Advertisement

014: Stereo Decimator

This effect creates a rough sound like a cheap sampler by low-
ering the sampling frequency and data bit length. You can
also simulate noise unique to a sampler (aliasing).
Stereo In - Stereo Out
Left
Pre LPF
Resolution
Decimator
D
-mod
Sampling Frequency
LFO
Decimator
Pre LPF
Resolution
Right
Pre LPF
Selects whether the harmonic noise caused by a decrease in sam-
pling frequency is generated or not
a
High Damp [%]
Sets the ratio of cut of the high range
Sampling Freq (Sampling Frequency) [Hz]
Sets the sampling frequency
Src
b
Selects the modulation source of the sampling frequency
Amt
Sets the modulation amount of the sampling frequency
LFO Frequency [Hz]
Sets the LFO speed
Src
c
Selects the modulation source of LFO speed
Amt
Sets the modulation amount of LFO speed
Depth
Sets the depth of the sampling frequency LFO modulation
Src
d
Selects the LFO modulation source of the sampling frequency
Amt
Sets the LFO modulation amount of the sampling frequency
Resolution
e
Sets the data bit length
Output Level
Sets the output level
Src
f
Selects the modulation source for the output level
Amt
Sets the modulation amount of the output level
Wet/Dry
Sets the balance between the effect and dry sounds
Src
g
Selects the modulation source of the effect balance
Amt
Sets the modulation amount of the effect balance
a: Pre LPF
If a sampler with a very low sampling frequency receives very
high-pitched sound that could not be heard during playback, it
could generate pitch noise that is unrelated to the original sound.
Set "Pre LPF" to ON to prevent this noise from being generated.
If you set the "Sampling Freq" to about 3kHz and set "Pre LPF" to
OFF, you can create a sound like a ring modulator.
e: Resolution, f: Output Level
If you set a smaller value for the "Resolution" parameter, the
sound may be distorted. The volume level may also be changed.
Use "Output Level" to adjust the level.
015: St. Analog Record
This effect simulates the noise caused by scratches and dust
on analog records. It also reproduces some of the modulation
caused by a warped turntable.
Wet / Dry
High Damp Output Level
High Damp Output Level
Wet / Dry
Off, On
0...100%
1.00k...48.00kHz
Off...Tempo
–48.00k...+48.00kHz
0.02...20.00Hz
Off...Tempo
–20.00...+20.00Hz
0...100
Off...Tempo
–100...+100
4...24
0...100
,
Off...Tempo
–100...+100
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
b: Flutter
This parameter enables you to set the depth of the modulation
caused by a warped turntable.
e: Click Level
This parameter enables you to set the level of the click noise that
occurs once every rotation of the turntable. This simulation repro-
duces record noise, and the noise generated after the music on a
vinyl record finishes.
(Stereo Analog Record)
Stereo In - Stereo Out
Left
EQ Trim
Pre EQ
Analog Record
Simulation
EQ Trim
Pre EQ
Right
Speed [RPM]
a
Sets the r.p.m. of a record
Flutter
b
Sets the modulation depth
Noise Density
Sets the noise density
c
Noise Tone
Sets the noise tone
Noise Level
Sets the noise level
Src
d
Selects the modulation source for the noise level
Amt
Sets the modulation amount of the noise level
Click Level
Sets the click noise level
Src
e
Selects the modulation source for the click noise level
Amt
Sets the modulation amount of the click noise level
EQ Trim
f
Sets the EQ input level
Pre EQ Cutoff [Hz]
Sets the EQ center frequency
Q
g
Sets the EQ band width
Gain [dB]
Sets the EQ gain
Wet/Dry
Sets the balance between the effect and dry sounds
Src
h
Selects the modulation source of the effect balance
Amt
Sets the modulation amount of the effect balance
Wet / Dry
Wet / Dry
33 1/3, 45, 78
0...100
0...100
0...100
0...100
Off...Tempo
–100...+100
0...100
,
Off...Tempo
–100...+100
0...100
300...10.00kHz
0.5...10.0
–18.0...+18.0dB
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
163

Advertisement

   Also See for Korg TRITON proX

   Related Manuals for Korg TRITON proX

This manual also for:

Triton pro

Comments to this Manuals

Symbols: 0
Latest comments: