hp StorageWorks ha-fabric manager user guide Part Number: AA-RS2CB-TE Second Edition (January 2003) This guide describes the HP StorageWorks High Availability Fabric Manager (HAFM), its features, and how to use it to monitor, configure, and manage the Fibre Channel in which managed products operate.
About this Guide This publication is part of a document suite that supports the Hewlett-Packard (HP) StorageWorks Director 2/64, Director 2/140, Edge Switch 2/16, Edge Switch 2/32, Edge Switch 2/24, and High Availability Fabric Manager (HAFM) application. Intended Audience This publication is intended for data center administrators, LAN administrators, operations personnel, and customer support personnel who administer user access to this application and monitor and manage product operation.
About this Guide Document Conventions The conventions included in Table 1 apply. Table 1: Document Conventions Element Convention Cross-reference links Blue text: Figure 1 Key names, menu items, buttons, and Bold dialog box titles File names, application names, and text Italics emphasis User input, command names, system...
About this Guide Symbols on Equipment Any enclosed surface or area of the equipment marked with these symbols indicates the presence of electrical shock hazards. Enclosed area contains no operator serviceable parts. WARNING: To reduce the risk of injury from electrical shock hazards, do not open this enclosure.
About this Guide Any product or assembly marked with these symbols indicates that the component exceeds the recommended weight for one individual to handle safely. WARNING: To reduce the risk of personal injury or damage to the equipment, observe local occupational health and safety requirements and guidelines for manually handling material.
About this Guide • Product serial numbers • Product model names and numbers • Applicable error messages • Operating system type and revision level • Detailed, specific questions HP Website The HP website has the latest information on this product, as well as the latest drivers. http://thenew.hp.com/country/us/eng/prodserv/storage.html.
Introduction and General Information This chapter presents an overview of the High Availability Fabric Manager (HAFM).It includes: • An introduction to using HAFM. • Information on how to access HAFM. Introduction to High Availability Fabric Management The High Availability Fabric Manager (HAFM) is a Java-based graphical user interface (GUI) that enables the user to manage users and products, monitor products, and open Product Managers.
Introduction and General Information • Management through the Internet using the EWS interface installed on the Director or Switch. This interface supports configuration, statistics monitoring, and basic operation of the product, but does not offer all the capabilities of the corresponding Product Manager application.
Introduction and General Information HAFM Server Information The HAFM server is a personal computer (PC) platform that provides a central point of control for managed Fibre Channel products. The HAFM server is required for installing, configuring, and managing these products. NOTE: Although products can perform normal operations without an HAFM server, the HAFM server should operate at all times to monitor product operations, report failures, log event changes, and log configuration changes.
Introduction and General Information Figure 1–2: High Availability Fabric Manager Login dialog box 3. In the HAFM Server field, type or choose the HAFM server to which you want to connect. If you are logging in to the local HAFM server, the HAFM server name is localhost.
Introduction and General Information 4. Click Login. The main HAFM window displays the Product View (Figure 1–3). Figure 1–3: High Availability Fabric Manager main window Menu Bar. For details, refer to Chapter 3, Using the Menu Bar. Tool Bar. For details, refer to Tool Bar on page 2-3.
Introduction and General Information Accessing Remote HAFM Servers To access remote HAFM servers, enter the server’s network address or DNS host name in the HAFM Login dialog box. If you are already logged in to the HAFM and want to access this dialog box, choose Logout from the Product menu. Figure 1–4: High Availability Fabric Manager Login dialog box 1.
Introduction and General Information Managing Remote Access to the HAFM Server Users at the HAFM server can open the HAFM and Product Managers loaded on the server itself. Users at remote PC workstations can also access the same HAFM server or other HAFM servers if the workstations meet minimum hardware and software requirements and are running the HAFM application.
Introduction and General Information Displaying Remote Sessions A maximum of nine concurrent users (eight remote and one local HAFM server user) can log in to the HAFM application. Display the current active sessions for the HAFM server that you are logged into via the User Sessions dialog box. To display the User Sessions dialog box: 1.
Page 29
Introduction and General Information When you log into Windows on the HAFM server, QuikSync starts automatically. Any data that has changed in the HAFMData directory while you were logged out will automatically be backed up. The backed up data includes: •...
Introduction and General Information Using QuikSync QuikSync is functioning to back up data when the QuikSync icon displays in the system tray in the right corner of the Windows task bar (Figure 1–6). This icon spins when data is writing to the Zip disk. Figure 1–6: QuikSync icon in Windows system tray If an icon does not display, you must enable the application using the procedure in the next section,...
Introduction and General Information 3. Click the Advanced tab. The following dialog box displays: Figure 1–7: Iomega QuikSync dialog box (Advanced tab) 4. Verify that the dialog box is configured exactly as displayed in Figure 1–7. 5. Click OK. Restore In the event of a system failure, you will be able to return your database to a known state.
Introduction and General Information 5. Restart the HAFM server: a. On the Windows taskbar, click Start > Shut Down. b. On the Shut Down Windows dialog box, click Restart the Computer and click Yes. c. When prompted, simultaneously press Ctrl+Alt+Delete to display the Logon Information dialog box.
Introduction and General Information • Logout • Exit Fabrics Menu • Rename • Persist Fabric Topology • Unpersist Fabric Topology • Export Fabric Topology • Show Route • Hide Route • Show Zone Members • Show View Port • Show Fabric Tree •...
Introduction and General Information • Center in Topology • Clear ISL Alert • Clear All ISL Alerts • Enable Fly Over Display Configure Menu • Users • Nicknames • Sessions • SNMP Agent • Activate Zone Set • Zoning Library •...
Introduction and General Information Help Menu • Contents • About Product Manager The following options are available through the Product Manager application for your Switch or Director. For more information on these options, refer to the “Menu Bar” section of Chapter 1 in the Product Manager user guide for your Switch or Director. View Tabs •...
Page 36
Introduction and General Information — Clear Threshold Alerts(s) — Display Options (Nickname and World Wide Name) • FRU (options depend on FRU selected) — Open Port Card View (Director only) — FRU Properties — Switchover (Director only) — Enable Beaconing —...
Page 37
Introduction and General Information • Addresses (S/390 mode only) — Active — Stored • SNMP Agent • Management Server (only available if a management server feature is installed) • Features • Date/Time • Threshold Alerts • Export Configuration Report • Enable Web Server •...
Introduction and General Information • Backup & Restore Configuration • Reset Configuration Help Menu • Contents • About 1–18 ha-fabric manager user guide...
Using the HAFM Window This chapter provides a description of the High Availability Fabric Manager main window, except for the menu bar, which is covered in Chapter Window Overview This section provides an over view of the HAFM main window. Illustrations Used in this Manual Figures containing HAFM and Product Manager screens are included for illustration purposes only.
Using the HAFM Window Figure 2–1: High Availability Fabric Manager main window Window Elements The HAFM main window elements are shown in Figure 2–1, High Availability Fabric Manager main window. Title Bar The title bar identifies the product. Menu Bar The menu bar provides actions for working with products, fabrics, views, configurations, logs, maintenance.
Using the HAFM Window Tool Bar The tool bar provides a number of icons for quick access to frequently used menu items, namely, commands to work with a product or to work with a fabric. Main Panel The main panel has two tabs available at the top left for choosing a view: Products or Fabrics.
