HP 316095-B21 - StorageWorks Edge Switch 2/24 Installation Instructions Manual

Fw 05.01.00 and sw 07.01.00 edge switch 2/24 rack mount kit installation instructions.
Hide thumbs
installation
instructions
hp StorageWorks
edge switch 2/24 rack mount kit
Product Version: FW V05.01.00-24/HAFM SW V07.01.00-09
Third Edition (June 2003)
Part Number: AA-RTDGC-TE/958-000285-002
These installation instructions provide the procedures used for installing an HP StorageWorks
Edge Switch 2/24 in an appropriate rack.

Advertising

   Related Manuals for HP 316095-B21 - StorageWorks Edge Switch 2/24

   Summary of Contents for HP 316095-B21 - StorageWorks Edge Switch 2/24

  • Page 1

    installation instructions hp StorageWorks edge switch 2/24 rack mount kit Product Version: FW V05.01.00-24/HAFM SW V07.01.00-09 Third Edition (June 2003) Part Number: AA-RTDGC-TE/958-000285-002 These installation instructions provide the procedures used for installing an HP StorageWorks Edge Switch 2/24 in an appropriate rack.

  • Page 2

    © Copyright 2002-2003 Hewlett-Packard Development Company, L.P. Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.

  • Page 3: Table Of Contents

    contents Contents About this Guide........... .5 Overview.

  • Page 4

    Contents Tables Document Conventions ........... 7 Edge Switch 2/24 Rack Mount Kit Installation Instructions...

  • Page 5: About This Guide

    about this guide About this Guide These installation instructions provide information to help you rack mount the HP StorageWorks Edge Switch 2/24 in a standard HP rack. About this Guide “About this Guide” topics include: Overview, page 6 Conventions, page 7 Rack Stability, page 10 Getting...

  • Page 6: Overview, Intended Audience, Related Documentation

    Intended Audience This book is intended for use by administrators or technicians who are experienced with the following: StorageWorks FibreChannel technology from Hewlett-Packard. Rack-mounting hardware in standard HP racks. Related Documentation For a list of corresponding documentation included with this product, see the Related Documents section of the HP StorageWorks Edge Switch Release Notes.

  • Page 7: Conventions, Document Conventions, Text Symbols

    About this Guide Conventions Conventions consist of the following: Document Conventions Text Symbols Equipment Symbols Document Conventions The document conventions included in Table 1 apply in most cases. Table 1: Document Conventions Element Convention Cross-reference links Blue text: Figure 1 Key and field names, menu items, Bold buttons, and dialog box titles...

  • Page 8: Equipment Symbols

    About this Guide Caution: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or data. Note: Text set off in this manner presents commentary, sidelights, or interesting points of information. Equipment Symbols The following equipment symbols may be found on hardware for which this guide pertains.

  • Page 9

    About this Guide Power supplies or systems marked with these symbols indicate the presence of multiple sources of power. WARNING: To reduce the risk of personal injury from electrical shock, remove all power cords to completely disconnect power from the power supplies and systems. Any product or assembly marked with these symbols indicates that the component exceeds the recommended weight for one individual to handle safely.

  • Page 10: Rack Stability

    About this Guide Rack Stability Rack stability protects personnel and equipment. To reduce the risk of personal injury or damage to the WARNING: equipment, be sure that: The leveling jacks are extended to the floor. The full weight of the rack rests on the leveling jacks. In single rack installations, the stabilizing feet are attached to the rack.

  • Page 11: Getting Help, Hp Technical Support, Hp Storage Website, Hp Authorized Reseller

    About this Guide Getting Help If you still have a question after reading this guide, contact an HP authorized service provider or access our website: http://www.hp.com. HP Technical Support Telephone numbers for worldwide technical support are listed on the following HP website: http://www.hp.com/support/.

  • Page 12

    About this Guide Edge Switch 2/24 Rack Mount Kit Installation Instructions...

