Table of Contents
Advertisement
L2DRHxxxxBR • Single Pedestal Desk Resessed Half Modesty
NOTE: Open and assemble only one product
at a time to avoid a potential mix-up of parts
and hardware.
It is adviseable to assemble the unit on a
carpet to avoid scratches.
Assembly
STEP 1: Unpack and inspect individual pieces for damages or missing hardware
STEP 2: Pick a clean unobstructed area to assemble desk. It is advisable to assembly
of this product upside down.
STEP 3: Handles for Pedestals are Shipped Installed on the inside of the cabinet.
Remove handle from the inside of the cabinet and re-install with the same screws on
the front of cabinet.
a. Levellers for pedestals are shipped inside the unit. These levellers should
be installed prior assembling complete unit.
6" REC MOD
92.2mm
96mm
102.7mm
Installation For Similar Products
L2DRHxxxxBL
L2DBHxxxxBR
globalfurnituregroup.com
Required Tools
Safety Glasses
Included Hardware
Blum Connector
Screw L005650060
"T" Nut Insert
Wood Screw #8 3/4
L007250039
L007250032
FLUSH MOD
HALF HEIGHT
MODESTY
FULL HEIGHT
MODESTY
9.5mm
162mm
L2DBxxxxBL
LICENCE INSTALLATION
Screwdriver #2 Phillips
Screwdriver Roberson
Blum Connector
Modular Connector
(installed) L005650061
(installed) L004250001
STEP 4: Arrange Pedestal and gable as per the final configuration of the product.
a. Using a 1/8" drill bit, drill though holes into side of pedestal according to
the provided template on the side of the pedestal exposed to the underside
of the desk. For this application, use the full modesty and recessed panel location.
b. Modular screws are to be installed into these holes
STEP 5: Gable has Blum connectors pre-installed. Orient gable with Blum Connec-
tors facing inside of desk.
Install levellers into T nuts, using mallet install into pre-drilled holes on the bottom
of gable.
a. Install Blum Connector screws into pre-drilled holes on top edge of the gable.
STEP 6: The modesty panel comes with Modular connectors installed on to connect
to the Pedestal. On the top edge of the modesty panel, install Blum Connector
screws into the pre-drilled holes. On side of Modesty panel lining up with the gable,
install Blum Connector screws into pre-drilled holes.
• There are 2 holes here, select hole closest to underside of assembly to
correctly line up with the Blum Connectors.
a. Attach the modesty panel to the pedestals by lining up modular con
nectors to screws installed on the pedestal, lift modesty and slide into po
sition ensuring to engage connectors to screws. You can use a mallet to
securely seat the modesty panel into position.
b. Connect the gable to the modesty panel by lining up Blum Connector
screws to the Blum connectors. Turn the screw on Blum Connector ¼
turn, do not over tighten
STEP 7: To install the worksurface top. The worksurface comes with Blum Connec-
tors pre-installed on the bottom of the surface. Lift worksurface over the assembly
and line up Blum connectors to the installed Blum connector screws on the mod-
esty panel and gable. Turn screw on Blum Connector ¼ turn, do not over tighten.
a. You must also secure the worksurface top to the pedestal. Line up the
top flush to the side and front of the pedestal. Use #8 x 3/4 wood screws
provided, screw through the mounting bar on the pedestal to secure the
top. Note: Drawers need to be removed to access drilling location
STEP 8: When final position has been located, level the unit with the levellers
installed on Gable and pedestal.
Rubber Mallet
Modular Screw
Leveler
L007250001
L007240005
CANADA
12
Advertisement
Table of Contents
