IKEA RENGORA Manual page 33

Hide thumbs Also See for RENGORA:

Manual (80 pages)

Owner's manual (48 pages)

Instruction manual (29 pages)

Table Of Contents

Table of Contents

2. SWITCH ON THE DISHWASHER

MODIFYING A RUNNING PROGRAM

Open the door and press the ON/OFF button.

If a wrong program was selected, it is possible to change it, pro-

LOAD THE RACKS (see LOADING THE RACKS)

vided that it has only just begun: open the door, press and hold

FILLING THE DETERGENT DISPENSER

the ON/OFF button, the machine will switch off.

ENGLISH

(see PROGRAMS TABLE).

POLSKI

Switch the machine back on using the ON/OFF button and select

CHOOSE THE PROGRAM AND CUSTOMISE THE CYCLE

the new wash cycle and any desired options; Start the wash cycle

ENGLISH

Select the most appropriate program in accordance with the

by pressing START/Pause button and closing the door within 4 sec.

type of crockery and its soiling level (see PROGRAMS

DESCRIPTION) by pressing the

Make sure the cap is screwed on tightly, so that no detergent can

ADDING EXTRA CROCKERY

Select the desired options (see OPTIONS AND FUNCTIONS).

get into the container during the wash program (this could damage

ENGLISH

Funkcje

Without switching off the machine, open the door (START/Pause

START

the water softener beyond repair).

Make sure the cap is screwed on tightly, so that no detergent can

Start the wash cycle by pressing START/Pause button (led

led starts blinking) (be ware of HOT steam!) and place the

As soon as this procedure is complete, run a program without

get into the container during the wash program (this could damage

is lit) and closing the door within 4 sec. When the program

crockery inside the dishwasher. Press the START/Pause button

loading. The "Pre-Wash" program alone is NOT

the water softener beyond repair).

NATURALDRY

starts you hear a single beep. If the door was not closed within

and close the door within 4 sec., the cycle will resume from the

Residual saline solution or grains of salt can lead to corrosion,

As soon as this procedure is complete, run a program without

System otwierania drzwiczek NaturalDry to konwekcyjny system

4sec., the alarm sound will be played. In this case, open the

Make sure the cap is screwed on tightly, so that no detergent can

point at which it was interrupted.

irreparably damaging the stainless steel components.

loading. The "Pre-Wash" program alone is NOT

door, press START/Pause button and close the door again

suszenia, który automatycznie otwiera drzwiczki podczas/po fazie

get into the container during the wash program (this could damage

The guarantee is not applicable if faults are caused by such

within 4 sec.

Residual saline solution or grains of salt can lead to corrosion,

suszenia, aby zapewnić doskonałe rezultaty suszenia każdego dnia.

the water softener beyond repair).

ACCIDENTAL INTERRUPTIONS

circumstances.

END OF WASH CYCLE

irreparably damaging the stainless steel components.

As soon as this procedure is complete, run a program without

Drzwiczki zostaną otwarte kiedy temperatura spadnie do poziomu

If the door is opened during the wash cycle, or if there is a power

The end of the wash cycle is indicated by beeps and by the

The guarantee is not applicable if faults are caused by such

ENGLISH

loading. The "Pre-Wash" program alone is NOT

bezpiecznego dla mebli kuchennych.

flashing of the wash cycle number on the display. Open the

cut, the cycle stops. Press the START/Pause button and close

circumstances.

Residual saline solution or grains of salt can lead to corrosion,

door and switch off the appliance by pressing the ON/OFF

heating element may be damaged as a result.

Nie wyjmować naczyń zaraz po otwarciu drzwiczek, tylko odczekać w

the door within 4 sec., the cycle will resume from the point at

irreparably damaging the stainless steel components.

button.

Whenever you need to add salt, it is mandatory to complete

which it was interrupted.

celu zapewnienia odpowiedniego wysuszenia.

Wait for a few minutes before removing the crockery - to avoid

The guarantee is not applicable if faults are caused by such

the procedure before the beginning of the washing cycle.

heating element may be damaged as a result.

Funkcja nie może być aktywowana w przypadku wszystkich

burns. Unload the racks, beginning with the lower one.

circumstances.

Whenever you need to add salt, it is mandatory to complete

programów; prosimy zapoznać się z tabelą programów.

SETTING THE WATER HARDNESS

the procedure before the beginning of the washing cycle.

Do zmywarki dołączono specjalnie zaprojektowaną folię ochronną

Functions

To allow the water softener to work in a perfect way, it is essential

heating element may be damaged as a result.

która pełni funkcję dodatkowej ochrony przed parą. Aby zobaczyć

that the water hardness setting is based on the actual water hard-

DELAY

SETTING THE WATER HARDNESS

Whenever you need to add salt, it is mandatory to complete

ENGLISH

jak zamontować osłonę foliową, należy zapoznać się z rozdziałem

ness in your house. This information can be obtained from your local

ENGLISH

1. ECO - Normally soiled crockery. Standard program, the most efficient in terms of its combined energy and water

To allow the water softener to work in a perfect way, it is essential

The start time of the program may be delayed for a period

the procedure before the beginning of the washing cycle.

water supplier. The factory setting is for average (3) water hardness.

consumption.

(INSTRUKCJE MONTAŻU).

that the water hardness setting is based on the actual water hard-

of time between 1 and 12 hours.

2. NORMAL - Mixed soil. For normally soiled dishes with dried food residues.

Użytkownik może wyłączyć funkcję NaturalDry w następujący sposób:

ness in your house. This information can be obtained from your local

ENGLISH

• Switch on the appliance by pressing the ON/OFF button.

SETTING THE WATER HARDNESS

3. INTENSIVE - Program recommended for heavily soiled crockery, especially suitable for pans and saucepans (not to be used

water supplier. The factory setting is for average (3) water hardness.

1. Przejść do menu oprogramowania zmywarki naciskając i

1. Press the DELAY button: the corresponding «h» symbol

• Switch off the appliance by pressing the ON/OFF button.

To allow the water softener to work in a perfect way, it is essential

for delicate items).

przytrzymujący przycisk

(6 sek.).

• Hold down button

for 5 seconds, until you hear a beep.

that the water hardness setting is based on the actual water hard-

appears on the display; each time you press the button,

• Switch on the appliance by pressing the ON/OFF button.

4. PRE-WASH - Use to refresh crockery planned to be washed later. No detergent to be used with this program.

ENGLISH

2. Po przejściu do Menu Sterowania NaturalDry, można zmienić

• Switch on the appliance by pressing the ON/OFF button.

ness in your house. This information can be obtained from your local

DELAY

• Switch off the appliance by pressing the ON/OFF button.

DELAY

the time (1h, 2h, etc. up to max. 12h) from the start of

5. FAST - Normally soiled crockery. Everyday cycle, that ensures optimal cleaning performance in shorter time.

•

ENGLISH

The current selection level number and the salt indicator light

ENGLISH

water supplier. The factory setting is for average (3) water hardness.

status tej funkcji, naciskając przycisk

• Hold down button

The start time of the program may be delayed for a period

the selected wash cycle will be increased.

6. SANITIZING - Normally or heavily soiled crockery, with additional antibacterial wash. Can be used to perform

The start time of the program may be delayed for a period

E – aktywna d – nieaktywna

• Switch on the appliance by pressing the ON/OFF button.

of time between 1 and 12 hours.

maintenance of the dishwasher.

of time between 1 and 12 hours.

• Switch on the appliance by pressing the ON/OFF button.

of time between 1 and 12 hours.

2. Select the wash program, press the START/PAUSE

DELAY

•

Press button

to select the desired hardness level (see

•

The current selection level number and the salt indicator light

Aby zatwierdzić zmianę i wyjść z Menu sterowania, należy

7. SELF- CLEAN - Program to be used to perform maintenance of the dishwasher. It cleans the interior of the appliance

ENGLISH

• Switch off the appliance by pressing the ON/OFF button.

1. Press the DELAY button: the corresponding «h» symbol

WATER HARDNESS TABLE).

1. Press the DELAY button: the corresponding «h» symbol

button and within 4 seconds close the door: the timer

The start time of the program may be delayed for a period

using hot water.

nacisnąć i przytrzymać przycisk

appears on the display; each time you press the button,

• Hold down button

appears on the display; each time you press the button,

ENGLISH

of time between 1 and 12 hours.

•

Press button

will begin counting down.

Water Hardness Table

• Switch on the appliance by pressing the ON/OFF button.

the time (1h, 2h, etc. up to max. 12h) from the start of

DELAY

the time (1h, 2h, etc. up to max. 12h) from the start of

DELAY

the time (1h, 2h, etc. up to max. 12h) from the start of

WATER HARDNESS TABLE).

ENGLISH

1. Press the DELAY button: the corresponding «h» symbol

3. Once this time has elapsed, the indicator light «h»

the selected wash cycle will be increased.

•

The current selection level number and the salt indicator light

the selected wash cycle will be increased.

DELAY

The start time of the program may be delayed for a period

Level

OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL).

appears on the display; each time you press the button,

2. Select the wash program, press the START/PAUSE

switches off and the wash cycle begins.

2. Select the wash program, press the START/PAUSE

of time between 1 and 12 hours.

The start time of the program may be delayed for a period

Aby ustawić opóźniony start

DELAY

the time (1h, 2h, etc. up to max. 12h) from the start of

button and within 4 seconds close the door: the timer

•

Press button

button and within 4 seconds close the door: the timer

If an option is not compatible with the selected program see PROGRAMS TABLE, the corresponding LED

button and within 4 seconds close the door: the timer

To adjust the delay time and select a shorter period of time,

Soft

ENGLISH

of time between 1 and 12 hours.

1. Press the DELAY button: the corresponding «h» symbol

the selected wash cycle will be increased.

will begin counting down.

Level

will begin counting down.

