IKEA RENGORA Manual page 48

Hide thumbs Also See for RENGORA:

Manual (80 pages)

Owner's manual (48 pages)

Instruction manual (29 pages)

Table Of Contents

Table of Contents

LOAD THE RACKS (see LOADING THE RACKS)

vided that it has only just begun: open the door, press and hold

FILLING THE DETERGENT DISPENSER

the ON/OFF button, the machine will switch off.

(see PROGRAMS TABLE).

ENGLISH

Switch the machine back on using the ON/OFF button and select

CHOOSE THE PROGRAM AND CUSTOMISE THE CYCLE

the new wash cycle and any desired options; Start the wash cycle

Select the most appropriate program in accordance with the

SRPSKI

by pressing START/Pause button and closing the door within 4 sec.

type of crockery and its soiling level (see PROGRAMS

DESCRIPTION) by pressing the

Make sure the cap is screwed on tightly, so that no detergent can

ADDING EXTRA CROCKERY

Select the desired options (see OPTIONS AND FUNCTIONS).

get into the container during the wash program (this could damage

Without switching off the machine, open the door (START/Pause

START

ENGLISH

the water softener beyond repair).

led starts blinking) (be ware of HOT steam!) and place the

Start the wash cycle by pressing START/Pause button (led

As soon as this procedure is complete, run a program without

is lit) and closing the door within 4 sec. When the program

Funkcije

crockery inside the dishwasher. Press the START/Pause button

starts you hear a single beep. If the door was not closed within

loading. The "Pre-Wash" program alone is NOT

and close the door within 4 sec., the cycle will resume from the

4sec., the alarm sound will be played. In this case, open the

Residual saline solution or grains of salt can lead to corrosion,

point at which it was interrupted.

Make sure the cap is screwed on tightly, so that no detergent can

door, press START/Pause button and close the door again

irreparably damaging the stainless steel components.

NATURALDRY

within 4 sec.

get into the container during the wash program (this could damage

The guarantee is not applicable if faults are caused by such

ACCIDENTAL INTERRUPTIONS

END OF WASH CYCLE

the water softener beyond repair).

Sistem za otvaranje vrata NaturalDry je sistem konvekcionog

circumstances.

The end of the wash cycle is indicated by beeps and by the

If the door is opened during the wash cycle, or if there is a power

As soon as this procedure is complete, run a program without

sušenja koji automatski otvara vrata tokom/nakon faze sušenja i koji

ENGLISH

flashing of the wash cycle number on the display. Open the

cut, the cycle stops. Press the START/Pause button and close

loading. The "Pre-Wash" program alone is NOT

svakodnevno obezbeđuje izvanredne performanse sušenja. Vrata se

door and switch off the appliance by pressing the ON/OFF

the door within 4 sec., the cycle will resume from the point at

Residual saline solution or grains of salt can lead to corrosion,

heating element may be damaged as a result.

otvaraju na temperaturi koja je bezbedna za kuhinjski nameštaj.

button.

which it was interrupted.

irreparably damaging the stainless steel components.

Whenever you need to add salt, it is mandatory to complete

Wait for a few minutes before removing the crockery - to avoid

Posuđe ne vadite odmah nakon što se vrata otvore, već sačekajte da

The guarantee is not applicable if faults are caused by such

burns. Unload the racks, beginning with the lower one.

the procedure before the beginning of the washing cycle.

bi se pravilno osušilo.

circumstances.

Funkcija se ne može aktivirati za sve programe, pogledajte tabelu

SETTING THE WATER HARDNESS

Functions

programa.

To allow the water softener to work in a perfect way, it is essential

heating element may be damaged as a result.

Radi dodatne zaštite od pare, mašini je dodata posebno dizajnirana

DELAY

that the water hardness setting is based on the actual water hard-

1. ECO - Normally soiled crockery. Standard program, the most efficient in terms of its combined energy and water

Whenever you need to add salt, it is mandatory to complete

ENGLISH

zaštitna folija. Da biste videli kako da postavite zaštitnu foliju,

ness in your house. This information can be obtained from your local

consumption.

The start time of the program may be delayed for a period

the procedure before the beginning of the washing cycle.

water supplier. The factory setting is for average (3) water hardness.

pogledajte (UPUTSTVO ZA SKLAPANJE).

ENGLISH

2. NORMAL - Mixed soil. For normally soiled dishes with dried food residues.

of time between 1 and 12 hours.

Korisnik može onemogućiti funkciju NaturalDry na sledeći način:

SETTING THE WATER HARDNESS

3. INTENSIVE - Program recommended for heavily soiled crockery, especially suitable for pans and saucepans (not to be used

• Switch on the appliance by pressing the ON/OFF button.

ENGLISH

1. Idite na softver mašine za pranje posuđa pritiskom i zadržavanjem

1. Press the DELAY button: the corresponding «h» symbol

for delicate items).

• Switch off the appliance by pressing the ON/OFF button.

To allow the water softener to work in a perfect way, it is essential

ENGLISH

dugmeta

(6 sek).

appears on the display; each time you press the button,

4. PRE-WASH - Use to refresh crockery planned to be washed later. No detergent to be used with this program.

• Hold down button

for 5 seconds, until you hear a beep.

that the water hardness setting is based on the actual water hard-

5. FAST - Normally soiled crockery. Everyday cycle, that ensures optimal cleaning performance in shorter time.

• Switch on the appliance by pressing the ON/OFF button.

2. Prešli ste na kontrolni meni za funkciju NaturalDry, trebalo bi da

ness in your house. This information can be obtained from your local

DELAY

the time (1h, 2h, etc. up to max. 12h) from the start of

ENGLISH

•

The current selection level number and the salt indicator light

6. SANITIZING - Normally or heavily soiled crockery, with additional antibacterial wash. Can be used to perform

water supplier. The factory setting is for average (3) water hardness.

promenite status funkcije NaturalDry pritiskom na dugme

the selected wash cycle will be increased.

The start time of the program may be delayed for a period

DELAY

maintenance of the dishwasher.

E – omogućeno d – onemogućeno

of time between 1 and 12 hours.

2. Select the wash program, press the START/PAUSE

• Switch on the appliance by pressing the ON/OFF button.

ENGLISH

The start time of the program may be delayed for a period

•

Press button

7. SELF- CLEAN - Program to be used to perform maintenance of the dishwasher. It cleans the interior of the appliance

to select the desired hardness level (see

DELAY

Da biste potvrdili izmenu i izašli iz kontrolnog menija, pritisnite i

DELAY

• Switch off the appliance by pressing the ON/OFF button.

1. Press the DELAY button: the corresponding «h» symbol

button and within 4 seconds close the door: the timer

of time between 1 and 12 hours.

using hot water.

WATER HARDNESS TABLE).

DELAY

zadržite dugme

(3 sekunde).

The start time of the program may be delayed for a period

• Hold down button

The start time of the program may be delayed for a period

appears on the display; each time you press the button,

for 5 seconds, until you hear a beep.

The start time of the program may be delayed for a period

will begin counting down.

1. Press the DELAY button: the corresponding «h» symbol

of time between 1 and 12 hours.

Water Hardness Table

• Switch on the appliance by pressing the ON/OFF button.

The start time of the program may be delayed for a period

the time (1h, 2h, etc. up to max. 12h) from the start of

of time between 1 and 12 hours.

appears on the display; each time you press the button,

3. Once this time has elapsed, the indicator light «h»

DELAY

of time between 1 and 12 hours.

the selected wash cycle will be increased.

•

The current selection level number and the salt indicator light

OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL).

1. Press the DELAY button: the corresponding «h» symbol

the time (1h, 2h, etc. up to max. 12h) from the start of

1. Press the DELAY button: the corresponding «h» symbol

Level

switches off and the wash cycle begins.

2. Select the wash program, press the START/PAUSE

The start time of the program may be delayed for a period

Da biste podesili odloženo pokretanje

appears on the display; each time you press the button,

German degrees

1. Press the DELAY button: the corresponding «h» symbol

appears on the display; each time you press the button,

the selected wash cycle will be increased.

If an option is not compatible with the selected program see PROGRAMS TABLE, the corresponding LED

ENGLISH

of time between 1 and 12 hours.

button and within 4 seconds close the door: the timer

•

Press button

to select the desired hardness level (see

To adjust the delay time and select a shorter period of time,

the time (1h, 2h, etc. up to max. 12h) from the start of

DELAY

the time (1h, 2h, etc. up to max. 12h) from the start of

appears on the display; each time you press the button,

the time (1h, 2h, etc. up to max. 12h) from the start of

and beeps will sound. The option will not be enabled.

Soft

2. Select the wash program, press the START/PAUSE

the time (1h, 2h, etc. up to max. 12h) from the start of

will begin counting down.

WATER HARDNESS TABLE).

the selected wash cycle will be increased.

the time (1h, 2h, etc. up to max. 12h) from the start of

press the DELAY button. To cancel it, press the button

the selected wash cycle will be increased.

1. Press the DELAY button: the corresponding «h» symbol

the selected wash cycle will be increased.

button and within 4 seconds close the door: the timer

The start time of the program may be delayed for a period

Medium

3. Once this time has elapsed, the indicator light «h»

HALF LOAD

2. Select the wash program, press the START/PAUSE

the selected wash cycle will be increased.

appears on the display; each time you press the button,

2. Select the wash program, press the START/PAUSE

will begin counting down.

of time between 1 and 12 hours.

repeatedly until the selected delayed start indicator light

Water Hardness Table

Da biste podesili funkciju polupunog pranja

switches off and the wash cycle begins.

Average

button and within 4 seconds close the door: the timer

If there are not many dishes to be washed, a half load

2. Select the wash program, press the START/PAUSE

button and within 4 seconds close the door: the timer

the time (1h, 2h, etc. up to max. 12h) from the start of

3. Once this time has elapsed, the indicator light «h»

button and within 4 seconds close the door: the timer

«h» switches off.

1. Press the DELAY button: the corresponding «h» symbol

To adjust the delay time and select a shorter period of time,

will begin counting down.

cycle may be used in order to save water, electricity and

will begin counting down.

button and within 4 seconds close the door: the timer

will begin counting down.

the selected wash cycle will be increased.

Level

will begin counting down.

switches off and the wash cycle begins.

Hard

appears on the display; each time you press the button,

press the DELAY button. To cancel it, press the button

The DELAY function cannot be set once a wash cycle

detergent. Select the program and press the HALF LOAD

3. Once this time has elapsed, the indicator light «h»

will begin counting down.

2. Select the wash program, press the START/PAUSE

3. Once this time has elapsed, the indicator light «h»

To adjust the delay time and select a shorter period of time,

3. Once this time has elapsed, the indicator light «h»

TABLET (Tab)

DELAY

the time (1h, 2h, etc. up to max. 12h) from the start of

Very hard

button: the indicator light will light up. Press the HALF

repeatedly until the selected delayed start indicator light

switches off and the wash cycle begins.

Soft

has been started.

3. Once this time has elapsed, the indicator light «h»

switches off and the wash cycle begins.

button and within 4 seconds close the door: the timer

press the DELAY button. To cancel it, press the button

switches off and the wash cycle begins.

LOAD button to deselect this option.

the selected wash cycle will be increased.

«h» switches off.

To adjust the delay time and select a shorter period of time,

This setting allows you to optimize the performance of

To adjust the delay time and select a shorter period of time,

The start time of the program may be delayed for a period

switches off and the wash cycle begins.

To adjust the delay time and select a shorter period of time,

will begin counting down.

repeatedly until the selected delayed start indicator light

To adjust the delay time and select a shorter period of time,

Medium

Remember to halve the amount of detergent.

2. Select the wash program, press the START/PAUSE

• Switch off the appliance by pressing the ON/OFF button.

The DELAY function cannot be set once a wash cycle

the program according to the type of detergent used.

press the DELAY button. To cancel it, press the button

of time between 1 and 12 hours.

press the DELAY button. To cancel it, press the button

To adjust the delay time and select a shorter period of time,

3. Once this time has elapsed, the indicator light «h»

press the DELAY button. To cancel it, press the button

«h» switches off.

press the DELAY button. To cancel it, press the button

Tabela programa

has been started.

button and within 4 seconds close the door: the timer

Setting is complete!

Average

repeatedly until the selected delayed start indicator light

Press the START/PAUSE button for 3 seconds (the

repeatedly until the selected delayed start indicator light

press the DELAY button. To cancel it, press the button

repeatedly until the selected delayed start indicator light

switches off and the wash cycle begins.

The DELAY function cannot be set once a wash cycle

repeatedly until the selected delayed start indicator light

1. Press the DELAY button: the corresponding «h» symbol

will begin counting down.

corresponding symbol will light up) if you use combined

«h» switches off.

repeatedly until the selected delayed start indicator light

To adjust the delay time and select a shorter period of time,

has been started.

«h» switches off.

Hard

«h» switches off.

appears on the display; each time you press the button,

3. Once this time has elapsed, the indicator light «h»

The DELAY function cannot be set once a wash cycle

detergents in tablet form (rinse aid, salt and detergent in

FILLING THE RINSE AID DISPENSER

The DELAY function cannot be set once a wash cycle

«h» switches off.

The DELAY function cannot be set once a wash cycle

press the DELAY button. To cancel it, press the button

The DELAY function cannot be set once a wash cycle

the time (1h, 2h, etc. up to max. 12h) from the start of

Very hard

switches off and the wash cycle begins.

has been started.

1 dose).

The DELAY function cannot be set once a wash cycle

has been started.

repeatedly until the selected delayed start indicator light

has been started.

Rinse aid makes dish DRYING easier. The rinse aid dispenser A

the selected wash cycle will be increased.

To adjust the delay time and select a shorter period of time,

If you use powder or liquid detergent, this option

has been started.

«h» switches off.

should be filled when the RINSE AID REFILL indicator light

2. Select the wash program, press the START/PAUSE

• Switch off the appliance by pressing the ON/OFF button.

press the DELAY button. To cancel it, press the button

Program

should be off.

The DELAY function cannot be set once a wash cycle

button and within 4 seconds close the door: the timer

in the control panel is lit.

Setting is complete!

repeatedly until the selected delayed start indicator light

Program

has been started.

will begin counting down.

«h» switches off.

3. Once this time has elapsed, the indicator light «h»

Program

The DELAY function cannot be set once a wash cycle

FILLING THE RINSE AID DISPENSER

switches off and the wash cycle begins.

has been started.

Rinse aid makes dish DRYING easier. The rinse aid dispenser A

Program

Eco

To adjust the delay time and select a shorter period of time,

Program

Eco

1 Eco

should be filled when the RINSE AID REFILL indicator light

Program

press the DELAY button. To cancel it, press the button

Eco

in the control panel is lit.

repeatedly until the selected delayed start indicator light

To adjust the delay time and select a shorter period of time,

2 Conventional

Conventional

Program

«h» switches off.

press the DELAY button. To cancel it, press the button

Eco

wash

Eco

wash and dry

Eco

Conventional

The DELAY function cannot be set once a wash cycle

repeatedly until the selected delayed start indicator light

wash and dry

Eco

and dry

«h» switches off.

has been started.

wash and dry

Program

Conventional

(Konvencionalno

Conventional

The DELAY function cannot be set once a wash cycle

Intensive

Conventional

1. Open the dispenser B by pressing and pulling up the tab on

Eco

has been started.

wash and dry

Conventional

wash and dry

pranje i sušenje)

wash and dry

Intensive

wash and dry

Intensive

the lid.

1. Go to the Dishwasher software menu pressing and holding

wash and dry

2. Carefully introduce the rinse aid as far as the maximum

button (6 sec).

3 Intensive

Fast

Conventional

Intensive

Eco

Intensive

2. You switched to NaturalDry Control Menu, you could change

(110 ml) reference notch of the filling space - avoid spilling it.

(Intenzivno)

wash and dry

Fast

Intensive

status of NaturalDry functionality by pressing

If this happens, clean the spill immediately with a dry cloth.

Fast

Program

Sanitizing

– enabled

Conventional

4 Fast Wash (Brzo

3. Press the lid down until you hear a click to close it.

Fast

1. Open the dispenser B by pressing and pulling up the tab on

Fast

Intensive

To confirm the change and exit from the Control Menu please

NEVER pour the rinse aid directly into the tub.

wash and dry

pranje)

Sanitizing

Fast

the lid.

press and hold

button (3 sec).

Sanitizing

Pre-Wash

2. Carefully introduce the rinse aid as far as the maximum

5 Sanitizing

Sanitizing

Eco

Intensive

Sanitizing

Fast

(110 ml) reference notch of the filling space - avoid spilling it.

(Dezinfikovanje)

Pre-Wash

Sanitizing

If this happens, clean the spill immediately with a dry cloth.

Self-Clean

Conventional

6 Pre-Wash

3. Press the lid down until you hear a click to close it.

Pre-Wash

Fast

Pre-Wash

Sanitizing

wash and dry

NEVER pour the rinse aid directly into the tub.

(Pretpranje)

Self-Clean

Pre-Wash

7 Self-Clean

Self-Clean

Sanitizing

Self-Clean

Intensive

Pre-Wash

Self-Clean

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.

(Samočišćenje)

Self-Clean

Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.

address: dw_test_support@whirlpool.com

Pre-Wash

Podaci programa ECO se mere u laboratorijskim uslovima u skladu sa evropskim standardom EN 60436:2019.

Fast

Self-Clean

Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.

Pre-treatment of the dishes is not needed before any of the programs.

Napomena za laboratorije za testiranje: Za informacije o komparativnim EN uslovima testiranja, pošaljite e-poruku na sledeću adresu: dw_test_

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.

address: dw_test_support@whirlpool.com

*) Not all options can be used simultaneously.

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.

*) Not all options can be used simultaneously.

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.

Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following

support@whirlpool.com

Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following

Pre-treatment of the dishes is not needed before any of the programs.

Self-Clean

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.

Sanitizing

address: dw_test_support@whirlpool.com

**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many

address: dw_test_support@whirlpool.com

Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following

address: dw_test_support@whirlpool.com

Prethodno tretiranje posuđa nije potrebno ni za jedan program.

*) Not all options can be used simultaneously.

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.

address: dw_test_support@whirlpool.com

Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following

Pre-treatment of the dishes is not needed before any of the programs.

factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of

Pre-treatment of the dishes is not needed before any of the programs.

*) Ne mogu se sve opcije koristiti istovremeno.

**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many

load, load balancing, additional selected options and sensor calibration.

*) Not all options can be used simultaneously.

Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following

Pre-treatment of the dishes is not needed before any of the programs.

address: dw_test_support@whirlpool.com

*) Not all options can be used simultaneously.

Pre-Wash

*) Not all options can be used simultaneously.

**) Vrednosti navedene za programe koji nisu eco program su samo indikativne. Stvarno vreme može da varira u zavisnosti od mnogih faktora

factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of

address: dw_test_support@whirlpool.com

**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many

*) Not all options can be used simultaneously.

Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W

**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.

**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many

load, load balancing, additional selected options and sensor calibration.

Pre-treatment of the dishes is not needed before any of the programs.

kao što su temperatura, količina deterdženta, količina i vrsta posuđa, balansiranje posuđa, dodatne izabrane opcije i kalibracija senzora.

factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of

Pre-treatment of the dishes is not needed before any of the programs.

factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of

**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many

factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of

Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following

1. ECO – Eco program je pogodan za čišćenje normalno uprljanog posuđa, jer je u tu svrhu najefikasniji program u pogledu kombinovane

Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W

*) Not all options can be used simultaneously.

Self-Clean

load, load balancing, additional selected options and sensor calibration.

*) Not all options can be used simultaneously.

load, load balancing, additional selected options and sensor calibration.

factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of

load, load balancing, additional selected options and sensor calibration.

PROGRAMS DESCRIPTION

address: dw_test_support@whirlpool.com

load, load balancing, additional selected options and sensor calibration.

potrošnje vode i energije i zato što se koristi za utvrđivanje usaglašenosti sa EU zakonom o eko-dizajnu.

**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many

load, load balancing, additional selected options and sensor calibration.

Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W

Pre-treatment of the dishes is not needed before any of the programs.

Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W

PROGRAMS DESCRIPTION

2. CONVENTIONAL WASH AND DRY (KONVENCIONALNO PRANJE I SUŠENJE) – Mešovita zaprljanost. Za normalno zaprljano posuđe sa

factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of

Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W

*) Not all options can be used simultaneously.

sasušenim ostacima hrane.

load, load balancing, additional selected options and sensor calibration.

PROGRAMS DESCRIPTION

**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many

load, load balancing, additional selected options and sensor calibration.

PROGRAMS DESCRIPTION

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.

Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W

PROGRAMS DESCRIPTION

factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of

Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following

Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W

load, load balancing, additional selected options and sensor calibration.

address: dw_test_support@whirlpool.com

PROGRAMS DESCRIPTION

Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W

Pre-treatment of the dishes is not needed before any of the programs.

ENGLISH

button.

Make sure the cap is screwed on tightly, so that no detergent can

get into the container during the wash program (this could damage

the water softener beyond repair).

As soon as this procedure is complete, run a program without

loading. The "Pre-Wash" program alone is NOT

Residual saline solution or grains of salt can lead to corrosion,

irreparably damaging the stainless steel components.

The guarantee is not applicable if faults are caused by such

circumstances.

heating element may be damaged as a result.

Whenever you need to add salt, it is mandatory to complete

the procedure before the beginning of the washing cycle.

SETTING THE WATER HARDNESS

To allow the water softener to work in a perfect way, it is essential

that the water hardness setting is based on the actual water hard-

ness in your house. This information can be obtained from your local

water supplier. The factory setting is for average (3) water hardness.

• Switch on the appliance by pressing the ON/OFF button.

DELAY

• Switch off the appliance by pressing the ON/OFF button.

ENGLISH

• Hold down button

The start time of the program may be delayed for a period

• Switch on the appliance by pressing the ON/OFF button.

of time between 1 and 12 hours.

•

The current selection level number and the salt indicator light

1. Press the DELAY button: the corresponding «h» symbol

DELAY

appears on the display; each time you press the button,

ENGLISH

•

Press button

DELAY

The start time of the program may be delayed for a period

the time (1h, 2h, etc. up to max. 12h) from the start of

WATER HARDNESS TABLE).

of time between 1 and 12 hours.

the selected wash cycle will be increased.

The start time of the program may be delayed for a period

°dH

°fH

of time between 1 and 12 hours.

2. Select the wash program, press the START/PAUSE

French degrees

1. Press the DELAY button: the corresponding «h» symbol

button and within 4 seconds close the door: the timer

DELAY

appears on the display; each time you press the button,

0 - 6

0 - 10

appears on the display; each time you press the button,

ENGLISH

will begin counting down.

Level

DELAY

the time (1h, 2h, etc. up to max. 12h) from the start of

The start time of the program may be delayed for a period

7 - 11

11 - 20

3. Once this time has elapsed, the indicator light «h»

the selected wash cycle will be increased.

The start time of the program may be delayed for a period

of time between 1 and 12 hours.

rapidly 3 times

switches off and the wash cycle begins.

2. Select the wash program, press the START/PAUSE

of time between 1 and 12 hours.

12 - 17

21 - 30

2. Select the wash program, press the START/PAUSE

ENGLISH

button and within 4 seconds close the door: the timer

1. Press the DELAY button: the corresponding «h» symbol

To adjust the delay time and select a shorter period of time,

°dH

°fH

1. Press the DELAY button: the corresponding «h» symbol

Medium

button and within 4 seconds close the door: the timer

18 - 34

will begin counting down.

31 - 60

appears on the display; each time you press the button,

press the DELAY button. To cancel it, press the button

appears on the display; each time you press the button,

German degrees

French degrees

will begin counting down.

3. Once this time has elapsed, the indicator light «h»

Average

DELAY

the time (1h, 2h, etc. up to max. 12h) from the start of

repeatedly until the selected delayed start indicator light

35 - 50

61 - 90

switches off and the wash cycle begins.

0 - 6

0 - 10

3. Once this time has elapsed, the indicator light «h»

Da biste podesili funkciju Multi tab

ENGLISH

the selected wash cycle will be increased.

The start time of the program may be delayed for a period

«h» switches off.

To adjust the delay time and select a shorter period of time,

switches off and the wash cycle begins.

2. Select the wash program, press the START/PAUSE

of time between 1 and 12 hours.

7 - 11

11 - 20

press the DELAY button. To cancel it, press the button

2. Select the wash program, press the START/PAUSE

The DELAY function cannot be set once a wash cycle

button and within 4 seconds close the door: the timer

To adjust the delay time and select a shorter period of time,

Very hard

DELAY

repeatedly until the selected delayed start indicator light

1. Press the DELAY button: the corresponding «h» symbol

has been started.

button and within 4 seconds close the door: the timer

will begin counting down.

12 - 17

21 - 30

press the DELAY button. To cancel it, press the button

ENGLISH

«h» switches off.

appears on the display; each time you press the button,

The start time of the program may be delayed for a period

3. Once this time has elapsed, the indicator light «h»

will begin counting down.

