094: Multitap Cho/Delay; (Multitap Chorus/Delay); 095: St. Pitch Shifter (Stereo Pitch Shifter) - Korg TRITON proX Manual

094: Multitap Cho/Delay

(Multitap Chorus/Delay)

This effect has six chorus blocks with different LFO phases.
You can produce a complex stereo image by setting a different
delay time and depth for each block. You can control the delay
output level via a modulation source.
Wet: Mono In - Stereo Out / Dry: Stereo In -Stereo Out
Left
Feedback
Tap1 Delay
Tap2 Delay
Tap3 Delay
+
Tap4 Delay
Tap5 Delay
Tap6 Delay
Right
0 [degree]
180 [degree]
60 [degree]
240 [degree]
120 [degree]
300 [degree]
LFO: Triangle
D -mod
On/Off Control
LFO Frequency [Hz]
a
Sets the LFO speed
Tap1(000) [msec]
Sets the Tap1 (LFO phase=0 degrees) delay time
Depth
b Sets the Tap1 chorus depth
Status Always On, Always Off, On→Off(dm), Off→On(dm)
Selects on, off, or modulation source for the control of Tap1 output
Tap2(180) [msec]
Sets the Tap2 (LFO phase=180 degrees) delay time
Depth
c Sets the Tap2 chorus depth
Status Always On, Always Off, On→Off(dm), Off→On(dm)
Selects on, off, or modulation source for the control of Tap2 output
Tap3(060) [msec]
Sets the Tap3 (LFO phase=60 degrees) delay time
Depth
d Sets the Tap3 chorus depth
Status Always On, Always Off, On→Off(dm), Off→On(dm)
Selects on, off, or modulation source for the control of Tap3 output
Tap4(240) [msec]
Sets the Tap4 (LFO phase=240 degrees) delay time
Depth
e Sets the Tap4 chorus depth
Status Always On, Always Off, On→Off(dm), Off→On(dm)
Selects on, off, or modulation source for the control of Tap4 output
Tap5(120) [msec]
Sets the Tap5 (LFO phase=120 degrees) delay time
Depth
f Sets the Tap5 chorus depth
Status Always On, Always Off, On→Off(dm), Off→On(dm)
Selects on, off, or modulation source for the control of Tap5 output
Tap6(300) [msec]
Sets the Tap6 (LFO phase=300 degrees) delay time
Depth
g Sets the Tap6 chorus depth
Status Always On, Always Off, On→Off(dm), Off→On(dm)
Selects on, off, or modulation source for the control of Tap6 output
Panning Preset
h
Specifies the stereo image of each Tap
202
Wet / Dry
Wet / Dry
Panning Preset
0.02...13.00Hz
0...570msec
0...30
,
0...570msec
0...30
,
0...570msec
0...30
,
0...570msec
0...30
,
0...570msec
0...30
,
0...570msec
0...30
,
1, 2, 3, 4
Tap1 Feedback
Sets the Tap1 feedback amount
Src
i Selects the modulation source for the Tap output level, feedback
amount, and effect balance
Amt
Sets the modulation amount of Tap1 feedback amount
Wet/Dry
Sets the balance between the effect and dry sounds
j
Amt
Sets the modulation amount of the effect balance
b: Status, c: Status, d: Status, e: Status, f: Status, g: Status
These parameters set the output status of each Tap.
Always On: Output is always on. (No modulation)
Always Off: Output is always off. (No modulation)
On→Off (dm): Output level is switched from on to off depending
on the modulation source.
Off→On (dm): Output level is switched from off to on depending
on the modulation source.
Combining these parameters, you can change from 4-phase cho-
rus to two-tap delay by crossfading them gradually via the modu-
lation source during a performance.
h: Panning Preset
This parameter selects combinations of stereo images of the tap
outputs.
i: Src, i: Amt, l: Amt
Tap output level, feedback amount and effect balance are con-
trolled simultaneously via a modulation source.
095: St. Pitch Shifter
This is a stereo pitch shifter. The pitch shift amount for the left
and right channels can be reversed from each other.
Stereo In - Stereo Out
Left
Pitch Shifter
Input Level
Pre
Feedback Position
Pre
Input Level
Pitch Shifter
Right
Mode
a
Switches Pitch Shifter mode
L/R Pitch
b
Determines whether or not the L/R pitch shift amount is inverted
Pitch Shift [1/2tone]
Sets the pitch shift amount in steps of a semitone
Src
c
Selects the modulation source of pitch shift amount
Amt
Sets the modulation amount of pitch shift amount
Fine [cent]
Sets the pitch shift amount in steps of one cent
d
Amt
Sets the modulation amount of pitch shift amount
Lch Delay [msec]
Sets the delay time for the left channel
e
Rch Delay [msec]
Sets the delay time for the right channel
Feedback Position
f
Switches the feedback connection
–100...+100
Off...Tempo
–100...+100
Dry, 1:99...99:1, Wet
–100...+100
(Stereo Pitch Shifter)
Wet / Dry
High Damp
Delay
Post
Feedback Spread
Post
Delay
High Damp
Wet / Dry
Slow, Medium, Fast
Fx:038
Normal, Up/Down
–24...+24
Fx:038,
Off...Tempo
Fx:038
–24...+24
Fx:038
–100...+100cent
Fx:038,
–100...+100cent
Fx:038
0...1000msec
0...1000msec
Pre, Post
Fx:038