Using the HAFM Window • In the Fabrics view, the Open Product icon is available when the Topology tab is selected and a product icon is selected. This button has the same functionality as choosing the Product > Open option. It allows you to open the Product Manager for a selected product.
Using the HAFM Window • Product Name — The name of the product configured through the Configure Identification dialog box in the Product Manager. • Network Address — The internet protocol (IP) address or DNS host name of the product. •...
Using the HAFM Window Export Fabric Topology Icon In the Fabrics view, the Export Fabric Topology icon (Figure 2–7) is available when the Topology tab is selected. Click the Export Fabric Topology icon to display the Export Fabric Topology dialog box. Enter a name for the .xml file in the File Name field, select a folder on your C: drive or network drive where you want to save the .xml file, and then click Save.
Using the HAFM Window Layout Icons In the Fabrics view, the Layout Icons icon (Figure 2–9) is available when the Topology tab is selected. Click the Layout Icons icon to arrange the icons in the Topology tab view area in the default layout, either circular or spring. To change the original default layout (circular), choose the Layout Icons icon, and click Spring.
Using the HAFM Window Zoom Out Icon In the Fabrics view, the Zoom Out icon (Figure 2–12) is available when the Topology tab is selected. Choose the Zoom Out icon to decrease the size of the fabric elements in the Topology tab view area. Return to the original size by choosing View >...
Using the HAFM Window Figure 2–14: Products view The Products view provides a graphical overview of all the products that you can manage and monitor through the HAFM. In a full-screen environment on an 800 x 600 resolution monitor, this panel displays up to 48 product icons. Right-click a product icon or a blank part of the view to display a pop-up menu.
Using the HAFM Window Fabrics View To access the Fabrics view, click the Fabrics tab. The Fabrics view displays, as shown in Figure 2–15, Fabrics view. Figure 2–15: Fabrics view The Fabrics view is divided into two panels. The left panel, the Fabric Tree, contains an expandable list of fabrics, products in fabrics, and nodes connected to products.
Using the HAFM Window Status Bar The products, fabrics, and HAFM status elements use the symbols in table Table 2–1 to indicate their operational state: Table 2–1: Operational States and Symbols Operational State Symbol Operational Network communication is established. All products, fabrics, and the server are operational and no failures are indicated.
Using the HAFM Window Products Status The product status box, labelled Products, indicates the operational state of the most critical product status of all the products managed by the HAFM. To find the one or more products that are causing the non-operational status, examine the product icons in the Products view.
Using the HAFM Window Double-click the icon to display a fabric log. This log displays only if the fabric has been persisted. This log reflects the time and nature of significant changes in the managed fabric. Entries contain the date/time that the change took place, the type of change, and a description of the change.
Using the Menu Bar This chapter provides a description of the following High Availability Fabric Manager menus on the menu bar: • Product • Fabrics • View • Configure • Logs • Maintenance • Help Product The Product menu displays options that are relevant to products. When the Products tab in the main panel is selected, the New option is available to display the New Product dialog box.
Using the Menu Bar 2. Click the Product menu. 3. Click the Open option. Refer to Accessing a Product Manager on page 4-7 for more information about opening a Product Manager. Delete The Delete option is only available when the Products tab is selected. To delete a product: 1.
Using the Menu Bar Properties The Properties icon is available in the Products view when you click a product icon. Click the product icon and then click the Properties icon to display the Properties dialog box for the selected product. The Properties dialog box is also available in the Fabrics view when the Topology tab is selected.
Using the Menu Bar Persist Fabric Topology Choose this option to display the Persist Fabric dialog box. Enter a name for the fabric, and click OK to “persist” the fabric. This saves a snapshot of the fabric’s current configuration (Switches, Directors, and ISLs) that displays in the Topology tab.
Using the Menu Bar Show Zone Members Choose this option to display the Show Zone Members dialog box. This dialog box displays a tree of all products in the selected fabric in the left panel. Click an icon by a product to expand the list of attached nodes.
Using the Menu Bar • Domain RSCNs — parameter available through the Configure Switch Parameters dialog box. Refer to Enable/Disable and Online State Functions on page 8-6 for more information. • Insistent Domain ID — parameter available through the Configure Switch Parameters dialog box.
Using the Menu Bar Zoom Choose the In and Out options from the Zoom option to increase and decrease the size of fabric elements. Return to the original view by selecting the Default option. Choose the Fit In View option to display the entire fabric in the view area. Note that for larger fabrics, text and icons may be difficult to see.
Using the Menu Bar Clear All ISL Alerts Choose this option to clear all ISL alerts, as shown in the Topology View. This option is not available when there are no ISL alerts. An alert only occurs in persisted fabrics when an ISL is removed from the fabric.
Using the Menu Bar By default, all users have View rights, which allow the viewing of configurations, but not the changing of configurations. View rights cannot be removed. The users with System Administrator rights can make all control and configuration changes implemented through the HAFM application.
Using the Menu Bar Table 3–1: User Rights for HAFM Functions (Continued) System Product Rights Administrator Administrator Maintenance Operator Display Options Enterprise Fabric Mode Export Fabric Topology Export Logs Fabric Zoom Persist Fabric Remote Notification Show Route Show Zone View Logs Open the Configure User Dialog Box 1.
Using the Menu Bar Figure 3–2: Configure Users dialog box Add New User Use the New User dialog box (Figure 3–3) to create new users for the HAFM. Assign a user name, a password, and certain permissions, or “rights,” to each user configured. 1.
Using the Menu Bar 3. In the User name field, enter a user name of 16 characters or less. The user name is case-sensitive. 4. In the Password box, enter a password of 16 characters or less for the new user. The password is case-sensitive.
Using the Menu Bar Figure 3–4: Modify User dialog box Modify User Parameters The Modify User dialog box (Figure 3–4) is used to change the password, description, and rights for those users already configured in the HAFM. 1. In the Password field, delete the current password and enter another password of 16 characters or less.
Using the Menu Bar Delete User Delete users from the system through the Configure Users dialog box (Figure 3–2 on page 3-11). 1. From the Configure menu, choose Users. The Configure Users dialog box displays (Figure 3–2 on page 3-11). 2.
Using the Menu Bar Figure 3–6: Configure Nicknames dialog box The left column in the dialog box shows the selected WWN, while the right column shows the assigned nickname. 2. Click New to add a new nickname. The Add Nickname dialog box displays (Figure 3–7).
Using the Menu Bar c. In the World Wide Name column, enter the 8-byte World Wide Name, in the standard format. For example, 10:00:08:00:88:40:20:B1 d. In the right column, enter the nickname you want to assign. e. Click OK. 4. To add an attached node (node currently connected to a product port): a.
Using the Menu Bar 5. Click OK to close the Configure Nicknames dialog box. To delete a nickname: 1. In the Configure Nicknames dialog box, select the nickname that you want to delete (Figure 3–6 on page 3-15). 2. Click Delete. 3.
Page 70
Using the Menu Bar 2. Click the Allow remote management sessions check box (a check mark displays) to allow remote access from remote workstations. If you do not choose this option, remote access is blocked even if you provide access information in other parts of this dialog box.
Using the Menu Bar SNMP Agent Choose the SNMP Agent option to open the Configure SNMP dialog box that allows you to configure the SNMP agent that runs on the HAFM server and implements the Fibre Alliance MIB. The HAFM server software contains a simple network management protocol (SNMP) agent component.
Using the Menu Bar 2. Click in the Community Name column and enter the SNMP community name for a trap recipient. This name defines the community name that SNMP managers use for reading variables from or writing variables to the HAFM server. This name must be 64 characters or less.
Using the Menu Bar Zoning Library Opens the Zoning Library dialog box. Use this dialog box to perform the major tasks for configuring zoning on the fabric: • Configure zone sets by combining zone members (attached nodes) • Configure zone sets by combining zones •...
Using the Menu Bar Logs Sorting log entries is the same for all logs. Sort log entries in columns by clicking a column heading. For columns that contain text, the columns are sorted alphabetically. For columns with data, such as date and time, the columns are sorted by date. The default view for all logs is to show the most current event based on date and time when the event occurred.
Using the Menu Bar Maintenance The Maintenance menu provides tools for setting remote communication options. Configure E-Mail Configure up to five e-mail addresses for administrators or others who should be notified of significant product events. The events that initiate e-mail notification are specific to each managed product.
Using the Menu Bar 4. To enable or disable e-mail notification, choose the Enable E-Mail Event Notification check box. 5. This will enable e-mail notification for all Product Managers if e-mail notification is enabled through each Product Manager’s Enable E-Mail Notification option. If the Enable E-Mail Event Notification check box is not selected, e-mail notification is disabled for all Product Managers.
Using the Menu Bar You can check remote notification for one or both remote communication methods. 2. To test the call-home feature, click the Call Home check box. 3. To test the e-mail notification feature, click the E-Mail check box. 4.
Using the Menu Bar 4. Click OK to accept and activate the data. If e-mail notification is also enabled, an e-mail will be sent if the HAFM cannot communicate with a product. If call-home notification is also enabled, a call-home notification will be generated if the HAFM cannot communicate with a product.
Using the Products View This chapter provides information to help you use features in the Products tab. Overview Display the Products view by clicking the Products tab on the High Availability Fabric Manager window. This is the default tab for the HAFM. It displays icons of all products, such as Switches and Directors, that you can manage through the HAFM and Product Manager applications.
Using the Products View Product Icon Display The Products view can display up to 48 product icons. Use the scroll bar to display any icons that are out of view. The view in Figure 4–1 displays Director and Edge Switch product icons. You can also determine the product represented by the icon by right-clicking the icon and choosing Properties or double clicking the icon to display the product’s HAFM Properties dialog box.
Using the Products View • Status indicator. This is the colored symbol behind the product’s illustration in the icon. — A blinking red and yellow diamond means that the product has failed and requires immediate service. — A yellow triangle means that the product is degraded, but is still performing as designed.
Using the Products View Choose this option to display the New Product dialog box. Use this dialog box to identify a product to the HAFM and add its icon to the Product view. Figure 4–3: New Product dialog box 1. Enter a valid IP address or domain name server (DNS) host name in the Network Address field.
Using the Products View Sort Options This option displays additional options for displaying product icons. • By Name — Arrange icons alphabetically, by product name. • By Severity — (Default). Arrange icons according to the product’s operating status. Failed products appear first, followed by products with degraded, then unknown, then fully operational status.
Using the Products View Delete 1. Choose this option to delete the product from the Products view. 2. When a Warning dialog box displays asking if you want to remove the item from the system, click Yes. The product icon is deleted from the Products view. CAUTION: Deleting a product from the Products view removes all information about the product from the system.
Using the Products View The Switch or Director Properties dialog box displays information about a product managed by the HAFM including the following: • Name of the product as configured through the Configure Identification dialog box in the Product Manager application. •...
Using the Products View Figure 4–6: Director 2/64 Product Manager window The Product Manager provides several views for managing and monitoring individual Fibre Channel devices, including the Hardware, Node List, Port List, Performance, and FRU List views. Through the Product Manager Hardware view, for example, you can determine status and control operation of individual hardware components.
Using the Products View • Download firmware. • Perform other configuration and monitoring tasks specific to the product. NOTE: A maximum of eight remote users (in addition to the local HAFM server user) can concurrently access Product Managers for a specific product. The HAFM window is still available as a separate window when a Product Manager is open.
Using the Products View Available Menu Bar Options The following options are active only in the Products view. For information on other menu options, refer to Chapter 3, Using the Menu Bar. Product Menu New — Choose this option to display the New Product dialog box. Use this dialog box to identify a product to the HAFM and add its icon to the Products view.
Using the Fabrics View This chapter provides information to help you use the Fabrics view in the High Availability Fabric Manager window. Overview Access the Fabrics view by clicking the Fabrics tab on the HAFM window. The left panel of this view is the Fabric Tree, which is the expandable list of fabrics, products in fabrics, and nodes connected to products.
Using the Fabrics View Topology Tab The view area of the Topology tab provides details on all fabrics known to the HAFM server and HAFM application. This area displays product icons like those in the Products view, each representing Switches and Directors in fabrics that you select from a Fabric Tree on left panel of the view.
Using the Fabrics View Figure 5–2: Fabrics view — Zone Sets tab Fabric Tree The scrollable panel on the left side of the Topology and Zone Set tabs contains a list of fabrics that you can select for display of information or to perform actions on in the left panel of the Topology and Zoning tabs.
Using the Fabrics View Click the button to the left of the product WWN or nickname to display all nodes, such as servers or storage devices, attached to the product. Status is not available for the nodes. Colored status symbols display before fabric names, if the fabrics are “persisted,” and before product names or product WWNs.
Using the Fabrics View Product Colored icons reflecting the product status display before each Switch or Director at all times. • A blinking red and yellow diamond means that the product has failed and requires immediate service. • A yellow triangle means that the product is degraded, but is still performing as designed.
Using the Fabrics View Unpersist Fabric Topology This option displays only if a fabric has been persisted. Choosing this option will display a warning that the fabric log will be lost if the fabric is unpersisted. Click Yes to unpersist the fabric and the current view of the fabric displays in the tab’s view area without the fabric status indicators.
Using the Fabrics View Product Pop-Up Menu Right-click a product WWN or name (if configured through the Configure Nicknames dialog box) to display a pop-up menu of options. Open Click this to open the Product Manager for the selected product (Figure 5–4).
Page 96
Using the Fabrics View • Control the system error indicator light emitting diode (LED) and beaconing operation for other product LEDs. • Enable an initial program load (IPL). • Download firmware. • Perform other configuration and monitoring tasks specific to the product. NOTE: A maximum of eight remote users (in addition to the local HAFM server user) can concurrently access Product Managers for a specific product.
Using the Fabrics View Node Pop-Up Menu Right-click a node’s WWN or name (if configured through the Configure Nicknames dialog box) to display a pop-up menu of options. Properties Click to display the Node Properties dialog box. Figure 5–5: Node Properties dialog box This dialog box contains the following information: •...
Using the Fabrics View The dialog box displays a list of product and node WWNs in the left panel and the assigned nicknames in the right panel. Use the New button to assign new nicknames for WWNs; use the Delete button to delete nicknames. Modify the nickname by clicking by the nickname in the dialog box and changing the name.
