Table of Contents
Advertisement
Operating Instructions
Pressing 2 for POTS Settings while viewing Communicator Screen #1 will display settings for the telephone portion of the Communicator.
Pressing 1 or 2 will display whether each phone line is enabled Yes or disabled No, whether the phone type is touchtone or rotary, and
whether the phone line is being supervised Yes or No.
Pressing 3 will display the phone lines' Gains setting. The value for the Dialing Gains and Reporting Gains is shown as High, Normal, or
Low.
READ STATUS
INSTALLED
2=POTS SETTINGS
3=IP SETTINGS
Communicator Screen #1
COMMUNICATOR
1=PRI COMM PATH
2=SEC COMM PATH
TBL REPORT LIMIT
Communicator Screen #2
Pressing 1 for POTS indicates whether the receiver has been enabled or disabled. It also provides information on the receiver such as:
•
Account Code
•
Phone Number
•
Communication Format
Pressing 2 for Ethernet indicates whether the receiver has been enabled or disabled. It also provides information on the receiver such as Cen-
tral Station (CS) account info.
COMMUNICATOR
1=EVENT CODES
TEST TIME INT
24HR TEST TIME
Communicator Screen #3
COMMUNICATOR
REPORT STYLE
Communicator Screen #4
4.23.11 Print
READ STATUS
1=REVISIONS
2=PRINT
3=TIME/DATE
Read Status Screen #5
On Revisions Screen #1, press the corresponding number to view the software versions of the FACP panel, the IPOTS-COM communicator,
and the FACP display. On Revisions Screen #2, press the corresponding number to view the software information for any SLC3-LS loop
card installed on the panel.
To print program data or control panel status, press 2 while viewing Read Status Screen #5. The following screens will be displayed:
Pressing 1 while viewing Print Screen #1 allows the user to print the History file which will detail all of the system activities since the file
was last cleared from memory.
Pressing 2 while viewing Print Screen #1 allows the user to print the Walktest log which will detail all of the system activations during walk-
test since the log was last cleared.
114
Pressing 3 for IP Settings while viewing Communicator Screen #1 will display settings for the ethernet portion
of the Communicator. Pressing 1 for IP Addresses will show the subnet mask address for the communicator.
YES
The screen will also indicate if DHCP has been enabled Yes or disabled No. If the DHCP has not been enabled,
the Static Settings will be displayed.
Communicator Screen #2 allows the programmer to press 1 to view the Primary Communication Path settings
or 2 to view the Secondary (backup) Communication Path settings for the Communicator and indicates the Call
Limit for Communicator trouble calls within a 24 hour period.
0
Pressing 1 for the Primary Communication Path or 2 for Secondary Communication Path while viewing Com-
municator screen #2 will cause the following screen to be displayed:
COMMUNICATOR
1=POTS
2=ETHERNET
Communicator Screen #3 allows the user to view the Event Codes for the chosen communication format as
well as the Test Time Interval and 24 Hour Test Time.
24
0100
Communicator Screen #4 allows the user to view whether the reporting style is by Point or Zone.
POINT
Pressing 1 while viewing Read Status Screen #5 will display the following:
1=PANEL
2=COMMUNICATOR
3=DISPLAY
PRINT
1=HISTORY
2=WALKTEST LOG
3=WALKTEST SUMMARY
Print Screen #1
POTS SETTINGS
1=LINE 1
2=LINE 2
3=GAINS
REVISIONS
Revisions Screen #1
PRINT
1=DETECTOR DATA
2=COMM SETTINGS
3=EXIT PRINTING
Print Screen #2
ES-1000X Series Manual — P/N LS10133-000FL-E:A 6/21/2023
REVISIONS
1=LOOP CARD 1
2=LOOP CARD 2
3=LOOP CARD 3
Revisions Screen #2
Read Status
Advertisement
Table of Contents