The DELAY function cannot be set once a wash cycle

repeatedly until the selected delayed start indicator light

the time (1h, 2h, etc. up to max. 12h) from the start of

• Switch off the appliance by pressing the ON/OFF button.

18 - 34

31 - 60

of time between 1 and 12 hours.

switches off and the wash cycle begins.

3. Once this time has elapsed, the indicator light «h»

has been started.

the selected wash cycle will be increased.

«h» switches off.

To adjust the delay time and select a shorter period of time,

Setting is complete!

DELAY

1. Press the DELAY button: the corresponding «h» symbol

35 - 50

61 - 90

switches off and the wash cycle begins.

2. Select the wash program, press the START/PAUSE

press the DELAY button. To cancel it, press the button

The DELAY function cannot be set once a wash cycle

ENGLISH

appears on the display; each time you press the button,

The start time of the program may be delayed for a period

button and within 4 seconds close the door: the timer

To adjust the delay time and select a shorter period of time,

repeatedly until the selected delayed start indicator light

the time (1h, 2h, etc. up to max. 12h) from the start of

Faza

has been started.

of time between 1 and 12 hours.

will begin counting down.

FILLING THE RINSE AID DISPENSER

«h» switches off.

press the DELAY button. To cancel it, press the button

the selected wash cycle will be increased.

DELAY

3. Once this time has elapsed, the indicator light «h»

sušenja

1. Press the DELAY button: the corresponding «h» symbol

The DELAY function cannot be set once a wash cycle

2. Select the wash program, press the START/PAUSE

repeatedly until the selected delayed start indicator light

Rinse aid makes dish DRYING easier. The rinse aid dispenser A

switches off and the wash cycle begins.

Program

appears on the display; each time you press the button,

has been started.

The start time of the program may be delayed for a period

button and within 4 seconds close the door: the timer

«h» switches off.

To adjust the delay time and select a shorter period of time,

Program

should be filled when the RINSE AID REFILL indicator light

the time (1h, 2h, etc. up to max. 12h) from the start of

of time between 1 and 12 hours.

will begin counting down.

press the DELAY button. To cancel it, press the button

The DELAY function cannot be set once a wash cycle

the selected wash cycle will be increased.

in the control panel is lit.

DELAY

3. Once this time has elapsed, the indicator light «h»

1. Press the DELAY button: the corresponding «h» symbol

repeatedly until the selected delayed start indicator light

2. Select the wash program, press the START/PAUSE

has been started.

switches off and the wash cycle begins.

appears on the display; each time you press the button,

The start time of the program may be delayed for a period

«h» switches off.

button and within 4 seconds close the door: the timer

50°

Eco

50°

To adjust the delay time and select a shorter period of time,

Eco

the time (1h, 2h, etc. up to max. 12h) from the start of

50 °

50°

of time between 1 and 12 hours.

The DELAY function cannot be set once a wash cycle

will begin counting down.

Program

press the DELAY button. To cancel it, press the button

the selected wash cycle will be increased.

has been started.

1. Press the DELAY button: the corresponding «h» symbol

3. Once this time has elapsed, the indicator light «h»

50°

Program

repeatedly until the selected delayed start indicator light

2. Select the wash program, press the START/PAUSE

Conventional

switches off and the wash cycle begins.

appears on the display; each time you press the button,

Conventional

55°

«h» switches off.

button and within 4 seconds close the door: the timer

wash and dry

To adjust the delay time and select a shorter period of time,

55°

the time (1h, 2h, etc. up to max. 12h) from the start of

The DELAY function cannot be set once a wash cycle

50°

will begin counting down.

wash and dry

55°

50°

press the DELAY button. To cancel it, press the button

the selected wash cycle will be increased.

has been started.

3. Once this time has elapsed, the indicator light «h»

Eco

50°

Eco

55°

repeatedly until the selected delayed start indicator light

55 °

50°

2. Select the wash program, press the START/PAUSE

Intensive

65°

switches off and the wash cycle begins.

«h» switches off.

Program

button and within 4 seconds close the door: the timer

Intensive

65°

To adjust the delay time and select a shorter period of time,

The DELAY function cannot be set once a wash cycle

55°

will begin counting down.

55°

Program

Conventional

55°

50°

press the DELAY button. To cancel it, press the button

Conventional

55°

has been started.

Fast

50°

65°

3. Once this time has elapsed, the indicator light «h»

wash and dry

65°

55°

repeatedly until the selected delayed start indicator light

wash and dry

switches off and the wash cycle begins.

«h» switches off.

Fast

50°

1. Open the dispenser B by pressing and pulling up the tab on

To adjust the delay time and select a shorter period of time,

65°

Eco

The DELAY function cannot be set once a wash cycle

Intensive

65°

50°

65°

50°

Eco

Sanitizing

Program

65°

65 °

50°

65°

55°

press the DELAY button. To cancel it, press the button

the lid.

has been started.

Intensive

50°

65°

repeatedly until the selected delayed start indicator light

button:

50°

2. Carefully introduce the rinse aid as far as the maximum

Conventional

«h» switches off.

Sanitizing

Fast

65°

50°

65°

– disabled

Conventional

Pre-Wash

55°

50°

(110 ml) reference notch of the filling space - avoid spilling it.

The DELAY function cannot be set once a wash cycle

wash and dry

50°

55°

Eco

50°

50 °

Program

–

50°

65°

wash and dry

has been started.

65°

If this happens, clean the spill immediately with a dry cloth.

Fast

50°

Sanitizing

65°

Self-Clean

65°

Intensive

65°

Conventional

3. Press the lid down until you hear a click to close it.

65°

Pre-Wash

55°

65°

Intensive

wash and dry

65°

Program

NEVER pour the rinse aid directly into the tub.

50°

Eco

65°

65 °

50°

Sanitizing

65°

Pre-Wash

Fast

50°

Intensive

65°

Conventional

Self-Clean

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.

65°

55°

Fast

50°

wash and dry

55°

Program

Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following

Eco

–

65°

–

50°

Self-Clean

65°

Sanitizing

65°

Pre-Wash

address: dw_test_support@whirlpool.com

Fast

50°

Intensive

65°

Pre-treatment of the dishes is not needed before any of the programs.

Conventional

55°

65°

Sanitizing

65°

*) Not all options can be used simultaneously.

Pre-Wash

65°

wash and dry

65°

Eco

65 °

–

50°

65°

Sanitizing

65°

**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.

Self-Clean

65°

Fast

50°

factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of

Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following

Intensive

65°

Conventional

Self-Clean

65°

load, load balancing, additional selected options and sensor calibration.

address: dw_test_support@whirlpool.com

55°

Pre-Wash

50°

wash and dry

65°

Pre-treatment of the dishes is not needed before any of the programs.

Sanitizing

65°

Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W

Fast

50°

*) Not all options can be used simultaneously.

Intensive

65°

Self-Clean

65°

**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many

PROGRAMS DESCRIPTION

Self-Clean

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.

65°

Pre-Wash

factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of

Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following

Sanitizing

65°

load, load balancing, additional selected options and sensor calibration.

Fast

50°

address: dw_test_support@whirlpool.com

Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W

Self-Clean

65°

Pre-treatment of the dishes is not needed before any of the programs.

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.

Pre-Wash

*) Not all options can be used simultaneously.

Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following

Sanitizing

65°

PROGRAMS DESCRIPTION

**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many

address: dw_test_support@whirlpool.com

factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of

Self-Clean

65°

Pre-treatment of the dishes is not needed before any of the programs.

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.

65°

Pre-Wash

load, load balancing, additional selected options and sensor calibration.

*) Not all options can be used simultaneously.

Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following

Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W

**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many

address: dw_test_support@whirlpool.com

factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of

Self-Clean

65°

Pre-treatment of the dishes is not needed before any of the programs.

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.

PROGRAMS DESCRIPTION

load, load balancing, additional selected options and sensor calibration.

*) Not all options can be used simultaneously.

Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following

Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W

**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many

address: dw_test_support@whirlpool.com

factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of

Pre-treatment of the dishes is not needed before any of the programs.

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.

PROGRAMS DESCRIPTION

Da biste preuzeli celu verziju, posetite www.ikea.com

load, load balancing, additional selected options and sensor calibration.

*) Not all options can be used simultaneously.

Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following

Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W

**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many

address: dw_test_support@whirlpool.com

factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of

MODIFYING A RUNNING PROGRAM

If a wrong program was selected, it is possible to change it, pro-

vided that it has only just begun: open the door, press and hold

the ON/OFF button, the machine will switch off.

Switch the machine back on using the ON/OFF button and select

the new wash cycle and any desired options; Start the wash cycle

by pressing START/Pause button and closing the door within 4 sec.

ADJUSTING THE DOSAGE OF RINSE AID

If you are not completely satisfied with the drying results, you can

ADDING EXTRA CROCKERY

adjust the quantity of rinse aid used.

Without switching off the machine, open the door (START/Pause

• Switch the dishwasher on using the ON/OFF button.

led starts blinking) (be ware of HOT steam!) and place the

• Switch it off using the ON/OFF button.

crockery inside the dishwasher. Press the START/Pause button

and close the door within 4 sec., the cycle will resume from the

• Press button

three times - a beep will be heard.

ADJUSTING THE DOSAGE OF RINSE AID

point at which it was interrupted.

• Switch it on using the ON/OFF button.

If you are not completely satisfied with the drying results, you can

•

The current selection level number and rinse aid indicator light flash.

ACCIDENTAL INTERRUPTIONS

adjust the quantity of rinse aid used.

•

Press button

to select the level of rinse aid quantity to be

If the door is opened during the wash cycle, or if there is a power

• Switch the dishwasher on using the ON/OFF button.

supplied.

cut, the cycle stops. Press the START/Pause button and close

• Switch it off using the ON/OFF button.

the door within 4 sec., the cycle will resume from the point at

• Press button

three times - a beep will be heard.

Setting is complete!

Conventional wash and dry

which it was interrupted.

• Switch it on using the ON/OFF button.

(Konvencionalno pranje i sušenje)

If the rinse aid level is set to ZERO (ECO), no rinse aid will be

•

The current selection level number and rinse aid indicator light flash.

supplied. The LOW RINSE AID indicator light will not be lit if you

•

Press button

to select the level of rinse aid quantity to be

run out of rinse aid. A maximum of 5 levels can be set according to

supplied.

Intensive (Intenzivno) 65 °

the dishwasher model. The factory setting is specific to the model,

• Switch it off using the ON/OFF button.

please follow instruction above to check this for your machine.

Setting is complete!

Fast wash (Brzo pranje) 50°

• If you see bluish streaks on the dishes, set a low number (1-2).

If the rinse aid level is set to ZERO (ECO), no rinse aid will be

• If there are drops of water or limescale marks on the dishes,

supplied. The LOW RINSE AID indicator light will not be lit if you

Sanitizing (Dezinfikovanje) 65°

set a high number (3-4).

NaturalDry

run out of rinse aid. A maximum of 5 levels can be set according to

Pre-Wash (Pretpranje)

the dishwasher model. The factory setting is specific to the model,

Door opening system NaturalDry is a convection drying system

FILLING THE DETERGENT DISPENSER

please follow instruction above to check this for your machine.

which automatically opens the door during/after drying phase to

Self-Clean (Samočišćenje) 65°

• If you see bluish streaks on the dishes, set a low number (1-2).

ensure exceptional drying performance every day. Door opens at

• If there are drops of water or limescale marks on the dishes,

dishwashers.

for 5 seconds, until you hear a beep.

set a high number (3-4).

the temperature that is safe to your kitchen furniture.

To achieve the best washing and drying results, the combined

NaturalDry

As additional steam protection, special designed protection foil is

useof detergent, rinse aid liquid and refined salt is required.

We recommend using detergents that do not contain phosphates

Door opening system NaturalDry is a convection drying system

added together with the dishwasher. To see how to mount protec-

Door opening system NaturalDry is a convection drying system

FILLING THE DETERGENT DISPENSER

NaturalDry

or chlorine, as these products are harmful to the environment.

which automatically opens the door during/after drying phase to

tion foil please refer to (INSTALLATION GUIDE).

to select the desired hardness level (see

Door opening system NaturalDry is a convection drying system

NaturalDry

Good washing results also depend on the correct amount of

NaturalDry

ensure exceptional drying performance every day. Door opens at

Funkcije se mogu izabrati direktno pritiskanjem odgovarajućeg

NaturalDry

NaturalDry functionality could be disabled by the user as follows:

which automatically opens the door during/after drying phase to

dishwashers.

detergent being used.

the temperature that is safe to your kitchen furniture.

NaturalDry

Door opening system NaturalDry is a convection drying system

dugmeta (pogledajte KONTROLNA TABLA).

