Table of Contents
Advertisement
L2DR-BL Single Pedestal Desk
NOTE: Open and assemble only one product
at a time to avoid a potential mix-up of parts
and hardware.
It is adviseable to assemble the unit on a
carpet to avoid scratches.
Assembly
STEP 1:Unpack and inspect individual pieces for damages or missing hardware.
STEP 2: Pick a clean unobstructed area to assemble desk. It is advisable to assembly
of this product upright.
STEP 3: Handles for Pedestals are Shipped Installed on the inside of the cabinet.
Remove handle from the inside of the cabinet and re-install with the same screws on
the front of cabinet.
a. Levellers for pedestals are shipped inside the unit. These levellers should
be installed prior assembling complete unit.
6" REC MOD
92.2mm
96mm
102.7mm
Installation For Similar Products
L2DRHxxxxBL
L2DBHxxxxBR
globalfurnituregroup.com
Required Tools
Safety Glasses
Included Hardware
Blum Connector
Screw L005650060
"T" Nut Insert
L007250039
FLUSH MOD
HALF HEIGHT
MODESTY
FULL HEIGHT
MODESTY
Back Panel
9.5mm
Top Underside
162mm
L2DBxxxxBL
LICENCE INSTALLATION
Screwdriver #2 Phillips
Rubber Mallet
Blum Connector
Modular Connector
(installed) L005650061
(installed) L004250001
Wood Screw #8 3/4
L007250032
STEP 4: IArrange Pedestal and gable as per the final configuration of the product.
a. Using a 1/8" drill bit, drill though holes into side of pedestal according to
the provided template on the side of the pedestal exposed to the underside
of the desk. For this application, use the full modesty and recessed panel
location.
b. Modular screws are to be installed into these holes
STEP 5: Gable has Blum connectors pre-installed. Orient gable with Blum Connectors
facing inside of desk.
Install levelers into T nut inserts on the bottom of the Gable.
a. Install Blum Connector screws into pre-drilled holes on top edge of the gable
STEP 6: The modesty panel comes with Modular connectors installed on to connect
to the Pedestal.
On the top edge of the modesty panel, install Blum Connector screws into the pre-
drilled holes.
On side of Modesty panel lining up with the gable, install Blum Connector screws into
pre-drilled holes.
• There are 2 holes here, select hole closest to underside of assembly to
correctly line up with the Blum Connectors.
a. Attach the modesty panel to the pedestals by lining up modular con
nectors to screws installed on the pedestal, lift modesty and slide into
position ensuring to engage connectors to screws. You can use a mallet to
securely seat the modesty panel into position.
b. Connect the gable to the modesty panel by lining up Blum Connector
screws to the Blum connectors. Turn the screw on Blum Connector ¼ turn,
do not over tighten.
STEP 7: To install the worksurface top. The worksurface comes with Blum Connec-
tors pre-installed on the bottom of the surface. Lift worksurface over the assembly
and line up Blum connectors to the installed Blum connector screws on the modesty
panel and gable. Turn screw on Blum Connector ¼ turn, do not over tighten.
a. You must also secure the worksurface top to the pedestal. Line up the
top flush to the side and front of the pedestal. Use #8 x 3/4 wood screws
provided, screw through the mounting bar on the pedestal to secure the
top. Note: Drawers need to be removed to access drilling location.
STEP 8: When final position has been located, level the unit with the levellers installed
on Gable and pedestal
Level
Modular Screw
Leveler
L007250001
L007240005
CANADA
10
Advertisement
Table of Contents
