Download  Print this page

HP ProCurve 2610-PWR Management And Configuration Manual Page 418

Procurve 2610 series procurve 2610-pwr series.
Hide thumbs
   
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464

Advertisement

Troubleshooting
Using Logging To Identify Problem Sources
For example, on a switch where there are no SyslogD servers configured, you
would do the following to configure SyslogD servers 18.120.38.155 and
18.120.43.125 and automatically enable Syslog logging (with user as the default
logging facility):
logging < syslog-ip-addr
> configures the Syslog
server(s) to use and
enables Syslog debug
logging. (In this case,
Syslog is automatically
enabled because debug
destination logging has
not been previously
disabled with other Syslog
servers already
configured in the switch.
(Refer to the Syntax box
under "Configuring the
Switch To Send Debug
Messages to One or More
SyslogD Servers" on page
C-27.)
Figure C-9. Example of Configuring and Enabling Syslog Logging
To use a non-default logging facility, such as lpr, in the same operation as in
figure C-9, you would use this command set:
ProCurve(config)# logging 18.120.38.155
ProCurve(config)# logging 18.120.43.125
ProCurve(config)# logging facility lpr
C-28
ProCurve(config)# logging 18.120.38.155
ProCurve(config)# logging 18.120.43.125
ProCurve(config)# write mem
ProCurve(config)# show config
Startup configuration:
; J9085A Configuration Editor; Created on release #R.11.XX
hostname "ProCurve Switch 2610-24"
ip default-gateway 10.0.8.1
logging 18.20.38.155
logging 18.129.43.125
snmp-server community "public" Unrestricted
vlan 1
name "DEFAULT_VLAN"
untagged 1-28
ip address dhcp-bootp
exit
ProCurve(config)# show debug
Debug Logging
Destination:
Logging - -
18.120.38.155
18.120.43.125
Facility = user
Enabled debug types:
event
The configured Syslog server
IP addresses appear in the
switch's configuration file.
This command shows that
Syslog logging is enabled for
the listed IP addresses.
Default Logging Facility

Advertisement

Chapters

Troubleshooting

   Also See for HP ProCurve 2610-PWR

   Related Manuals for HP ProCurve 2610-PWR

Comments to this Manuals

Symbols: 0
Latest comments: