Download Print this page

Korg TRITON proX Manual: Sequencer P8: Insert Effect

Hide thumbs

Advertisement

7–5b: Scan Zone A/B
A:
Top Key
Bottom Key
Specify the range of notes (keys) that will trigger arpeggia-
tor A. "Top Key" is the upper limit, and "Bottom Key" is the
lower limit.
Top Velocity
Bottom Velocity
Specify the range of velocities that will trigger arpeggiator
A. "Top Velocity" is the upper limit, and "Bottom Velocity"
is the lower limit.
B:
Top Key
Bottom Key
Top Velocity
Bottom Velocity
Specify the range of notes (keys) and velocities that will trig-
ger arpeggiator B ( "A").
The value of these parameters can also be input by
holding down the [ENTER] key and playing a note on
the keyboard.

Sequencer P8: Insert Effect

Here you can make insert effect settings, and specify the bus
[C–1...G9]
etc. for the program used by each track 1–16.
[C–1...G9]
For details on insert effects, refer to p.146 "8. Effect
Guide."
8–1: Routing 1–8
[001...127]
8–2: Routing 9–16
[001...127]
Specify the bus to which the program oscillator(s) of each
track 1–16 will be sent. You can also set the amount of signal
that will be sent to the master effects.
[C–1...G9]
8–1a
[C–1...G9]
[001...127]
0–1c
0–1e
0–1g
[001...127]
8–1b
8–1a: Routing Map
This shows the status of the insert effects: the insert effect
routing, the names of the selected effects, the on/off status,
and chaining. The effect type, on/off, and chain settings can
be made in the Insert FX tab.
8–1(2)b: IFX/Indiv.Out BUS Select (BUS Select),
Send1 (MFX1), Send2 (MFX2)
IFX/Indiv.Out BUS Select (BUS Select)
These settings specify the bus to which the program oscilla-
tor(s) of each track 1–16 will be sent. The status of the set-
tings can also be viewed in the "Routing Map"
( Combination P8–1: Routing).
When 1/2 or 3/4 are selected, the program of the corre-
sponding track 1–16 will be output in stereo from
AUDIO OUTPUT (INDIVIDUAL) 1 and 2 or 3 and 4. If
you use CC#10 (pan) or AMS (Alternate Modulation
Source) to control the panning of the program oscillator,
the new pan setting will be applied at the next note-on.
Unlike the case when you select L/R to output the
sound from (MAIN) L/MONO and R, the pan of a
sounding note cannot be varied in realtime.
If you wish to vary the pan of a sounding note in real-
time, and output the result from AUDIO OUTPUT
(INDIVIDUAL) 1 and 2 or 3 and 4, set "BUS Select" to
IFX1 (or IFX2–IFX5), select 000: No Effect for "IFX1"
(or IFX2–IFX5) (8–3), and select either 1/2 or 3/4 for
"BUS Select" (8–3) after the signal passes through IFX.
(Routing T01–08)
(Routing T09–16)
[DKit, L/R, IFX1...5, 1...4, 1/2, 3/4, Off]
8–1
75

Advertisement

   Also See for Korg TRITON proX

   Related Manuals for Korg TRITON proX

This manual also for:

Triton pro

Comments to this Manuals

Symbols: 0
Latest comments: