068: Comp - Phaser (Compressor - Phaser); 069: Comp - Mt. Delay; (Compressor - Multitap Delay) - Korg TRITON proX Manual

[F] Cho/Flng Wet/Dry
Sets the effect balance of the chorus/flanger
h
Output Mode
Selects the output mode for the chorus/flanger
Routing
i Switches the order of the compressor and chorus/flanger connection
Wet/Dry
Sets the balance between the effect and dry sounds
Src
j
Selects the modulation source of the effect balance
Amt
Sets the modulation amount of the effect balance
h: Output Mode, i: Routing
When Wet Invert is selected, the right channel phase of the cho-
rus/flanger effect sound is inverted. This creates pseudo-stereo
effects and adds spread.
However, if a mono-input type effect is connected after this effect,
the left and right sounds may cancel each other, eliminating the
chorus/flanger effects.
When "Routing" is set to FLNG→CMP, "Output Mode" will be
set to Normal.
068: Comp – Phaser
(Compressor – Phaser)
This effect combines a mono-type compressor and a phaser.
You can change the order of the effect connection.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
Compressor
LEQ HEQ
EQ Trim
+
Comp
Output Level
Right
Envelope - Control
[C] Sensitivity
a
Sets the sensitivity
[C] Attack
Sets the attack level
b
Output Level
Sets the compressor output level
[C] EQ Trim
c
Sets the EQ input level
[C] Pre LEQ Gain [dB]
Sets the gain of Low EQ
d
Pre HEQ Gain [dB]
Sets the gain of High EQ
[P] LFO Frequency [Hz]
Sets the LFO speed
e
LFO Waveform
Selects LFO Waveform
[P] Manual
f
Sets the frequency to which the effect is applied
[P] Depth
Sets the depth of LFO modulation
g
Resonance
Sets the resonance amount
[P] Phaser Wet/Dry
Sets the phaser effect balance
h
Output Mode
Selects the phaser output mode
190
–Wet...–2:98, Dry, 2:98...Wet
Fx:010, 020
Normal, Wet Invert
CMP → FLNG, FLNG → CMP
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
Wet / Dry
Routing
Phaser
Phaser
Normal
+
Output Mode
–
Wet Invert
Resonance
Phaser Wet / Dry
Wet / Dry
LFO: Tri / Sine
1...100
Fx:002
1...100
Fx:002
0...100
Fx:002
0...100
–15...+15dB
–15...+15dB
0.02...20.00Hz
Triangle, Sine
0...100
0...100
–100...+100
Fx:023
–Wet...–2:98, Dry, 2:98...Wet
Fx:010, 023
Normal, Wet Invert
Fx:067
Routing
i Switches the order of the compressor and phaser connection
Wet/Dry
Sets the balance between the effect and dry sounds
Src
j
Selects the modulation source of the effect balance
Amt
Sets the modulation amount of the effect balance
069: Comp – Mt. Delay
(Compressor – Multitap Delay)
This effect combines a mono-type compressor and a multitap
delay. You can change the order of the effect connection.
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
Compressor
EQ Trim LEQ HEQ
+
Right
Envelope - Control
[C] Sensitivity
a
Sets the sensitivity
[C] Attack
Sets the attack level
b
Output Level
Sets the compressor output level
[C] EQ Trim
c
Sets the EQ input level
[C] Pre LEQ Gain [dB]
Sets the gain of Low EQ
d
Pre HEQ Gain [dB]
Sets the gain of High EQ
[D] Tap1 Time [msec]
Sets the Tap1 delay time
e
Tap1 Level
Sets the Tap1 output level
[D] Tap2 Time [msec]
Sets the Tap2 delay time
f
Feedback
Sets the Tap2 feedback amount
[D] High Damp [%]
g
Sets the damping amount in the high range
[D] Mt.Delay Wet/Dry
h
Sets the multitap delay effect balance
Routing
i
Switches the order of the compressor and multitap delay connection
Wet/Dry
Sets the balance between the effect and dry sounds
Src
j
Selects the modulation source of the effect balance
Amt
Sets the modulation amount of the effect balance
CMP→PHS, PHS→CMP
Dry, 1:99...99:1, Wet
Routing
Multitap Delay
Feedback
Comp
Delay
(2)
(1)
High Damp
Mt.Dly Wet / Dry
Output Level
Dry, 1:99...99:1, Wet
CMP→DLY, DLY→CMP
Dry, 1:99...99:1, Wet
Fx:067
Off...Tempo
–100...+100
Wet / Dry
Wet / Dry
1...100
Fx:002
1...100
Fx:002
0...100
Fx:002
0...100
–15...+15dB
–15...+15dB
0...680msec
0...100
Fx:045
0...680msec
–100...+100
0...100%
Fx:043
Off...Tempo
–100...+100