Bronpi Trebol Installation, Operating And Servicing Instruction page 26

1 GENERAL WARNINGS
The installation of the stove must be done according to the local, national or European regulations.
Stoves by Bronpi Calefacción, S.L. are manufactured under a quality control system in order to protect both the user and the fitter in the
event of possible accidents. We also recommend to the authorized installer that, each time an operation in the stove is going to be done,
pay special attention to the electrical connections, especially that stripped or bear wires are never left outside the connections, avoiding
dangerous contacts.
Connect the stove to a power socket homologated of 230 V- 50 Hz – IP20.
The installation must be performed by authorized personnel who must provide the buyer a declaration of conformity of the
installation where he will assume full responsibility for the final installation and, therefore, the proper operation of the installed
product. Bronpi Calefacción S.L. will not assume any liability in the case of failure complying with these precautions.
The manufacturer will not assume any liability for damages caused to third parties due to improper installation or misuse of the stove.
In order to ensure the correct operation of the product, components can only be replaced with original spare parts and by an authorized
technician.
Maintenance of the stove must be performed at least once a year by an Authorized Technical Service.
For more security you should consider:
• Do not touch the stove with bare feet or with wet body parts.
• The door(s) of the equipment must be closed during operation.
• It is forbidden to modify the safety or regulating devices without the permission of the manufacturer.
• Avoid direct contact with any parts of the product that tend to reach high temperatures during its operation.
This stove can be used by children aged from 8 years and by persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge whenever they have supervision or they have received instruction concerning the use of the stove in a safe way
and understand the hazards involved. Children must not play with the stove. Cleaning and user maintenance shall not be made by children
without supervision.
2 GENERAL DESCRIPTION
The stove that you have purchased contains the following pieces:
• Complete structure of the stove on the pallet.
• Inside the combustion chamber you can find a box/bag with a thermal glove that allows us to manipulate the door handle and other
components (burner). The electrical interconnection cable between the stove and the electrical network. A hook (cold hands handle) to
make easier the removing and cleaning of the burner. In the models. A book in order to register all maintenance tasks performed to the
stove as well as this installation, use and servicing manual.
• Inside the combustión chamber, you will find the baffle plate, the burner and the ash pan.
The equipment consists of several elements of steel sheets welded. It also has a door with vitro ceramic glass (resistant up to 750ºC) and
ceramic cord for the air tightness in the combustion chamber.
Heating is produced by:
a. Forced convection: thanks to the fan placed on the bottom of the stove, the air at room temperature is aspired and it is returned to the
room at a higher temperature.
b. Radiation: through the vitro ceramic glass and the body the heat is irradiated towards the environment.
3 FUELS
WARNING!!!
The use of a low quality pellet or any other fuel in disagreement with the specifications mentioned below implies the
cancellation of the warranty and the responsibility bounded to the product
Only wood pellets certified by these standards or certifications should be used :
Standards:
• Ö-Norm M 7135 | Din 51731 | EN-14962-2 (all repealed and included in ISO-17225-2)
• ISO-17225-2
Quality certifications:
• DIN+
• ENplus: On the web site (www.pelletenplus.es) you can check all manufacturers and distributors with certificate.
It is strongly recommended that the pellet is certified with quality certifications because this is the only way to guarantee the
constant quality of the pellet.
Bronpi Calefacción recommends the use of pellets with 6 mm diameter, a maximum longer of 3.5 cm and with a humidity percentage lower
than 8%.
• STORAGE OF PELLET
In order to guarantee combustion without any problem it is necessary to keep the pellet in a dry ambient.
• PELLET SUPPLY
Open the tank cover on the top of the equipment and empty directly the pellet bag taking care of not overflowing.
INSTALLATION, OPERATING AND SERVICING INSTRUCTIONS 25 TREBOL - MILA - MINERVA