WATER HARDNESS TABLE).

and beeps will sound. The option will not be enabled.

will begin counting down.

press the DELAY button. To cancel it, press the button

appears on the display; each time you press the button,

2. Select the wash program, press the START/PAUSE

Medium

2. Select the wash program, press the START/PAUSE

3. Once this time has elapsed, the indicator light «h»

1. Press the DELAY button: the corresponding «h» symbol

3. Once this time has elapsed, the indicator light «h»

DELAY

the time (1h, 2h, etc. up to max. 12h) from the start of

HALF LOAD

button and within 4 seconds close the door: the timer

repeatedly until the selected delayed start indicator light

switches off and the wash cycle begins.

appears on the display; each time you press the button,

switches off and the wash cycle begins.

Average

switches off and the wash cycle begins.

ENGLISH

Aby ustawić funkcję połowy załadunku

the selected wash cycle will be increased.

will begin counting down.

If there are not many dishes to be washed, a half load

The start time of the program may be delayed for a period

To adjust the delay time and select a shorter period of time,

the time (1h, 2h, etc. up to max. 12h) from the start of

To adjust the delay time and select a shorter period of time,

«h» switches off.

To adjust the delay time and select a shorter period of time,

Level

Hard

2. Select the wash program, press the START/PAUSE

cycle may be used in order to save water, electricity and

3. Once this time has elapsed, the indicator light «h»

of time between 1 and 12 hours.

press the DELAY button. To cancel it, press the button

the selected wash cycle will be increased.

press the DELAY button. To cancel it, press the button

The DELAY function cannot be set once a wash cycle

DELAY

detergent. Select the program and press the HALF LOAD

button and within 4 seconds close the door: the timer

switches off and the wash cycle begins.

repeatedly until the selected delayed start indicator light

2. Select the wash program, press the START/PAUSE

Very hard

ENGLISH

repeatedly until the selected delayed start indicator light

Soft

repeatedly until the selected delayed start indicator light

1. Press the DELAY button: the corresponding «h» symbol

repeatedly until the selected delayed start indicator light

TABLET (Tab)

Aby ustawić funkcję Multi Tab [dostosow.

button: the indicator light will light up. Press the HALF

has been started.

will begin counting down.

To adjust the delay time and select a shorter period of time,

«h» switches off.

button and within 4 seconds close the door: the timer

«h» switches off.

appears on the display; each time you press the button,

«h» switches off.

LOAD button to deselect this option.

Medium

3. Once this time has elapsed, the indicator light «h»

programu do aktual. użytych detergentów]

3. Once this time has elapsed, the indicator light «h»

This setting allows you to optimize the performance of

press the DELAY button. To cancel it, press the button

• Switch off the appliance by pressing the ON/OFF button.

The DELAY function cannot be set once a wash cycle

will begin counting down.

The DELAY function cannot be set once a wash cycle

DELAY

The DELAY function cannot be set once a wash cycle

the time (1h, 2h, etc. up to max. 12h) from the start of

The DELAY function cannot be set once a wash cycle

Remember to halve the amount of detergent.

Very hard

switches off and the wash cycle begins.

the program according to the type of detergent used.

ENGLISH

repeatedly until the selected delayed start indicator light

has been started.

Setting is complete!

has been started.

3. Once this time has elapsed, the indicator light «h»

Average

has been started.

the selected wash cycle will be increased.

The start time of the program may be delayed for a period

To adjust the delay time and select a shorter period of time,

Press the START/PAUSE button for 3 seconds (the

«h» switches off.

Tabela programów

switches off and the wash cycle begins.

of time between 1 and 12 hours.

2. Select the wash program, press the START/PAUSE

• Switch off the appliance by pressing the ON/OFF button.

Hard

press the DELAY button. To cancel it, press the button

corresponding symbol will light up) if you use combined

The DELAY function cannot be set once a wash cycle

DELAY

To adjust the delay time and select a shorter period of time,

1. Press the DELAY button: the corresponding «h» symbol

FILLING THE RINSE AID DISPENSER

button and within 4 seconds close the door: the timer

Setting is complete!

repeatedly until the selected delayed start indicator light

detergents in tablet form (rinse aid, salt and detergent in

has been started.

Very hard

has been started.

press the DELAY button. To cancel it, press the button

will begin counting down.

Rinse aid makes dish DRYING easier. The rinse aid dispenser A

«h» switches off.

1 dose).

repeatedly until the selected delayed start indicator light

3. Once this time has elapsed, the indicator light «h»

FILLING THE RINSE AID DISPENSER

should be filled when the RINSE AID REFILL indicator light

The DELAY function cannot be set once a wash cycle

If you use powder or liquid detergent, this option

• Switch off the appliance by pressing the ON/OFF button.

DELAY

«h» switches off.

switches off and the wash cycle begins.

2. Select the wash program, press the START/PAUSE

Program

in the control panel is lit.

has been started.

should be off.

Setting is complete!

The start time of the program may be delayed for a period

Rinse aid makes dish DRYING easier. The rinse aid dispenser A

The DELAY function cannot be set once a wash cycle

Program

To adjust the delay time and select a shorter period of time,

Program

of time between 1 and 12 hours.

should be filled when the RINSE AID REFILL indicator light

has been started.

press the DELAY button. To cancel it, press the button

1. Press the DELAY button: the corresponding «h» symbol

3. Once this time has elapsed, the indicator light «h»

FILLING THE RINSE AID DISPENSER

in the control panel is lit.

repeatedly until the selected delayed start indicator light

Program

«h» switches off.

