Special Functions; Looking After People Left At Home; Emergency Calls For Help; Remote Control By Telephone - Visonic PowerMaxComplete User Manual

Fully supervised wireless alarm control system
Hide thumbs Also See for PowerMaxComplete:
Table of Contents

Advertisement

6. Special Functions

Looking after People Left at Home

An
important
characteristic
PowerMaxComplete
is its ability to function in a
mode contrary to the usual behavior of an alarm
system. When the system is in the disarmed state (or
even when armed "HOME" with perimeter protection
only), it can keep track of in-house activity and will
report lack of motion in interior zones if there is no
detection of motion within predetermined time limits.
To use this characteristic, you must ask your installer
to program a specific time limit beyond which lack of
motion will be reported as a "not active" alert.
To make things clear, let us assume that an elderly,
sick or handicapped person is left unattended in a
protected site. This person, disabled or sick as he
may be, will not stay entirely still for hours. It is only
natural that even while being asleep he will turn over
in his bed from time to time. He might also wander
into the kitchen to eat or drink, or to the bathroom for
other necessities. Upon doing so, the bedroom,
bathroom and kitchen motion detectors will detect his
movement.
If, for example, the "lack of motion" time limit is set by
your installer to 6 hours, a virtual 6-hour clock will
carry out a 6-hour "countdown".
If motion is detected within the 6-hour time frame, the
countdown will restart from the beginning (the virtual
6-hour clock will be "reset") and no alert message will
be sent out.
If no motion is detected within the 6-hour time frame
in any interior zone, the control panel will send a
"not-active" alert message to the central monitoring
station or to private telephones designated by the
installer.
IMPORTANT! In addition, you may provide the
person confined to interiors with a single-button
transmitter
for
distress
paragraph.

Emergency Calls for Help

Suppose the disabled person discussed above has
an accident such as falling in the bathtub without
being able to get up. It might take hours before the
"No Active" alert is sent out, but he (or she) must be
assisted much sooner.
Even though the odds for such an accident are not
high, it is advisable to provide the disabled person
with a miniature, single-button pendant-type or
wristwatch-type transmitter. Pressing the button on
this transmitter will cause the PowerMaxComplete to
send an "emergency call" to the central monitoring
station or to private telephones designated by the
installer.
D-300886
To make this possible, ask your installer to define
one of the 28 zones of the PowerMaxComplete as
of
the
an emergency zone.
Then, obtain one of the transmitters listed below and
link this transmitter's ID code to the emergency zone.
Compatible distress transmitters are (see Fig. 5):
MCT-201 - pendant-type
MCT-211 - wristwatch-type
MCT-101 - pocket-type

Remote Control by Telephone

A. Establishing Telephone Communication
You can access the PowerMaxComplete
from a remote telephone and perform arming and
disarming, activation and deactivation of electrical
devices and the auxiliary output (PGM), record,
playback
investigate the system status. The process is shown
in the next illustration.
1. Dial the PowerMaxComplete tel. No.
2. Wait for 2-4 rings then hang
3. Wait 12-30 sec.
4. Redial
situations,
see
next
5.
6.
7.
Notes
(1) The PowerMaxComplete responds in a similar
(2) Entering of user code is required once only.
(3) If you wait more that 50 seconds (may change
SPECIAL FUNCTIONS
MCT-201
MCT-211
Figure 5. Single-button Emergency Transmitters
and
erase
a
voice
up.
PowerMaxComplete
tel.
No. (Sound will be heard
for 10 sec.).
[*} (to stop the sound)
2
[user code], [#]
[Desired command, see next table]
way if you just dial once and wait until you hear
telephone rings (in USA, for example, 11 rings).
according to setup / use) without keying a
command, the PowerMaxComplete will disconnect
the line.
MCT-101
control
panel
system
message,
and
Not applicable
when dialing to the
GSM number of
the
PowerMaxComple
te. Proceed to
step 5.
1
3
17

Advertisement

Table of Contents
loading

Table of Contents