Using the Fabrics View Product Icon Right-click a product icon in the Topology view area to display the following menu options: • Open. Click to open the Product Manager application for the product. You can also choose this option from the product pop-up menu by right-clicking a product name in the Fabric Tree.
Using the Fabrics View View Area Right-click a blank area in the Topology view area, away from an ISL line or product icon, to display the following menu options: • Clear All ISL Alerts. Click to clear all ISL alerts (yellow triangles) from the view of the persisted fabric.
Using the Fabrics View Adjusting the Fabric Display You can manipulate the fabric in the tab’s view area for a better display, especially of larger fabrics by clicking and dragging the fabric in the view area, using menu options, and using options on the tool bar at the top of the HAFM window. You can use these methods to adjust the view: •...
Using the Fabrics View — Choose the Fit In View option to display the entire fabric in the view area. Note that for larger fabrics, text and icons may be difficult to see. Choose Default from the Zoom menu to return to the original view or use the Out option to selectively reduce the view.
Using the Fabrics View Figure 5–7: Persisted fabric in Topology view Graphic Indicators in View Changes to a persisted fabric are indicated in the Topology view area as the following: • If a Switch or Director is removed from or added to the fabric, the product displays in a dimmed state and ISL(s) that connected the product to the fabric will appear as dashed yellow lines.
Using the Fabrics View • If an ISL is added, the ISL displays as a black line with an alert indicator (yellow triangle). If you persist the fabric again, a product displays in the view if added and disappears from the view if removed. Added ISL lines remain in black and yellow-dashed ISL lines disappear.
Using the Fabrics View — Failed — Fabric has split into two or more fabrics. — Unknown — No information is known about the fabric. Note that this status is also reflected by colored icons by the fabric name in the Fabric Tree (refer to Status Icons on page 5-4).
Using the Fabrics View Logout Click this to log out of the current session, close the HAFM, and close any open Product Managers. The HAFM Login dialog box displays and allows you to log in to another HAFM server. Exit Exits the HAFM application.
Page 107
Using the Fabrics View You can open this file and read its contents using any ASCII editor, such as Notepad. Information is grouped under the WWN of each fabric member (Switch or Director). Information includes: • WWN and domain ID of the Switch or Director. •...
Using the Fabrics View • All Switches or Directors in the route must be Director 2/140, Director 2/64, Edge Switch 2/32, Edge Switch 2/24, Edge Switch 2/16, or other models that support Show Route and must be running firmware version 1.3 or higher. •...
Using the Fabrics View Figure 5–9: Route displayed in Topology tab The route between the nodes and through the products display as a thick blue line between two node icons. Right click the line to display the following menu options: •...
Using the Fabrics View Show Zone Members Click to display the Show Zone Members dialog box. This dialog box displays a tree of all products in the fabric in the left panel. Click an icon by a product to expand the list of attached nodes.
Using the Fabrics View View Choose the View menu on the menu bar to display the following options: User Sessions Click this to display the User Sessions dialog box. This lists sessions with the HAFM server from remote workstations. The dialog box lists user names, remote workstation address, and the date/times that users established a connection.
Using the Fabrics View Enable Fly Over Display Enable the fly-over display of product identification and the number of ISLs between products when you move the cursor over elements in the view area by selecting the check box. Disable the fly-over display by clearing the check mark. Configure Choose the Configure menu on the menu bar to display the following options: Users...
Page 114
Using the Fabrics View When configuring SNMP, you can configure just the community names of valid SNMP management stations. For details on using the Configure SNMP dialog box, refer to SNMP Agent on page 3-19. Activate Zone Set Opens the Activate Zone Set dialog box that allows you to select and activate configured zone sets.
Using the Fabrics View Advanced Zoning Choose this option to open a secondary menu with the following options: • Deactivate Zone Set. Click this option to display the Deactivate Zone Set dialog box. Use this dialog box to deactivate the current active zone set. Click Start to begin the process, and messages display to indicate deactivation status.
Using the Fabrics View Persist Fabric Topology Click to persist the current fabric configuration. If the fabric is not persisted already, the Persist Fabric Topology dialog box displays so that you can enter a name for the fabric. Refer to Persistent Fabrics on page 5-14.
Using the Fabrics View Fit Topology in View This option is also available in the Zoom secondary menu under the View menu on the menu bar. This displays the entire fabric in the view area. This enlarges elements of smaller fabrics and reduces elements of large fabrics. Note that for larger fabrics, text and icons may be difficult to see.
Using the Fabrics View — The Default Zone is DISABLED. If disabled, members of the default zone will not appear in the tree structure in the display area. — The active zone set does not currently match any of the stored zone sets.
Fabric Zoning This chapter explains how to: • Zone fabrics • Use zoning features and dialog boxes Zoning Basics NOTE: Designing zoning can be a complex task, especially for multiswitch fabrics. Refer to HP’s professional services organization before configuring zoning. This section is designed to help you understand the following concepts so that you can more efficiently use HAFM features to configure and manage zones across a multiswitch fabric:...
Fabric Zoning • Establish barriers between devices that use different operating systems. For example, it is often critical to separate servers and storage devices with different operating systems because accidental transfer of information from one to another can delete or corrupt data. Zoning prevents this accidental transfer of information by grouping devices that use the same operating systems into zones.
Fabric Zoning Figure 6–2 illustrates how zones can consist of ports and/or devices installed on ports in three managed products in a multiswitch fabric. Zone 1 Zone 2 Zone 3 Interswitch Link Director Director Director Figure 6–2: Zoning through a multiswitch fabric ha-fabric manager user guide 6–3...
Fabric Zoning Controlling Access at the Switch A port binding feature is available on Switches and Directors that allows you to “bind” a specific Switch or Director port to the WWN of an attached device for exclusive communication. This WWN binding feature is available through the Configure Ports option in the Product Manager application’s Configure menu.
Fabric Zoning Access can also be controlled at the storage device as an addition or enhancement to redundant array of independent disks (RAID) controller software. Data access is controlled within the storage device, and server HBA access to each LUN is explicitly limited (access is blocked by default).
Fabric Zoning Zones A zone comprises a set of members that can access each other. Refer to Table 6–2 on page 6-12 for details on the number of members that you can configure in a zone and the number of zones that you can configure in the HAFM zoning library. A zone member can be a product port or the WWN of the device.
Fabric Zoning Using Port Numbers To identify a zone member by port number, use the domain identification number of the managed product and the port number on that managed product. For example: Domain 1, Port 1 NOTE: Port numbers cannot be used for zone members if the interoperability mode for the Switch or Director is set to Open Fabric 1.0 mode.
Fabric Zoning Zone Sets A zone set is a group of zones that you can activate or deactivate as a single entity across all managed products in either a single Switch or a multiswitch fabric. Only one zone set can be active at one time. Devices that are members of zones in the zone set can only communicate with members of zones in the same zone set.
Fabric Zoning Configurations of Merged Zoned Fabrics When fabrics join through an ISL, adjacent managed products exchange active zone configurations and determine if the configurations are compatible and can merge. If the configurations can merge, the fabrics join. The resulting configuration will be a single zone set containing zone definitions from each fabric.