Rinse aid makes dish DRYING easier. The rinse aid dispenser A

To adjust the delay time and select a shorter period of time,

Eco

1 Eco

press the DELAY button. To cancel it, press the button

The DELAY function cannot be set once a wash cycle

should be filled when the RINSE AID REFILL indicator light

2. Select the wash program, press the START/PAUSE

repeatedly until the selected delayed start indicator light

has been started.

in the control panel is lit.

«h» switches off.

Program

Conventional

2 Konwencjonalne

Conventional

To adjust the delay time and select a shorter period of time,

The DELAY function cannot be set once a wash cycle

Eco

Conventional

wash and dry

Program

wash and dry

3. Once this time has elapsed, the indicator light «h»

zmywanie i suszenie

wash and dry

has been started.

press the DELAY button. To cancel it, press the button

wash and dry

repeatedly until the selected delayed start indicator light

To adjust the delay time and select a shorter period of time,

Conventional

«h» switches off.

Intensive

Eco

3 Intensywny

Intensive

press the DELAY button. To cancel it, press the button

1. Open the dispenser B by pressing and pulling up the tab on

The DELAY function cannot be set once a wash cycle

wash and dry

repeatedly until the selected delayed start indicator light

Eco

has been started.

Intensive

the lid.

«h» switches off.

Program

1. Go to the Dishwasher software menu pressing and holding

Conventional

2. Carefully introduce the rinse aid as far as the maximum

The DELAY function cannot be set once a wash cycle

Fast

Intensive

1. Open the dispenser B by pressing and pulling up the tab on

Intensive

4 Szybkie mycie

Fast

button (6 sec).

wash and dry

has been started.

(110 ml) reference notch of the filling space - avoid spilling it.

Conventional

the lid.

2. You switched to NaturalDry Control Menu, you could change

If this happens, clean the spill immediately with a dry cloth.

wash and dry

Fast

2. Carefully introduce the rinse aid as far as the maximum

status of NaturalDry functionality by pressing

Sanitizing

Fast

Eco

Fast

5 Dezynfekcja

3. Press the lid down until you hear a click to close it.

Sanitizing

Intensive

Sanitizing

(110 ml) reference notch of the filling space - avoid spilling it.

– enabled

– disabled

1. Open the dispenser B by pressing and pulling up the tab on

NEVER pour the rinse aid directly into the tub.

If this happens, clean the spill immediately with a dry cloth.

Intensive

To confirm the change and exit from the Control Menu please

the lid.

Conventional

3. Press the lid down until you hear a click to close it.

press and hold

button (3 sec).

Pre-Wash

Sanitizing

Pre-Wash

2. Carefully introduce the rinse aid as far as the maximum

6 Mycie wstępne

Pre-Wash

Fast

Pre-Wash

NEVER pour the rinse aid directly into the tub.

wash and dry

(110 ml) reference notch of the filling space - avoid spilling it.

Fast

If this happens, clean the spill immediately with a dry cloth.

Self-Clean

Pre-Wash

Self-Clean

Sanitizing

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.

7 Samooczyszczanie

Self-Clean

Intensive

Self-Clean

3. Press the lid down until you hear a click to close it.

Pre-Wash

Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following

NEVER pour the rinse aid directly into the tub.

Sanitizing

address: dw_test_support@whirlpool.com

Dane Programu Eco uzyskano na podstawie pomiarów wykonanych w warunkach laboratoryjnych zgodnie z normą europejską EN 60436:2019.

Self-Clean

Pre-treatment of the dishes is not needed before any of the programs.

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.

Pre-Wash

Fast

Uwaga dla laboratoriów testowych: Aby uzyskać informacje na temat warunków badań porównawczych zgodnie z normą EN, prosimy wysłać

*) Not all options can be used simultaneously.

Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.

Pre-Wash

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.

Self-Clean

address: dw_test_support@whirlpool.com

**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many

e-mail na poniższy adres: dw_test_support@whirlpool.com

Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following

factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of

Pre-treatment of the dishes is not needed before any of the programs.

Self-Clean

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.

Sanitizing

Przed żadnym z tych programów nie ma potrzeby wstępnego przygotowania naczyń.

address: dw_test_support@whirlpool.com

load, load balancing, additional selected options and sensor calibration.

*) Not all options can be used simultaneously.

address: dw_test_support@whirlpool.com

Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.

Self-Clean

*) Nie wszystkie opcje mogą być używane jednocześnie.

**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many

Pre-treatment of the dishes is not needed before any of the programs.

Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W

Pre-treatment of the dishes is not needed before any of the programs.

address: dw_test_support@whirlpool.com

Pre-treatment of the dishes is not needed before any of the programs.

factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of

Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following

**) Wartości podane dla programów innych niż program eco są jedynie wartościami referencyjnymi. Rzeczywisty czas może się zmieniać w

Pre-treatment of the dishes is not needed before any of the programs.

*) Not all options can be used simultaneously.

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.

*) Not all options can be used simultaneously.

Pre-Wash

*) Not all options can be used simultaneously.

load, load balancing, additional selected options and sensor calibration.

address: dw_test_support@whirlpool.com

PROGRAMS DESCRIPTION

*) Not all options can be used simultaneously.

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.

zależności od wielu czynników, takich jak temperatura i ciśnienie dopływającej wody, temperatura otoczenia, ilość detergentu, wielkość i typ

Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following

**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.

Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W

**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many

Pre-treatment of the dishes is not needed before any of the programs.

address: dw_test_support@whirlpool.com

factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of

załadunku oraz jego wyważenie, a także od dodatkowo wybranych opcji i kalibracji czujnika.

factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of

Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following

factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of

Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.

Pre-treatment of the dishes is not needed before any of the programs.

*) Not all options can be used simultaneously.

Self-Clean

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.

load, load balancing, additional selected options and sensor calibration.

PROGRAMS DESCRIPTION

load, load balancing, additional selected options and sensor calibration.

1. ECO - program Eco służy do zmywania przeciętnie zabrudzonych naczyń, co oznacza, że do tego zastosowania jest to najbardziej

address: dw_test_support@whirlpool.com

load, load balancing, additional selected options and sensor calibration.

address: dw_test_support@whirlpool.com

load, load balancing, additional selected options and sensor calibration.

address: dw_test_support@whirlpool.com

*) Not all options can be used simultaneously.

Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following

**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many

Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W

**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many

ekonomiczny program pod kątem zużycia wody i energii, oraz że został on użyty do oceny zgodności z przepisami UE w zakresie Ekoprojektu.

Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W

address: dw_test_support@whirlpool.com

Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W

Pre-treatment of the dishes is not needed before any of the programs.

Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W

address: dw_test_support@whirlpool.com

factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of

Pre-treatment of the dishes is not needed before any of the programs.

factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of

Pre-treatment of the dishes is not needed before any of the programs.

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.

2. CONVENTIONAL WASH AND DRY [KONWENCJONALE ZMYWANIE I SUSZENIE] - różny stopień zabrudzenia. Do mycia normalnie

*) Not all options can be used simultaneously.

Pre-treatment of the dishes is not needed before any of the programs.

load, load balancing, additional selected options and sensor calibration.

PROGRAMS DESCRIPTION

load, load balancing, additional selected options and sensor calibration.

*) Not all options can be used simultaneously.

PROGRAMS DESCRIPTION

Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following

PROGRAMS DESCRIPTION

**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many

zabrudzonych naczyń z zaschniętymi resztkami potraw.

PROGRAMS DESCRIPTION

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.

*) Not all options can be used simultaneously.

Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W

**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many

Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W

address: dw_test_support@whirlpool.com

**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many

factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of

3. INTENSIVE - program zalecany w przypadku silnie zabrudzonych naczyń, szczególnie odpowiedni do patelni i garnków (nie należy stosować

**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many

factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of

Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following

Pre-treatment of the dishes is not needed before any of the programs.

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.

PROGRAMS DESCRIPTION

load, load balancing, additional selected options and sensor calibration.

factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of

address: dw_test_support@whirlpool.com

factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of

do delikatnych naczyń).

*) Not all options can be used simultaneously.

Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following

PROGRAMS DESCRIPTION

Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W

**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many

Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W

address: dw_test_support@whirlpool.com

load, load balancing, additional selected options and sensor calibration.

Pre-treatment of the dishes is not needed before any of the programs.

load, load balancing, additional selected options and sensor calibration.

factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of

Pre-treatment of the dishes is not needed before any of the programs.

*) Not all options can be used simultaneously.

Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W

PROGRAMS DESCRIPTION

load, load balancing, additional selected options and sensor calibration.

*) Not all options can be used simultaneously.

Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W

**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many

PROGRAMS DESCRIPTION

**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many

Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W

dishwasher, reduce the amount of detergent used accordingly.

MODIFYING A RUNNING PROGRAM

If a wrong program was selected, it is possible to change it, pro-

vided that it has only just begun: open the door, press and hold

the ON/OFF button, the machine will switch off.

Switch the machine back on using the ON/OFF button and select

the new wash cycle and any desired options; Start the wash cycle

button.

by pressing START/Pause button and closing the door within 4 sec.

ADDING EXTRA CROCKERY

Without switching off the machine, open the door (START/Pause

led starts blinking) (be ware of HOT steam!) and place the

crockery inside the dishwasher. Press the START/Pause button

and close the door within 4 sec., the cycle will resume from the

point at which it was interrupted.

ACCIDENTAL INTERRUPTIONS

If the door is opened during the wash cycle, or if there is a power

cut, the cycle stops. Press the START/Pause button and close

the door within 4 sec., the cycle will resume from the point at

which it was interrupted.

for 5 seconds, until you hear a beep.

(3 sek.).

for 5 seconds, until you hear a beep.

to select the desired hardness level (see

°dH

°fH

The start time of the program may be delayed for a period

of time between 1 and 12 hours.

Water Hardness Table

German degrees

French degrees

to select the desired hardness level (see

1. Press the DELAY button: the corresponding «h» symbol

0 - 6

0 - 10

°dH

The start time of the program may be delayed for a period

appears on the display; each time you press the button,

German degrees

of time between 1 and 12 hours.

the time (1h, 2h, etc. up to max. 12h) from the start of

7 - 11

11 - 20

the selected wash cycle will be increased.

Water Hardness Table

1. Press the DELAY button: the corresponding «h» symbol

Soft

0 - 6

12 - 17

21 - 30

2. Select the wash program, press the START/PAUSE

appears on the display; each time you press the button,

rapidly 3 times

The start time of the program may be delayed for a period

°dH

Medium

button and within 4 seconds close the door: the timer

7 - 11

the time (1h, 2h, etc. up to max. 12h) from the start of

of time between 1 and 12 hours.

18 - 34

31 - 60

will begin counting down.

German degrees

French degrees

the selected wash cycle will be increased.

1. Press the DELAY button: the corresponding «h» symbol

Average

12 - 17

3. Once this time has elapsed, the indicator light «h»

2. Select the wash program, press the START/PAUSE

35 - 50

61 - 90

0 - 6

appears on the display; each time you press the button,

The start time of the program may be delayed for a period

switches off and the wash cycle begins.

button and within 4 seconds close the door: the timer

Hard

18 - 34

the time (1h, 2h, etc. up to max. 12h) from the start of

of time between 1 and 12 hours.

To adjust the delay time and select a shorter period of time,

will begin counting down.

7 - 11

the selected wash cycle will be increased.

press the DELAY button. To cancel it, press the button

1. Press the DELAY button: the corresponding «h» symbol

3. Once this time has elapsed, the indicator light «h»

35 - 50

2. Select the wash program, press the START/PAUSE

repeatedly until the selected delayed start indicator light

12 - 17

switches off and the wash cycle begins.

appears on the display; each time you press the button,

button and within 4 seconds close the door: the timer

«h» switches off.

To adjust the delay time and select a shorter period of time,

the time (1h, 2h, etc. up to max. 12h) from the start of

will begin counting down.

18 - 34

The DELAY function cannot be set once a wash cycle

press the DELAY button. To cancel it, press the button

the selected wash cycle will be increased.

3. Once this time has elapsed, the indicator light «h»

has been started.

2. Select the wash program, press the START/PAUSE

repeatedly until the selected delayed start indicator light

35 - 50

appears on the display; each time you press the button,

switches off and the wash cycle begins.

The start time of the program may be delayed for a period

«h» switches off.

button and within 4 seconds close the door: the timer

the time (1h, 2h, etc. up to max. 12h) from the start of

of time between 1 and 12 hours.

To adjust the delay time and select a shorter period of time,

The DELAY function cannot be set once a wash cycle

will begin counting down.

Faza

Suszenie

press the DELAY button. To cancel it, press the button

the selected wash cycle will be increased.

has been started.

1. Press the DELAY button: the corresponding «h» symbol

3. Once this time has elapsed, the indicator light «h»

repeatedly until the selected delayed start indicator light

susze-

konwen-

appears on the display; each time you press the button,

switches off and the wash cycle begins.

«h» switches off.

button and within 4 seconds close the door: the timer

Program

the time (1h, 2h, etc. up to max. 12h) from the start of

To adjust the delay time and select a shorter period of time,

nia

cjonalne

The DELAY function cannot be set once a wash cycle

will begin counting down.

Program

press the DELAY button. To cancel it, press the button

the selected wash cycle will be increased.

has been started.

2. Select the wash program, press the START/PAUSE

repeatedly until the selected delayed start indicator light

appears on the display; each time you press the button,

switches off and the wash cycle begins.

«h» switches off.

button and within 4 seconds close the door: the timer

Program

the time (1h, 2h, etc. up to max. 12h) from the start of

The DELAY function cannot be set once a wash cycle

will begin counting down.

50°

Program

50°

the selected wash cycle will be increased.

50°

Eco

50°

has been started.

3. Once this time has elapsed, the indicator light «h»

switches off and the wash cycle begins.

1. Go to the Dishwasher software menu pressing and holding

button and within 4 seconds close the door: the timer

Program

Conventional

To adjust the delay time and select a shorter period of time,

55°

will begin counting down.

55°

50°

Eco

Program

55°

50°

55°

wash and dry

55°

press the DELAY button. To cancel it, press the button

2. You switched to NaturalDry Control Menu, you could change

55°

repeatedly until the selected delayed start indicator light

switches off and the wash cycle begins.

«h» switches off.

