Bronpi Trebol Installation, Operating And Servicing Instruction page 39

10.4.5. AUTOMATIC POWER
This is accessed by simultaneously pressing the P3 and P4 keys for 3 seconds.
Subsequently, press the P2 button until the word "AUPO" appears on display D1, then
confirm the submenu with the P3 button. Press the P3 key again to enter modification.
The selected value (OFF/ON) flashes. Modify the value with keys P2 and P4, and
press P3 again to store the set value (see drawing D10.20). If you choose the ON
option, you can set the combustion power in automatic mode only, whereas with the
value set to OFF, you can choose the 5 power levels of the stove.
10.4.6. MANUAL PELLET LOADING
In the event that the stove runs out of fuel during operation, in order to avoid an
anomaly at the next ignition, it is possible with the stove switched off and cold, as well
as with the door closed, to preload pellets for a maximum time of 300 seconds, in
order to load the auger.
This is done by simultaneously pressing the P3 and P4 keys for 3 seconds. Then
press the P2 button until the word "LOAD" appears on the D1 display, then confirm
the submenu by pressing the P3 button. Press the P3 key again to start a 300-second
counter. To interrupt charging, simply press any key.
Before restarting the stove, remember to empty the pellet burner completely to avoid
a dangerous situation. (See drawing D10.21).
P1
30
soft
P3
temperature, as it will work at minimum power.
10.4.8. TECHNICAL MENU
This menu is password-protected and is reserved for technical personnel with
specific product experience. Changing the parameters of the stove may cause the
loss of the warranty as well as serious damage to the equipment, people and the
environment. For this reason, Bronpi Calefacción s.l. assumes no responsibility if the
parameters have been modified by unauthorised personnel (see drawing D10.23).
P1
13:00
23
P3
The maximum duration of the ignition phase is 20 minutes. If after this time there is not flame, the stove will automatically activate the alarm
state and the display will show the alarm message "Er12".
P1
CHEC
3 22
P3 P4
D10.25
INSTALLATION, OPERATING AND SERVICING INSTRUCTIONS
10.4.7.
P2
This is accessed by simultaneously pressing the P3 and P4 keys for 3 seconds. Then
press the P2 button until the word "SOFT" appears on display D1, then confirm the
submenu by pressing the P3 button. Press the P3 key again to enter modification. The
selected value (OFF/ON) flashes. Modify the value with keys P2 and P4, and press P3
again to store the set value (see drawing D10.22). If you choose the ON option, the
stove is set to working power 1 (minimum power), and the main fan stop working.
P4
On the other hand, if AUTO option is selected, the channelling will be switched
off, but if 1,2,3,4 or 5 is selected, the channelling will run at the desired speed.
D10.22
In this working mode, it is very likely that the stove won't reach the selected room
10.5.
P2
The normal operation of the display/receiver is described below.
Before switching on the display, the stove state is showed in drawing D10.24. It only
shows the room temperature and the current time.
10.5.1.
In order to ignite the stove, simply press the key P1 during a few seconds. Firstly, the
P4
stove carries out an initial check-up and continues the ignition process. After this,
the display shows different steps of the ignition process (2, 3 and 5) (see drawings
D10.24
D10.25, D10.26, D10.27 and D10.28).
P2 P1
ON 2
3 22
P3
SOFT MODE
USER MODE
IGNITION OF THE STOVE
P2 P1
ON 4
3 22
P4 P3
D10.26
38
P1
on
aupo
P3
P1
30
load
P3
P1
----
TPAR
P3
P2 P1
ON 5
3 22
P4 P3
D10.27
TREBOL - MILA - MINERVA
P2
P4
D10.20
P2
P4
D10.21
P2
P4
D10.23
P2
P4
D10.28