Event Reporting And Control By Telephone And Sms; Event Notifications By Telephone; Event Notifications By Sms; Remote Control By Telephone - Visonic POWERMASTER-10 User Manual

EVENT REPORTING AND CONTROL BY TELEPHONE AND SMS

5. Event Reporting and Control by Telephone and SMS

Event notifications by Telephone

Control
panel
The PowerMaster-10 can be programmed for
selective notification of event messages to private
telephone subscribers – See Chapter – 4C.10.
In case of alarm the following voice signal will be
sent to private telephones upon event reporting:
* FIRE: ON - ON - ON - pause....
** BURGLAR: ON continuously (
*** EMERGENCY: 2-tone siren; like an ambulance.
To stop the alarm notification – press the "2" key on
your telephone keyboard. The alarm sound will stop
immediately.
The called party must acknowledge the message (as
explained later on). However, if there is no response
the message will be repeated as many times as
possible within a 45-second time limit. When the 45
seconds are up, the PowerMaster-10 will disengage
the line and call the next private telephone number
on its list.
The called party must acknowledge the message by
pressing the "2" key on the telephone keypad. As a
result, the PowerMaster-10 may continue to notify
the next programmed telephone number, or if so
programmed, consider the event as reported - See
Chapter – 4C.10.

Event notifications by SMS

The PowerMaster-10 system when equipped with a
GSM unit can be programmed to send SMS event
notification messages to 4 pre-selected telephone
numbers - See Chapter – 4C.10. The messages can
be tagged with a "House ID" name, for example,
"JOHN'S HOME", see Remote Control by SMS
section, command no. 9.
Example of the reported SMS messages:
•
JOHN'S HOME
**AWAY**
•
JOHN'S HOME
**DISARM**
•
JOHN'S HOUSE
POWERMASTER-10: LOW BATTERY
GARAGE: LOW BATTERY
•
JOHN'S HOUSE
STATUS MESSAGE 01
(Event list is displayed)
Note: Status messages can be sent only to a calling
telephone whose identity number is not blocked by
the user!
D-302757
(- - - - - -
......).
...)

Remote Control by Telephone

The PowerMaster-10 allows you to initiate calls from
your private telephone to the PowerMaster-10 control
panel via PSTN (landline) or GSM and to perform a
variety of arming commands remotely using your
telephone's keypad.
To connect to the PowerMaster-10 via PSTN:
1. Dial the PowerMaster-10 PSTN tel. No.
2. Wait for 2-4 rings then hang up.
3. Wait 12-30 sec.
4. Redial PowerMaster-10 tel. No. (Sound will be
heard for 10 sec.).
5. [*] (to stop the sound)
6. [User code], [#]
7. [Desired command, see next table]
To connect to the PowerMaster-10 via GSM:
1. Dial the PowerMaster-10 GSM tel. No.
2. Wait for 2-4 rings then hang up.
3. Wait 12-30 sec.
4. Redial PowerMaster-10 GSM tel. No.
5. [User code], [#]
6. [Desired command, see next table]
Notes:
(1) Alternative to steps 2 – 4: The PowerMaster-10
responds in a similar way if you just dial once
and wait until you hear telephone rings (in USA,
for example, 11 rings).
(2) Entering of user code is required once only.
(3) If you wait more that 50 seconds (may change
according to setup / use) without keying a command,
the PowerMaster-10 will disconnect the line.
The following table lists the commands and their
respective key sequence.
Command
Disarming
Arming Home
Arming Home-Instant
Arming Away
Arming Away-Instant
Arming Away-Latchkey
Arming Away-Instant-
Latchkey
Quit (end
communication)
1
2
3
1
2
3
Keying Sequence
[ ] [1] [#]
[ ] [2] [#]
[ ] [21] [#]
[ ] [3] [#]
[ ] [31] [#]
[ ] [4] [#]
[ ] [41] [#]
[ ] [99] [#]
33