB 1 & 2 input).
‡ ‡
Adjust PLL frequency.
(valid only when RGB 1 & 2 are input)
‡ ‡
Adjust PLL phase.
(valid only when RGB 1 & 2 are input)
× ×
Disables OSD indication.
× ×
Enables OSD indication.
× ×
Make OSD indication OFF.
— — Make the adjustment value 10 DOWN.
— — Make the adjustment value nDOWN.
— — Minimize adjustment.
× ×
Sets all parameter values for picture quality
and white-balance within the selected memory
area 128.
× ×
Sets all values for phase adjustment within the
selected memory area 128 (valid only for
RGB 1 & 2 input).
‡ ‡
Adjusts GREEN HIGH-LIGHT.
‡ ‡
Adjusts GREEN LOW-LIGHT.
× ×
Outputs values for picture quality and white-
balance adjustment.
× ×
Outputs phase-adjustment values (valid only for RGB
1 & 2 input).
× ×
Outputs various set values.
× ×
Outputs various set values.
Function