  • Page 13: Rack Mount Checklist

    Rack Mount Checklist This chapter describes the contents of the rack mount kit as well as tools or equipment required to complete the installation. Note: The hardware kit includes parts not required for the configuration described in these instructions. Edge Switch 2/24 Rack Mount Kit Installation Instructions...

  • Page 14: Mounting Hardware

    Rack Mount Checklist Mounting Hardware Two (2) two-hole bar nuts Six (6) three-hole bar nuts (only 4 used) Eight (8) square alignment washers (required only for HP 9000, 10000 and 11000 series racks) Eight (8) Phillips panhead screws (10-32 x 1/2) with split lock and flat washers Four (4) Phillips flathead screws (8-32 x 7/16) Ten (10) Phillips panhead screws (10-32 x 5/8) with flat washer (only 2 used)

  • Page 15: Brackets And Rails, Brackets Included In Kit

    Rack Mount Checklist Brackets and Rails Brackets and rails included in the kit are shown in Figure 1: 1 Two (2 ) fixed-length slide rails (one left and one right) 2 Two (2) Front brackets 3 Two (2) Rear brackets (long) 4 Two (2) Rear spacing bracket 5 Rear bracket (short) - not used in this configuration Figure 1: Brackets included in kit...

  • Page 16: Required Tools

    Rack Mount Checklist Required Tools The following tools are required, but are not included in the kit: Torque driver with a T10 Torx bit #2 Phillips screwdriver Edge Switch 2/24 Rack Mount Kit Installation Instructions...

  • Page 17: Rack Mount Instructions

    Rack Mount Instructions Read these instructions to rack mount the HP StorageWorks Edge Switch 2/24 in the appropriate HP, or comparable, 19-inch Electronic Industries Association (EIA) rack: HP 9000 series, 10000 series and 11000 series racks HP rack system/e or 19-inch EIA rack Edge Switch 2/24 Rack Mount Kit Installation Instructions...

  • Page 18: Mounting The Adjustable Brackets In The Rack

    Rack Mount Instructions Mounting the Adjustable Brackets in the Rack Use these steps to install the adjustable brackets on the rack. You will need a #2 Phillips screwdriver and eight 10x32 panhead screws to complete this procedure. Note: If you are installing the Edge Switch 2/24 in an HP 9000, 10000 or 11000 series rack, you will need eight square alignment washers to complete this procedure.

  • Page 19: Mounting The Slide Rails On The Sides Of The Switch

    Rack Mount Instructions Mounting the Slide Rails on the Sides of the Switch Use these steps to install the slide rails on the sides of the switch as shown in Figure 2. You will need a torque driver with a T10 Torx bit (not supplied in the kit) and left and right slide rails to complete this procedure.

  • Page 20: Attaching The Slide Rail To The Switch

    Rack Mount Instructions Figure 2: Attaching the slide rail to the switch Edge Switch 2/24 Rack Mount Kit Installation Instructions...

  • Page 21: Installing The Switch In The Cabinet

    Rack Mount Instructions Installing the Switch in the Cabinet Use these steps to install the switch in the cabinet. You will need a #2 Phillips screwdriver and two rear spacing brackets to complete this procedure. 1. From the front side of the cabinet, slide the switch into the mounting brackets and along the rails until the rear of the switch is flush with the rear of the cabinet.

  • Page 22

    Rack Mount Instructions Edge Switch 2/24 Rack Mount Kit Installation Instructions...

  • Page 23: Index

    index authorized reseller audience storage website authorized reseller, HP technical support brackets and rails mounting hardware brackets, mounting prerequisites conventions document equipment symbols rack stability, warning text symbols rack types rails and brackets rails, mounting document related documentation conventions prerequisites related documentation slide rails, mounting switch, installing in cabinet...

  • Page 24

    Index symbols on equipment websites warning HP storage rack stability Edge Switch 2/24 Rack Mount Kit Installation Instructions...

Comments to this Manuals

Symbols: 0
Latest comments: