Timing Characteristics - Texas Instruments MSPM0G350 Series Manual

www.ti.com
(4) Program time is defined as the time from when the program command is triggered until the command completion interrupt flag is set in
the flash controller.
(5) Sector program time is defined as the time from when the first word program command is triggered until the final word program
command completes and the interrupt flag is set in the flash controller. This time includes the time needed for software to load each
flash word (after the first flash word) into the flash controller during programming of the sector.
(6) Flash word size is 64 data bits (8 bytes). On devices with ECC, the total flash word size is 72 bits (64 data bits plus 8 ECC bits).

7.8 Timing Characteristics

VDD=3.3V, T =25℃ (unless otherwise noted)
a
PARAMETER
Wakeup Timing
t
WAKE,
Wakeup time from SLEEP1 to RUN
SLEEP1
t
WAKE,
Wakeup time from SLEEP2 to RUN
SLEEP2
t Wakeup time from STANDBY0 to RUN
WAKE,
(1)
STANDBY0
t Wakeup time from STANDBY1 to RUN
WAKE,
(1)
STANDBY1
t Wakeup time from STOP0 to RUN
WAKE,
(SYSOSC enabled)
STOP0
t Wakeup time from STOP1 to RUN
WAKE,
(SYSOSC enabled)
STOP1
t Wakeup time from STOP2 to RUN
WAKE,
(SYSOSC disabled)
STOP2
t Wakeup time from SHUTDOWN to
WAKEUP,
(2)
RUN
SHDN
Asynchronous Fast Clock Request Timing
t Delay time from edge of asynchronous
DELAY,
request to first 32MHz MCLK edge
SLEEP1
t Delay time from edge of asynchronous
DELAY,
request to first 32MHz MCLK edge
SLEEP2
t Delay time from edge of asynchronous
DELAY,
request to first 32MHz MCLK edge
STANDBY0
t Delay time from edge of asynchronous
DELAY,
request to first 32MHz MCLK edge
STANDBY1
t Delay time from edge of asynchronous
DELAY,
request to first 32MHz MCLK edge
STOP0
t Delay time from edge of asynchronous
DELAY,
request to first 32MHz MCLK edge
STOP1
t Delay time from edge of asynchronous
DELAY,
request to first 32MHz MCLK edge
STOP2
Startup Timing
t Device cold startup time from reset/
START,
(3)
power-up
RESET
NRST Timing
t Pulse length on NRST pin to generate
RST,
BOOTRST
BOOTRST
Pulse length on NRST pin to generate
t
RST, POR
POR
(1) The wake-up time is measured from the edge of an external wake-up signal (GPIO wake-up event) to the time that the first instruction
of the user program is executed, with glitch filter disabled (FILTEREN=0x0) and fast wake enabled (FASTWAKEONLY=1) .
(2) The wake-up time is measured from the edge of an external wake-up signal (IOMUX wake-up event) to the time that first instruction of
the user program is executed.
Copyright © 2023 Texas Instruments Incorporated
TEST CONDITIONS
(1)
(1)
(1)
(1)
(1)
Fast boot enabled
Fast boot disabled
Mode is SLEEP1
Mode is SLEEP2
Mode is STANDBY0
Mode is STANDBY1
Mode is STOP0
Mode is STOP1
Mode is STOP2
Fast boot enabled
Fast boot disabled
ULPCLK≥4MHz
ULPCLK=32kHz
Product Folder Links: MSPM0G3507-Q1 MSPM0G3506-Q1 MSPM0G3505-Q1
MSPM0G3507-Q1, MSPM0G3506-Q1, MSPM0G3505-Q1
MIN TYP
15.2
15.2
12.1
13.5
12.9
240
252
0.33
0.93
260
308
Submit Document Feedback
SLASF88 – OCTOBER 2023
MAX UNIT
1.5 us
2.1 us
us
us
us
us
us
us
us
3.2 us
3.2 us
0.1 us
2.4 us
0.9 us
us
1.5
us
80
1 s
33