Conventional

Intensive

65°

55°

The DELAY function cannot be set once a wash cycle

wash and dry

65°

Program

65°

55°

50°

55°

Eco

65°

50°

65°

To confirm the change and exit from the Control Menu please

has been started.

press and hold

50°

Fast

50°

65°

Intensive

65°

Conventional

55°

50°

wash and dry

Program

50°

65°

Eco

50°

55°

50°

Sanitizing

65°

Fast

50°

55°

Intensive

65°

Conventional

50°

button:

55°

65°

wash and dry

Program

65°

50°

Eco

65°

50°

65°

Pre-Wash

Sanitizing

65°

Fast

50°

65°

Intensive

65°

Conventional

55°

Self-Clean

65°

Program

65°

wash and dry

Pre-Wash

65°

Eco

50°

55°

50°

Sanitizing

65°

Fast

50°

Intensive

65°

Conventional

Self-Clean

65°

55°

65°

wash and dry

65°

Eco

Pre-Wash

65°

50°

Sanitizing

65°

Fast

50°

65°

Intensive

65°

Conventional

Self-Clean

55°

65°

wash and dry

Pre-Wash

50°

Sanitizing

65°

Fast

50°

65°

Intensive

65°

Self-Clean

65°

Pre-Wash

Sanitizing

65°

Fast

50°

65°

Self-Clean

65°

Pre-Wash

Sanitizing

65°

Self-Clean

65°

Pre-Wash

Self-Clean

65°

Pełną wersję można pobrać ze strony www.ikea.com

ADJUSTING THE DOSAGE OF RINSE AID

If you are not completely satisfied with the drying results, you can

adjust the quantity of rinse aid used.

ADJUSTING THE DOSAGE OF RINSE AID

• Switch the dishwasher on using the ON/OFF button.

If you are not completely satisfied with the drying results, you can

• Switch it off using the ON/OFF button.

adjust the quantity of rinse aid used.

• Press button

three times - a beep will be heard.

• Switch the dishwasher on using the ON/OFF button.

ADJUSTING THE DOSAGE OF RINSE AID

• Switch it on using the ON/OFF button.

• Switch it off using the ON/OFF button.

If you are not completely satisfied with the drying results, you can

•

The current selection level number and rinse aid indicator light flash.

• Press button

adjust the quantity of rinse aid used.

Eco 50°

•

Press button

to select the level of rinse aid quantity to be

• Switch it on using the ON/OFF button.

• Switch the dishwasher on using the ON/OFF button.

supplied.

•

The current selection level number and rinse aid indicator light flash.

Konwencjonalne zmywanie i

• Switch it off using the ON/OFF button.

•

Press button

• Press button

suszenie 55°

Setting is complete!

supplied.

• Switch it on using the ON/OFF button.

If the rinse aid level is set to ZERO (ECO), no rinse aid will be

• Switch it off using the ON/OFF button.

Intensywny 65°

•

The current selection level number and rinse aid indicator light flash.

supplied. The LOW RINSE AID indicator light will not be lit if you

Setting is complete!

•

Press button

run out of rinse aid. A maximum of 5 levels can be set according to

Szybkie zmywanie 50°

If the rinse aid level is set to ZERO (ECO), no rinse aid will be

supplied.

the dishwasher model. The factory setting is specific to the model,

supplied. The LOW RINSE AID indicator light will not be lit if you

• Switch it off using the ON/OFF button.

please follow instruction above to check this for your machine.

Dezynfekcja 65°

run out of rinse aid. A maximum of 5 levels can be set according to

Setting is complete!

• If you see bluish streaks on the dishes, set a low number (1-2).

the dishwasher model. The factory setting is specific to the model,

If the rinse aid level is set to ZERO (ECO), no rinse aid will be

Mycie wstępne

• If there are drops of water or limescale marks on the dishes,

please follow instruction above to check this for your machine.

supplied. The LOW RINSE AID indicator light will not be lit if you

set a high number (3-4).

• If you see bluish streaks on the dishes, set a low number (1-2).

run out of rinse aid. A maximum of 5 levels can be set according to

Samoczyszczenie 65°

NaturalDry

• If there are drops of water or limescale marks on the dishes,

the dishwasher model. The factory setting is specific to the model,

set a high number (3-4).

Door opening system NaturalDry is a convection drying system

FILLING THE DETERGENT DISPENSER

please follow instruction above to check this for your machine.

• If you see bluish streaks on the dishes, set a low number (1-2).

which automatically opens the door during/after drying phase to

• If there are drops of water or limescale marks on the dishes,

ensure exceptional drying performance every day. Door opens at

FILLING THE DETERGENT DISPENSER

dishwashers.

set a high number (3-4).

To achieve the best washing and drying results, the combined

the temperature that is safe to your kitchen furniture.

NaturalDry

useof detergent, rinse aid liquid and refined salt is required.

NaturalDry

As additional steam protection, special designed protection foil is

dishwashers.

We recommend using detergents that do not contain phosphates

Door opening system NaturalDry is a convection drying system

FILLING THE DETERGENT DISPENSER

To achieve the best washing and drying results, the combined

Door opening system NaturalDry is a convection drying system

added together with the dishwasher. To see how to mount protec-

or chlorine, as these products are harmful to the environment.

which automatically opens the door during/after drying phase to

useof detergent, rinse aid liquid and refined salt is required.

which automatically opens the door during/after drying phase to

tion foil please refer to (INSTALLATION GUIDE).