Fabric Zoning Table 6–1: Merging Fabrics — Results for Zone Configurations Fabric A Fabric B Result Not zoned Not zoned Fabrics join successfully. The new fabric remains not zoned. Not zoned Zoned Fabrics join successfully and the active zone set will propagate across the fabric.
Fabric Zoning Configuring Zoning through the HAFM This section provides procedures for using the menu options available through the HAFM Fabrics tab to configure and manage zoning. For information on other menu options, refer to Chapter 3, Using the Menu Bar.
Fabric Zoning Use this dialog box to perform major tasks for configuring zoning on the fabric: • Display zone sets, zones, and zone members in library • Configure zones by adding zone members (attached nodes) • Configure zone sets by adding zones •...
Fabric Zoning Menus The following menus and options are available in the Zoning Library dialog box. Page numbers are provided for procedures in using these options. Options under specific menus may only be enabled or perform different functions depending on whether the Zones or Zone Sets tab is selected.
Fabric Zoning Menu Menu Option Procedures Right-click menu Delete Delete Zones and Zone Sets, (zoning library) page 6-21 Right-click menu Properties Display Zone and Zone Set (zoning library) Properties, page 6-22 Display Configured Zone Sets and Zones Click the Zone Sets tab (default) to display all configured zone sets. Click the Zones tab (default) to display all configured zones.
Fabric Zoning Figure 6–4: New Zone dialog box NOTE: The icon that you click to expand the list of ports may not appear by a domain where no nodes attached to ports. 7. Add members to the new zone using the following steps: a.
Fabric Zoning b. Click a node or port in the expanded list to highlight it. To select multiple members individually, press Ctrl and click members. To select multiple members in order, press Shift and click the first and last members of the group you want to move.
Fabric Zoning 10. Either click World Wide Name and enter a valid 16-digit WWN or click Nickname and enter a configured nickname for the WWN into the corresponding field. (Note that the nickname must have been configured through the Configure Nicknames dialog box first.) 11.
Fabric Zoning Figure 6–7: New Zone Set dialog box Configured zones should display in the Zones in Library area. If zones do not display, you must first configure zones before you can configure any zone sets. To view members in the zones displayed, click a zone to select it, then click View Members at the bottom of the Zones in Library field.
Fabric Zoning Figure 6–8: New Zone Set dialog box — Adding Zones 7. To accept the zone set, click OK. The New Zone Set dialog box closes and the new zone set displays in the Zone Set tab of the Zoning Library dialog box. Modify Zones and Zone Sets Use the following procedures to modify existing zones and zone sets using the Open option in the File menu.
Fabric Zoning Zone Sets 1. Choose the Zone Sets tab in the Zoning Library dialog box. 2. Click a zone set to select it in the library. 3. Click File > Modify. The Modify Zone Set dialog box displays. 4. Use steps, starting with Step 5 under Configure Zone Sets on page 6-17, to view zone members or add or remove zones from zone sets.
Fabric Zoning Delete Zones and Zone Sets Zones 1. Choose the Zones tab in the Zoning Library dialog box. 2. Click a zone to select it and choose File > Delete, or right-click the zone and choose Delete from the pop-up menu. 3.
Fabric Zoning Import and Export Zone Sets While using the Zone Sets tab, use these options from the File menu to export a zone set as an .xml file and import the zone set into another zoning library. Note that you cannot import the zone set if it contains zones that are already in new zoning library.
Fabric Zoning Zones 1. Choose the Zones tab in the Zoning Library dialog box. 2. Click a zone to select it and choose File > Properties, or right-click the zone and choose Properties from the pop-up menu. The Zone Properties dialog box displays (Figure 6–9).
Fabric Zoning Figure 6–10: Zone Set Properties dialog box The dialog box summarizes the number of zones and unique zone members in the zone set. The Zone Set Library, consisting of the zone set, its zones, and zone members, are displayed in a tree structure in the Zones In Set display area. Click the icon to the left of the zone set folder to expand the list of zones in the set.
Fabric Zoning 5. Perform one of the following tasks: • Click OK to remove the zone from the selected zone set. • Click the All Zone Sets radio button, then OK to remove the zone from all zone sets in the library. Find Zone Members Use this option to find zones where a zone member’s WWN or nickname (if configured) is located.
Fabric Zoning 6. Perform one of the following tasks: • Click OK to remove the member from the selected zone • Click the All Zones button to remove the member from all zones in the library and click OK. 7. To replace the member in a specific zone with another member: a.
Fabric Zoning 3. Open the Activate Zone Set dialog box (Figure 6–12) by choosing Configure > Activate Zone Set. The dialog box displays all zone sets currently configured for the fabric. Figure 6–12: Activate Zone Set dialog box 4. Click a zone set to select it. 5.
Fabric Zoning Figure 6–13: Activate Zone Set (Differences) screen Determine which zones will be added and removed when the previous zone set is replaced with the new zone set by the icons and text color displayed in the expanded list of zone names. Table 6–4: Icons and Text Indicators for Zone Set Differences Icon Zone Name Text Color...
Fabric Zoning 6. Click Next. An Activate Zone Set screen (Figure 6–14 on page 6-29) displays, listing the Directors and Switches affected by the change in active zone sets. The Switch/Director domain ID displays in the left panel and the WWN displays in the right panel.
Fabric Zoning Deactivate Zone Sets To deactivate zone sets: 1. Select the fabric in the Fabric Tree area for which the zone set is to be deactivated. 2. Choose Configure > Deactivate Zone Set (Advanced Zoning submenu). The Deactivate Zone Set dialog box displays. Use this dialog box to deactivate the current active zone set.
Fabric Zoning Show Zone Members To show zone members: 1. Select the fabric in the Fabric Tree area for which zone members are to be shown. 2. Click the Fabrics > Show Zone Members to display the Show Zone Members dialog box.
HAFM Logs This chapter contains information on the High Availability Fabric Manager logs. Using Logs The Audit, Session, Product Status, and Fabric Logs store up to 1000 entries each. The most recent entry displays at the top of the log. After 1000 entries are stored, new entries overwrite the oldest entries.
HAFM Logs • Refresh Click Refresh to update the display. • Close Click Close to close the log. Expanding Columns Expand columns in logs by placing the pointer over the line separating column headings until a double arrow displays, then drag the line to widen the column as necessary.
HAFM Logs • The Event column describes the action that took place. Logged actions could include: — Defining a new product — Modifying product attributes — Deleting product definitions — Defining a new user — Modifying user administration — Deleting user administration —...
HAFM Logs To display the Event Log, choose Logs > Event Log. The Event Log displays (Figure 7–2). Figure 7–2: High Availability Fabric Manager Event Log • The Date/Time column logs the date and time the event was reported to the HAFM server.
HAFM Logs High Availability Fabric Manager Session Log The HAFM Session Log provides the date/time, user name, and network address of each login and logout on the HAFM server. To display the Session Log, choose Logs > Session Log. The Session Log displays (Figure 7–3 on page 7-5).
HAFM Logs High Availability Fabric Manger Product Status Log The HAFM Product Status Log reflects the time and nature of significant events on all managed products, and indicates which specific Product Manager applications should be opened to further investigate product status changes. To display the Product Status Log, choose Logs >...
