Bronpi Trebol Installation, Operating And Servicing Instruction page 37

10.4.2. DUCTED FAN POWER REGULATION
This is accessed by simultaneously pressing keys P3 and P4 for 3 seconds. Then
press the P2 button until the word "Can" appears on display D1, then confirm the
submenu by pressing the P3 button. Press the P3 key again to enter modification.
The selected value (OFF, 1, 2, 3, 4, 5 or auto) flashes. Change the value with the P2
and P4 keys. Press the P3 key to go on to modify the other parameters and press P3
again to store the set value (see drawing D10.9). If you choose speeds 1 to 5, the
ducted fan speed will always be the one you have chosen (1 minimum speed and
5 maximum speed), in other words, it will blow the same flow of hot air through the
duct regardless of the working power of the stove, whereas in the auto selection, the
ducted fan speed will be automatically regulated according to the working power of
the stove. If you wish to deactivate the channelling fan operation, you must select the
OFF option.
NOTE. If you activate Soft mode, this regulation is available. If AUTO option is selected, the channelling will be switched off, but if 1,2,3,4 or 5
is selected, the channelling will run at the desired speed.
10.4.3. SET UP DATE AND TIME
It is necessary to press simultaneously during 3 seconds keys P3 and P4. Later,
press key P2 until the display D1 shows the word "oroL" and confirm the submenu
with key P3. Press again key P3 to modify. The value selected (hours, minutes, day,
etc) flashes. Modify the value with keys P2 and P4. Press key P3 in order to modify
the rest of parameters and press again P3 to save the value set (see drawing
D10.10).
10.4.4. PROGRAMMING THE STOVE
P1
cron
P3
Gior: Daily Programming
Sett: Weekly Programming
FiSE: Weekend programming
OFF: Disable all programmings
- Menu Programming Time Bands
The word "ProG" appears in the display. It consists of 3 submenus corresponding to the 3 programming modes allowed:
- Daily: Allows you to configure 3 schedules for each day of the week.
- Weekly: Allows you to configure 3 schedules per day, same for each day of the week.
- Weekend: It allows you to configure 3 schedules per day, differentiating between the programming from Monday to Friday and the one
of Saturdays and Sundays.
Daily mode: the day of the week
Weekly mode: Monday-Sunday
Weekend mode: Monday-Friday
For the On time, the segment in the lower part of the display D2 is
turned on
For the Off time, the segment on the top of the display D2 is turned
on
For each programming you have to set the ON time and the OFF time. The steps to follow would be the following:
INSTALLATION, OPERATING AND SERVICING INSTRUCTIONS
This menu is used to
set timing on the startup and shutdown sequences. Press the keys P3 and P4
P2
simultaneously for 3 seconds. Then press the P2 key until the word "Cron" appears
on the display D1, then confirm the submenu with the P3 key (see drawing D10.11).
It consists of two submenus:
-
The word "ModE" appears on the display. This menu allows you to select the
P4
operation mode of the thermostat and activate it. You can only choose one
programming mode. You must confirm the mode chose with the P3 key.
D10.11
MODE
VIEWINGS
Saturday-Sunday
P1
P1
Menu Chrono Enabled
36
off
can
P3 P4
13:00
fr
P3 P4
LED
DISPLAY
M o
M S
M F
S S
- - - -
1 M o
I
- - - -
1 M o
I
TREBOL - MILA - MINERVA
P2
D10.9
P2
D10.10