Door opening system NaturalDry is a convection drying system

ensure exceptional drying performance every day. Door opens at

Door opening system NaturalDry is a convection drying system

To achieve the best washing and drying results, the combined

1. Go to the Dishwasher software menu pressing and holding

NaturalDry

As additional steam protection, special designed protection foil is

Water Hardness Table

which automatically opens the door during/after drying phase to

Exceeding the stated amount does not result in a more effective

which automatically opens the door during/after drying phase to

Door opening system NaturalDry is a convection drying system

which automatically opens the door during/after drying phase to

the temperature that is safe to your kitchen furniture.

which automatically opens the door during/after drying phase to

useof detergent, rinse aid liquid and refined salt is required.

added together with the dishwasher. To see how to mount protec-

Door opening system NaturalDry is a convection drying system

added together with the dishwasher. To see how to mount protec-

button (6 sec).

NaturalDry

ensure exceptional drying performance every day. Door opens at

wash and increases environmental pollution.

which automatically opens the door during/after drying phase to

ensure exceptional drying performance every day. Door opens at

As additional steam protection, special designed protection foil is

°dH

ensure exceptional drying performance every day. Door opens at

Ako funkcija nije kompatibilna sa izabranim programom

which automatically opens the door during/after drying phase to

We recommend using detergents that do not contain phosphates

tion foil please refer to (INSTALLATION GUIDE).

2. You switched to NaturalDry Control Menu, you could change

the temperature that is safe to your kitchen furniture.

The amount can be adjusted to the soil level. In the case of

ensure exceptional drying performance every day. Door opens at

the temperature that is safe to your kitchen furniture.

added together with the dishwasher. To see how to mount protec-

ensure exceptional drying performance every day. Door opens at

Door opening system NaturalDry is a convection drying system

the temperature that is safe to your kitchen furniture.

German degrees

(pogledajte TABELU PROGRAMA), odgovarajući LED indikator

or chlorine, as these products are harmful to the environment.

NaturalDry functionality could be disabled by the user as follows:

TABLET (Tab)

As additional steam protection, special designed protection foil is

the temperature that is safe to your kitchen furniture.

As additional steam protection, special designed protection foil is

the temperature that is safe to your kitchen furniture.

normally soiled items, use approximately either 35g (powder

tion foil please refer to (INSTALLATION GUIDE).

As additional steam protection, special designed protection foil is

status of NaturalDry functionality by pressing

which automatically opens the door during/after drying phase to

As additional steam protection, special designed protection foil is

NaturalDry

Soft

0 - 6

Good washing results also depend on the correct amount of

1. Go to the Dishwasher software menu pressing and holding

treperi brzo 3 puta i emitovaće se zvučni signali. Funkcija

As additional steam protection, special designed protection foil is

added together with the dishwasher. To see how to mount protec-

NaturalDry

added together with the dishwasher. To see how to mount protec-

This setting allows you to optimize the performance of

As additional steam protection, special designed protection foil is

added together with the dishwasher. To see how to mount protec-

NaturalDry functionality could be disabled by the user as follows:

detergent) or 35ml (liquid detergent) and additional tea spoon of

added together with the dishwasher. To see how to mount protec-

ensure exceptional drying performance every day. Door opens at

added together with the dishwasher. To see how to mount protec-

– enabled

detergent being used.

button (6 sec).

added together with the dishwasher. To see how to mount protec-

button (6 sec).

Door opening system NaturalDry is a convection drying system

neće biti omogućena.

tion foil please refer to (INSTALLATION GUIDE).

7 - 11

tion foil please refer to (INSTALLATION GUIDE).

the program according to the type of detergent used.

Door opening system NaturalDry is a convection drying system

added together with the dishwasher. To see how to mount protec-

tion foil please refer to (INSTALLATION GUIDE).

1. Go to the Dishwasher software menu pressing and holding

detergent directly inside the tub. If tablets are used, one tablet

tion foil please refer to (INSTALLATION GUIDE).

the temperature that is safe to your kitchen furniture.

tion foil please refer to (INSTALLATION GUIDE).

2. You switched to NaturalDry Control Menu, you could change

To confirm the change and exit from the Control Menu please

which automatically opens the door during/after drying phase to

Press the START/PAUSE button for 3 seconds (the

Exceeding the stated amount does not result in a more effective

NaturalDry functionality could be disabled by the user as follows:

tion foil please refer to (INSTALLATION GUIDE).

NaturalDry functionality could be disabled by the user as follows:

button (6 sec).

NaturalDry functionality could be disabled by the user as follows:

As additional steam protection, special designed protection foil is

will be enough.

NaturalDry functionality could be disabled by the user as follows:

12 - 17

status of NaturalDry functionality by pressing

ensure exceptional drying performance every day. Door opens at

status of NaturalDry functionality by pressing

corresponding symbol will light up) if you use combined

ensure exceptional drying performance every day. Door opens at

press and hold

1. Go to the Dishwasher software menu pressing and holding

wash and increases environmental pollution.

NaturalDry functionality could be disabled by the user as follows:

1. Go to the Dishwasher software menu pressing and holding

2. You switched to NaturalDry Control Menu, you could change

1. Go to the Dishwasher software menu pressing and holding

added together with the dishwasher. To see how to mount protec-

1. Go to the Dishwasher software menu pressing and holding

If the crockery is only lightly soiled or if it has been rinsed with

the temperature that is safe to your kitchen furniture.

– enabled

detergents in tablet form (rinse aid, salt and detergent in

button (6 sec).

Hard

the temperature that is safe to your kitchen furniture.

18 - 34

the temperature that is safe to your kitchen furniture.

button (6 sec).

The amount can be adjusted to the soil level. In the case of

1. Go to the Dishwasher software menu pressing and holding

status of NaturalDry functionality by pressing

button (6 sec).

tion foil please refer to (INSTALLATION GUIDE).

button (6 sec).

As additional steam protection, special designed protection foil is

button (6 sec).

water before being placed in the dishwasher, reduce the amount

1 dose).

To confirm the change and exit from the Control Menu please

2. You switched to NaturalDry Control Menu, you could change

To confirm the change and exit from the Control Menu please

NaturalDry

As additional steam protection, special designed protection foil is

2. You switched to NaturalDry Control Menu, you could change

added together with the dishwasher. To see how to mount protec-

normally soiled items, use approximately either 35g (powder

button (6 sec).

2. You switched to NaturalDry Control Menu, you could change

– enabled

NaturalDry functionality could be disabled by the user as follows:

– disabled

2. You switched to NaturalDry Control Menu, you could change

35 - 50

2. You switched to NaturalDry Control Menu, you could change

NaturalDry

status of NaturalDry functionality by pressing

of detergent used accordingly (minimum 25 g/ml) e.g. skip the

If you use powder or liquid detergent, this option

press and hold

button (3 sec).

Door opening system NaturalDry is a convection drying system

added together with the dishwasher. To see how to mount protec-

tion foil please refer to (INSTALLATION GUIDE).

added together with the dishwasher. To see how to mount protec-

status of NaturalDry functionality by pressing

2. You switched to NaturalDry Control Menu, you could change

detergent) or 35ml (liquid detergent) and additional tea spoon of

To confirm the change and exit from the Control Menu please

status of NaturalDry functionality by pressing

1. Go to the Dishwasher software menu pressing and holding

– enabled

status of NaturalDry functionality by pressing

should be off.

powder/gel putted inside the tub.

which automatically opens the door during/after drying phase to

Door opening system NaturalDry is a convection drying system

NaturalDry functionality could be disabled by the user as follows:

tion foil please refer to (INSTALLATION GUIDE).

– enabled

To confirm the change and exit from the Control Menu please

– disabled

status of NaturalDry functionality by pressing

detergent directly inside the tub. If tablets are used, one tablet

press and hold

– enabled

button (6 sec).

button (3 sec).

– disabled

– enabled

– disabled

ensure exceptional drying performance every day. Door opens at

1. Go to the Dishwasher software menu pressing and holding

which automatically opens the door during/after drying phase to

NaturalDry

NaturalDry functionality could be disabled by the user as follows:

press and hold

NaturalDry functionality could be disabled by the user as follows:

To confirm the change and exit from the Control Menu please

– enabled

the temperature that is safe to your kitchen furniture.

To confirm the change and exit from the Control Menu please

2. You switched to NaturalDry Control Menu, you could change

will be enough.

To confirm the change and exit from the Control Menu please

button (6 sec).

ensure exceptional drying performance every day. Door opens at

Door opening system NaturalDry is a convection drying system

1. Go to the Dishwasher software menu pressing and holding

press and hold

button (3 sec).

press and hold

As additional steam protection, special designed protection foil is

button (3 sec).

To confirm the change and exit from the Control Menu please

2. You switched to NaturalDry Control Menu, you could change

To confirm the change and exit from the Control Menu please

press and hold

status of NaturalDry functionality by pressing

button (3 sec).

press and hold

button (3 sec).

If the crockery is only lightly soiled or if it has been rinsed with

which automatically opens the door during/after drying phase to

the temperature that is safe to your kitchen furniture.

button (6 sec).

added together with the dishwasher. To see how to mount protec-

button (6 sec).

status of NaturalDry functionality by pressing

press and hold

button (3 sec).

– enabled

Natural

Dostupne

ensure exceptional drying performance every day. Door opens at

water before being placed in the dishwasher, reduce the amount

Available

Duration of

NaturalDry

tion foil please refer to (INSTALLATION GUIDE).

As additional steam protection, special designed protection foil is

– enabled

2. You switched to NaturalDry Control Menu, you could change

the temperature that is safe to your kitchen furniture.

To confirm the change and exit from the Control Menu please

NaturalDry functionality could be disabled by the user as follows:

Dry

of detergent used accordingly (minimum 25 g/ml) e.g. skip the

funkcije (*)

To confirm the change and exit from the Control Menu please

Available

added together with the dishwasher. To see how to mount protec-

Door opening system NaturalDry is a convection drying system

Available

wash pro-

Duration of

status of NaturalDry functionality by pressing

options

As additional steam protection, special designed protection foil is

Duration of

1. Go to the Dishwasher software menu pressing and holding

press and hold

button (3 sec).

which automatically opens the door during/after drying phase to

powder/gel putted inside the tub.

Available

wash pro-

tion foil please refer to (INSTALLATION GUIDE).

added together with the dishwasher. To see how to mount protec-

options

– enabled

options

– enabled

gram

button (6 sec).

Available

ensure exceptional drying performance every day. Door opens at

wash pro-

NaturalDry

options

tion foil please refer to (INSTALLATION GUIDE).

NaturalDry functionality could be disabled by the user as follows:

To confirm the change and exit from the Control Menu please

2. You switched to NaturalDry Control Menu, you could change

To confirm the change and exit from the Control Menu please

Duration of

(h:min)

the temperature that is safe to your kitchen furniture.

Duration of

NaturalDry functionality could be disabled by the user as follows:

options

gram

Door opening system NaturalDry is a convection drying system

status of NaturalDry functionality by pressing

1. Go to the Dishwasher software menu pressing and holding

press and hold

As additional steam protection, special designed protection foil is

press and hold

button (3 sec).

Duration of

Available

wash pro-

1. Go to the Dishwasher software menu pressing and holding

Available

wash pro-

Available

which automatically opens the door during/after drying phase to

wash pro-

– enabled

(h:min)

added together with the dishwasher. To see how to mount protec-

**)

button (6 sec).

options

Available

gram

wash pro-

options

To confirm the change and exit from the Control Menu please

ensure exceptional drying performance every day. Door opens at

gram

Duration of

options

NaturalDry

gram

options

tion foil please refer to (INSTALLATION GUIDE).

gram

2. You switched to NaturalDry Control Menu, you could change

the temperature that is safe to your kitchen furniture.

press and hold

Available

Duration of

wash pro-

1. Go to the Dishwasher software menu pressing and holding

options

NaturalDry functionality could be disabled by the user as follows:

options

(h:min)

gram

(h:min)

**)

Door opening system NaturalDry is a convection drying system

(h:min)

status of NaturalDry functionality by pressing

2:45

(h:min)

**)

status of NaturalDry functionality by pressing

**)

As additional steam protection, special designed protection foil is

options

button (6 sec).

1. Go to the Dishwasher software menu pressing and holding

Available

which automatically opens the door during/after drying phase to

wash pro-

– enabled

(h:min)

added together with the dishwasher. To see how to mount protec-

– enabled

button (6 sec).

2. You switched to NaturalDry Control Menu, you could change

ensure exceptional drying performance every day. Door opens at

To confirm the change and exit from the Control Menu please

tion foil please refer to (INSTALLATION GUIDE).