HAFM Logs High Availability Fabric Manager Fabric Log The HAFM Fabric Log reflects the time and nature of significant changes in the managed fabric. To display the Fabric Log, choose Fabric Log from the Logs menu or double click the Fabrics icon on the HAFM status bar.
HAFM Logs List Drive Go Up One Level Home Details Create Folder Figure 7–6: Save dialog box 2. In the Save dialog box, browse to the folder where you want to save the file. 3. Type a file name and extension in the File name field. 4.
Optional Features This chapter provides detailed information on using, administering, and configuring optional HAFM features through HAFM applications. There are two types of features covered in this chapter: • “Keyed” features, requiring feature keys to be purchased and enabled through the Configure Feature Key dialog box in the product’s Product Manager application.
Page 160
Optional Features • Switch Clock Alert Mode Click this check box to display a check mark and enable clock alert mode. If this is enabled, the following occurs when users set the date and time through the Configure Date and Time dialog box (Configure menu): —...
Optional Features • Code Page Consider the language required for the port name display that displays on the HAFM Server. Language support is provided through character set 697 for all Extended Binary-Coded Decimal Interchange Code (EBCDIC) pages. When planning the installation, select the EBCDIC code page for displaying host-assigned port names or the CUP name.
Optional Features Procedure To configure the FICON management server, use the following steps: 1. Choose Configure > Management Server from the Product Manager window. The Configure FICON Management Server dialog box displays, as shown in Figure 8–1. Figure 8–1: Configure FICON Management Server dialog box 2.
Optional Features Installation To install and enable this option, choose the Configure Feature Key option on the Product Manager Configure menu. Configuring the Open Systems Management Server Use these procedures to configure the open systems inband management program to function with the Switch. The optional Open Systems Management Server feature must be installed in order to perform this procedure.
Optional Features SANtegrity Features SANtegrity includes a set of features that enhance security in SANs (Storage Area Networks) that contain a large and mixed group of fabrics and attached devices. Through these features you can allow or prohibit Switch attachment to fabrics and device attachment to Switches.
Optional Features Switch Binding This feature is managed through the Switch Binding submenu options available on the Product Manager Configure menu. Using Switch Binding, you can specify devices and Switches that can attach to Director and Switch ports. This provides security in environments that include a large number of devices by ensuring that only the intended set of devices attach to a Switch or Director.
Optional Features Enable/Disable Switch Binding 1. Choose the Configure > Switch Binding > Change State from the Product Manager window. The Switch Binding State Change dialog box displays, as shown in Figure 8–3. Figure 8–3: Switch Binding State Change dialog box 2.
Optional Features 4. Click Activate to enable the changes and close the dialog box. 5. Edit the Switch Membership List through the Switch Binding Membership List dialog box to add or remove Switches and devices that are allowed to connect with the Switch.
Optional Features 3. Click Nickname, then click OK. 4. To prohibit connection to a Switch port from a WWN currently in the Membership List, click the WWN or nickname in the Membership List, then click Remove. The WWN or nickname will move to the Node List panel. WWNs can only be removed from the fabric if any of the following is true: •...
Optional Features • You cannot disable Switch Binding if Enterprise Fabric Mode is enabled. • If Enterprise Fabric Mode is enabled and the Director or Switch is online, you cannot disable Switch Binding. However, if Enterprise Fabric Mode is disabled, you can disable Fabric Binding, Switch Binding, or both.
Optional Features Enterprise Fabric Mode Enterprise Fabric Mode is an option available on the Fabrics menu in the HAFM application if the SANtegrity feature key is installed. This option automatically enables the following features and operating parameters that are necessary in multiswitch Enterprise Fabric environments.
Optional Features Domain RSCNs This is a parameter in the Configure Switch Parameters dialog box, available from Configure menu in the Product Manager application. Domain register for state change notifications (domain RSCNs) are sent between end devices in a fabric to provide additional connection information to host bus adapters (HBA) and storage devices.
Information and Error Messages This appendix describes messages that may appear as you use the High Availability Fabric Manager. A description and action are provided for each message, which is listed in alphabetical order. Table A–1: High Availability Fabric Manager Messages Message Description Action...
Page 174
Information and Error Messages Message Description Action Are you sure you want The selected product will be Click Yes to delete the to delete this product? deleted from the list of product or No to cancel product definitions. the operation. Are you sure you want The selected user will be Click Yes to delete the...
Page 175
Information and Error Messages Message Description Action Cannot disable Fabric You attempted to disable Disable Enterprise Fabric Binding while Fabric Binding through the Mode through the Enterprise Fabric Mode Fabric Binding dialog box, Enterprise Fabric Mode is active. but Enterprise Fabric Mode dialog box in HAFM was enabled.
Page 176
Information and Error Messages Message Description Action Cannot have spaces in Spaces are not allowed as Delete spaces from the field. part of the entry for this field entry. field. Cannot modify a zone A zone set must have a Assign a valid name to set with an invalid valid name to be modified.
Page 177
Information and Error Messages Message Description Action Cannot retrieve current The current SNMP Try again. If the problem SNMP configuration. configuration could not be persists, contact the next retrieved. level of support. Cannot save SNMP The current SNMP Try again. If the problem configuration.
Page 178
Information and Error Messages Message Description Action Default zoning is not A default zone cannot be Change the interop supported in Open enabled when the product is mode from Open Fabric Fabric Mode. enabled for Open Fabric mode to Homogeneous mode.
Page 179
Information and Error Messages Message Description Action Duplicate World-Wide A World Wide Name can be Modify (to make it Name in nickname associated with only one unique) or delete the configuration. nickname. selected World Wide Name. Duplicate zone in zone More than one instance of a Delete one of the set configuration.
Page 180
Information and Error Messages Message Description Action Enabling this zone set Only one zone set can be Click OK to continue or will replace the active. By enabling the Cancel to end the currently active zone selected zone set, the operation.
Page 181
Information and Error Messages Message Description Action Fabric Log will be lost When you unpersist a Click Yes to unpersist the once the fabric fabric, the corresponding fabric or No to cancel the unpersists. Do you want fabric log is deleted. operation.
Page 182
Information and Error Messages Message Description Action Invalid port number. You have specified an Specify a valid port Valid ports are invalid port number. number, in the range 0 to (0-< nn >). the maximum number of ports on the product minus 1.
Page 183
Information and Error Messages Message Description Action Invalid World Wide The World Wide Name or Try the operation again Name or nickname. nickname that you have using a valid World Wide specified is invalid. The Name or nickname. valid format for the World Wide Name is eight two-digit hexadecimal numbers separated by...
Page 184
Information and Error Messages Message Description Action No nickname selected. No nickname was selected Choose a nickname and when the command was try again. attempted. No Product Managers No Director or Switch Install the appropriate installed. Product Manager Product Manager to this application is installed on workstation.
Page 185
Information and Error Messages Message Description Action No zone set selected. A zoning operation was Choose a zone set and attempted without a zone try the operation again. set selected. Only attached nodes Users cannot display Change the add criteria can be displayed in this unused ports when adding to Add by Port.
Page 186
Information and Error Messages Message Description Action Selection is not a World The selection made is not a Choose a valid World Wide Name. World Wide Name. Wide Name before performing this operation. HAFM Server shutting down. application is Reboot the HAFM closing and terminating server.
Page 187
Information and Error Messages Message Description Action The maximum number The maximum number of Close a Product of open products has open products allowed was Manager session already been reached. reached. (existing open product) before opening a new session. The maximum number The number of managed Delete an existing of products has already...
Page 188
Information and Error Messages Message Description Action The maximum number The maximum number of Delete an existing zone of zones per zone set zones that can be defined in before adding a new has already been a zone set to the HAFM zone to the zone set.
Page 189
Information and Error Messages Message Description Action This network address The specified IP address Consult with the has already been was assigned and customer’s network assigned. configured. A unique administrator to address must be assigned. determine a new IP address to be assigned and configured.
Page 190
Information and Error Messages Message Description Action You must define an A simple mail transfer Define the SMTP server SMTP server address. protocol (SMTP) server address at the address must be defined Configure E-Mail dialog and configured for e-mail to box.
Configuring Remote Workstations: Windows Systems This section describes the procedures for installing the high availability fabric manager on a remote workstation running Windows 95, Windows 98, Windows 2000, or Windows XP. To run the High Availability Fabric Manager on a remote workstation, you must first download and install the High Availability Fabric Manager application from the HAFM server.
Configuring Remote Workstations: Windows Systems • Java-enabled Internet browser, such as Microsoft Internet Explorer (version 3.0 or later) or Netscape Navigator (version 3.0 or later). Newer versions of the High Availability Fabric Manager or Product Managers installed on the HAFM server will automatically download when the remote clients log in to the server.
Configuring Remote Workstations: Windows Systems Figure B–1: Remote Client Installation screen 1. On the page, click Begin Windows Installation to begin the installation process. A security warning page prompts you to install the InstallAnywhere Web Installer (Figure B–2). Figure B–2: Security Warning page ha-fabric manager user guide B–3...
Configuring Remote Workstations: Windows Systems 2. If you have read the security agreement information and wish to continue, click Yes. The HP High Availability Fabric Manager (HAFM) InstallAnywhere Web Installer page displays. Figure B–3 illustrates a portion of this page. Figure B–3: InstallAnywhere Web Installer page 3.
Configuring Remote Workstations: Windows Systems Figure B–4: High Availability Fabric Manager Installer — Introduction screen 4. Click Next. At any time, you may return to the previous page by clicking Previous or quit the Installer by clicking Exit. The License Agreement screen displays (Figure B–5 on page B-6).
Configuring Remote Workstations: Windows Systems Figure B–5: High Availability Fabric Manager Installer — License Agreement 5. If you have read the license agreement and agree to accept the terms, click I accept the terms of the License Agreement. Click Next. The Important Information screen displays (Figure B–6).
Configuring Remote Workstations: Windows Systems 6. Click Next. (Figure The Choose Install Folder screen displays B–7). Figure B–7: High Availability Fabric Manager Installer — Choose Install Folder 7. Select a folder on the remote workstation in which to store the HAFM software. You can accept the default location, type in the path to a new location, or click Choose to browse for an appropriate location.
Configuring Remote Workstations: Windows Systems Figure B–8: High Availability Fabric Manager Installer — Choose Shortcut Location 9. Select a shortcut location. The options for the location of High Availability Fabric Manager icons are: • In a new Program Group—Adds a new program group on the Start menu for the High Availability Fabric Manager.
Configuring Remote Workstations: Windows Systems The Create Icons for All Users check box can be enabled for some of the shortcut options but not all. If the check box is enabled, the appropriate High Availability Fabric Manager icons are placed on the desktop and in the Programs folder of every Windows user.
Configuring Remote Workstations: Windows Systems Figure B–10: Installing HP HAFM (Figure 12. When complete, the following screen displays B–11). Click Done to close the Install Complete dialog box. Figure B–11: High Availability Fabric Manager Installer — Install Complete B–10 ha-fabric manager user guide...
Configuring Remote Workstations: Windows Systems Running the High Availability Fabric Manager 1. If you chose icons to be created in step 9 of the installation procedure, access the icon installed in the windows Start menu or desktop to run HAFM. 2.
Configuring Remote Workstations: Solaris Systems This section describes the procedures for installing the High Availability Fabric Manager on a remote Solaris workstation. To run the High Availability Fabric Manager on a remote workstation, you must first download and install the High Availability Fabric Manager application from the HAFM server.
Configuring Remote Workstations: Solaris Systems Procedure To install the High Availability Fabric Manager on a remote workstation: 1. Open a World Wide Web (WWW) browser. 2. Type the address of the HAFM server in the Location (or Address) field of the browser, then press Enter.
Configuring Remote Workstations: Solaris Systems 3. On the page, click Begin Solaris Installation to begin the installation process. A security warning page prompts you to install the InstallAnywhere Web Installer (Figure C–2). Figure C–2: Security Warning page 4. If you have read the security agreement information and wish to continue, click Yes.
Page 206
Configuring Remote Workstations: Solaris Systems 8. Click Next. The Choose Install Folder screen displays (similar to Figure B–7 on page B-7). 9. Choose a folder on the remote workstation in which to store the HAFM software. You can accept the default location, type in the path to a new location, or click Choose to browse for an appropriate location.
Configuring Remote Workstations: Solaris Systems Running the High Availability Fabric Manager Run the High Availability Fabric Manager program from the directory in which you saved it (the default is a subdirectory named HAFM in your home directory). 1. In the Terminal window, type cd HAFM. 2.
Configuring Remote Workstations: HP-UX, AIX, and Linux This appendix describes the procedures for installing the high availability fabric manager on a remote HP-UX, AIX, or Linux workstation. To run the High Availability Fabric Manager on a remote workstation, you must first download and install the High Availability Fabric Manager application from the HAFM server.
Configuring Remote Workstations: HP-UX, AIX, and Linux • Ethernet network adapter. • Java-enabled Internet browser, such as Microsoft Internet Explorer (version 3.0 or later) or Netscape Navigator (version 3.0 or later). Newer versions of the High Availability Fabric Manager or Product Managers installed on the HAFM server will automatically download when the remote clients log in to the HAFM server.
Configuring Remote Workstations: HP-UX, AIX, and Linux Figure D–1: HP StorageWorks HAFM page 4. Read the instructions for your operating system. If a reference to fixes is made, click the hyperlink and verify that your system is up-to-date. 5. Click the appropriate button (Begin HP-UX Installation/Begin AIX Installation /Begin Linux Installation) to begin the installation process.
Configuring Remote Workstations: HP-UX, AIX, and Linux Figure D–2: Security Warning page 1. If you have read the security agreement information and wish to continue, click Yes. The HP High Availability Fabric Manager InstallAnywhere Web Installer page displays for HP-UX, AIX, and Linux. 2.
Page 213
Configuring Remote Workstations: HP-UX, AIX, and Linux 6. Click Next. At any time, you may return to the previous page by clicking or quit the Previous Installer by clicking Exit. The License Agreement screen displays (similar to Figure B–5 on page B-6).
Configuring Remote Workstations: HP-UX, AIX, and Linux 13. Review the installation information and click Install. The progress of the installation is tracked on the Installing High Availability Fabric Manager screen (similar to Figure B–10 on page B-10). 14. When complete, the screen shown in Figure B–11 on page B-10 displays.
Page 215
Glossary This glossary defines terms used in this guide or related to this product and is not a comprehensive glossary of computer terms. access control List of all devices that can access other devices across the network and the permissions associated with that access.
Page 216
Glossary bidirectional In Fibre Channel, the capability to simultaneously communicate at maximum speeds (100 Mbps) in both directions over a link. bit error rate Also known as BER. Ratio of received bits that contain errors to total of all bits transmitted. blocked port Devices communicating with the port are prevented from logging into the Director or communicating with other devices attached to the Director.
Page 217
Glossary Class 2 Fibre Channel service Provides a connectionless (not dedicated) service with notification of delivery or nondelivery between two N_Ports. In-order delivery of frames is not guaranteed. Class 3 Fibre Channel service Provides a connectionless (not dedicated) service without notification of delivery or nondelivery between two N_Ports.
Page 218
Glossary cyclic redundancy check Also known as CRC. System of error checking performed at both the sending and receiving station using the value of a particular character generated by a cyclic algorithm. When the values generated at each station are identical, data integrity is confirmed. DASD Direct access storage device such as a disk drive.
Page 219
Glossary E_Port See expansion port. E_D_TOV See error detect time-out value. error-detect time-out value E_D_TOV defines the time the Switch waits for an expected response before declaring an error condition. error message Indication that an error has been detected. See also error message and information message. Ethernet A widely-implemented local area network (LAN) protocol that uses a bus or star topology and served as the basis for the IEEE 802.3 standard, which specifies the physical and software...
Page 220
Glossary failover Automatic and nondisruptive transition of functions from an active FRU that has failed to a backup FRU. FCC-IOC See Fibre Channel I/O controller. A standard Fibre Channel protocol used to run SCSI over Fibre Channel. FE-MIB See Fibre Channel fabric element. fiber optics Branch of optical technology concerned with the transmission of light pulses through fibers made of transparent materials such as glass, fused silica, and plastic.
Page 221
Glossary generic port Also known as G_Port. Physical interface on a Director that can function either as a fabric port (F_Port) or an extension port (E_Port) depending on the port type to which it connects. G_Port See generic port. G_Port module (GPM) card Also known as GPM card.
Page 222
Glossary In Fibre Channel, a device that connects nodes into a logical loop by using a physical star topology. initial machine load. information message Message telling a user that a function is performing normally or has completed normally. See also error message warning message.
Page 223
Glossary latency When used in reference to a Fibre Channel switching device, latency refers to the amount of time elapsed between receipt of a data transmission at a Switch’s incoming F_Port (from the originating node port) to retransmission of that data at the Switch’s outgoing F_Port (to the destination N_Port).
Page 224
Glossary management information base Related set of software objects (variables) containing information about a managed device and accessed via SNMP from a network management station. management session Management session exists when a user logs on to the High Availability Fabric Manager. HAFM can support multiple concurrent management sessions.
Page 225
Glossary node In Fibre Channel terminology, mode refers to an end device (Server or storage device) that is or can be connected to a switched fabric. node port Physical interface within an end device which can connect to an F_Port on a switched fabric or directly to another N_Port (in point-to-point communications).
Page 226
Glossary persistent binding A form of server-level access control that uses configuration information to bind a server to a specific Fibre Channel storage volume (or logical device) using a unit number. port Receptacle on a device to which a cable leading to another device can be attached. port card Field-replaceable hardware component that provides the port connections for fiber cables and performs specific device-dependent logic functions.
Page 227
Glossary remote access link Connection to a device or program on a computer network via a (geographically) remote workstation. remote notification A process by which a system is able to inform remote users and/or workstations of certain classes of events that occur on the system. E-mail notification and the configuration of SNMP trap recipients are two examples of remote notification programs that can be implemented on director-class switches.
Page 228
Glossary storage area network A high-performance data communications environment that interconnects computing and storage resources so that the resources can be effectively shared and consolidated. subnet mask Used by a computer to determine whether another computer with which it needs to communicate is located on a local or remote network.
Page 229
Glossary unblocked port Devices communicating with an unblocked port can log in to the Director and communicate with devices attached to any other unblocked port, assuming that this is supported by the current zoning configuration. unicast Communication between a single sender and a single receiver over a network. Compare to multicast (communication between a single sender and multiple receivers) and anycast (communication between any sender and the nearest of a group of receivers).
Page 231
Index center in topology option 5–8 view menu 3–7 access, unrestricted 3–18 changing accessing, remote HAFM servers 1–6 network address 4–5 activate zone set dialog box 6–27 remote workstation address 3–18 activate zone set option, configure menu 3–20 circle symbol 2–11 activating zone sets 6–26 clear ISL alert option, view menu 3–7 active zone set...
Page 232
Index users 3–10 zone sets 6–17 E_Ports, segmented 6–9 zoning 6–11 EBCDIC code pages 8–3 major tasks 3–21 e-mail notification controlling access 6–4 enabling 3–23 controlling access, server-level 6–4 testing 3–24 corporate intranet 1–7 enable fly over display option, view menu 3–8 enable management server (FICON) 8–1 enabling default zone...
Page 233
Index fabrics controlling access 6–1 HAFM server persisting 5–5 description 1–3 renaming 5–5 name 1–4 unpersisting 5–17 remote access, managing 1–7 fabrics menu 3–3 help menu 3–26 fabrics status box 2–12 hide route option, fabrics menu 3–4 fabrics tab 2–10 5–1 High Availability Fabric Manager fabrics view 5–1...
Page 234
Index mode enterprise fabric 8–12 languages, code page 8–3 modify network address dialog box 4–5 layout icons button 2–7 modify option, product menu 3–2 layout icons option, view menu 3–7 modify user dialog box 3–13 localhost, HAFM server name 1–4 modifying logging in 1–3 to 1–3...
Page 235
Index description 4–2 illustrated 4–2 open option, product menu 3–1 maximum displayed 2–9 open product button 2–3 pop-up menu 4–5 open systems management server 8–4 Product Manager configuring 8–5 backup 1–9 installing 8–5 closing 4–9 5–8 opening main window 4–8 5–7 modify network address dialog box 4–5 opening 4–7...
Page 236
Index rights, user 3–8 routes red diamond symbol 2–11 displaying 5–22 remote access showing 5–9 blocking 3–18 managing 1–7 remote HAFM servers, accessing 1–6 SANtegrity feature 8–6 remote management sessions, specifying number fabric binding 8–6 of 3–18 SANtegrity features remote notification, testing 3–24 switch binding 8–7 remote sessions, displaying 1–8 saving, log files 7–7...
Page 237
Index switch binding 8–7 8–12 user sessions option, view menu 3–6 enable and disable 8–8 user sessions, displaying 1–8 membership list 8–9 users online state functions 8–10 adding 3–11 zoning function 8–11 deleting 3–14 switch binding membership list dialog box 8–9 maximum 3–8 switch clock alert mode 8–2 modifying 3–12...
Page 238
Index replacing 6–26 deleting 6–21 showing 5–10 6–31 description 6–6 types 6–6 displaying 6–14 WWNs 6–6 finding 6–24 zone properties dialog box 6–23 identifying by port number 6–7 zone properties, displaying 6–22 identifying by WWN 6–6 zone set library 6–8 maximum 6–17 zone set properties dialog box 6–24 members...