NaturalDry

Good washing results also depend on the correct amount of

ensure exceptional drying performance every day. Door opens at

We recommend using detergents that do not contain phosphates

dishwashers.

NaturalDry functionality could be disabled by the user as follows:

Door opening system NaturalDry is a convection drying system

the temperature that is safe to your kitchen furniture.

detergent being used.

the temperature that is safe to your kitchen furniture.

Funkcje można wybierać bezpośrednio, naciskając odpowiedni

the temperature that is safe to your kitchen furniture.

or chlorine, as these products are harmful to the environment.

To achieve the best washing and drying results, the combined

which automatically opens the door during/after drying phase to

As additional steam protection, special designed protection foil is

1. Go to the Dishwasher software menu pressing and holding

As additional steam protection, special designed protection foil is

NaturalDry

As additional steam protection, special designed protection foil is

Exceeding the stated amount does not result in a more effective

przycisk (patrz PANEL STEROWANIA).

Good washing results also depend on the correct amount of

NaturalDry

useof detergent, rinse aid liquid and refined salt is required.

ensure exceptional drying performance every day. Door opens at

added together with the dishwasher. To see how to mount protec-

Door opening system NaturalDry is a convection drying system

button (6 sec).

added together with the dishwasher. To see how to mount protec-

wash and increases environmental pollution.

detergent being used.

°fH

We recommend using detergents that do not contain phosphates

NaturalDry

Door opening system NaturalDry is a convection drying system

the temperature that is safe to your kitchen furniture.

tion foil please refer to (INSTALLATION GUIDE).

which automatically opens the door during/after drying phase to

tion foil please refer to (INSTALLATION GUIDE).

The amount can be adjusted to the soil level. In the case of

2. You switched to NaturalDry Control Menu, you could change

French degrees

Jeśli dana funkcja nie może być używana z wybranym

Exceeding the stated amount does not result in a more effective

which automatically opens the door during/after drying phase to

ensure exceptional drying performance every day. Door opens at

NaturalDry

which automatically opens the door during/after drying phase to

As additional steam protection, special designed protection foil is

or chlorine, as these products are harmful to the environment.

As additional steam protection, special designed protection foil is

NaturalDry functionality could be disabled by the user as follows:

Door opening system NaturalDry is a convection drying system

NaturalDry functionality could be disabled by the user as follows:

normally soiled items, use approximately either 35g (powder

the temperature that is safe to your kitchen furniture.

status of NaturalDry functionality by pressing

wash and increases environmental pollution.

ensure exceptional drying performance every day. Door opens at

0 - 10

ensure exceptional drying performance every day. Door opens at

TABLET (Tab)

added together with the dishwasher. To see how to mount protec-

programem (patrz TABELA PROGRAMÓW); odpowiednia

Door opening system NaturalDry is a convection drying system

Good washing results also depend on the correct amount of

added together with the dishwasher. To see how to mount protec-

1. Go to the Dishwasher software menu pressing and holding

which automatically opens the door during/after drying phase to

1. Go to the Dishwasher software menu pressing and holding

As additional steam protection, special designed protection foil is

detergent) or 35ml (liquid detergent) and additional tea spoon of

which automatically opens the door during/after drying phase to

the temperature that is safe to your kitchen furniture.

The amount can be adjusted to the soil level. In the case of

tion foil please refer to (INSTALLATION GUIDE).

button (6 sec).

detergent being used.

button (6 sec).

– enabled

°fH

This setting allows you to optimize the performance of

button (6 sec).

dioda LED mignie szybko 3 razy i będzie słychać sygnał

ensure exceptional drying performance every day. Door opens at

button (6 sec).

added together with the dishwasher. To see how to mount protec-

11 - 20

button (6 sec).

ensure exceptional drying performance every day. Door opens at

detergent directly inside the tub. If tablets are used, one tablet

NaturalDry

As additional steam protection, special designed protection foil is

NaturalDry functionality could be disabled by the user as follows:

normally soiled items, use approximately either 35g (powder

2. You switched to NaturalDry Control Menu, you could change

the program according to the type of detergent used.

2. You switched to NaturalDry Control Menu, you could change

tion foil please refer to (INSTALLATION GUIDE).

2. You switched to NaturalDry Control Menu, you could change

the temperature that is safe to your kitchen furniture.

NaturalDry

2. You switched to NaturalDry Control Menu, you could change

dźwiękowy. Funkcja nie zostanie aktywowana.

To confirm the change and exit from the Control Menu please

the temperature that is safe to your kitchen furniture.

2. You switched to NaturalDry Control Menu, you could change

Exceeding the stated amount does not result in a more effective

will be enough.

21 - 30

added together with the dishwasher. To see how to mount protec-

NaturalDry functionality could be disabled by the user as follows:

Door opening system NaturalDry is a convection drying system

added together with the dishwasher. To see how to mount protec-

Press the START/PAUSE button for 3 seconds (the

1. Go to the Dishwasher software menu pressing and holding

detergent) or 35ml (liquid detergent) and additional tea spoon of

status of NaturalDry functionality by pressing

As additional steam protection, special designed protection foil is

status of NaturalDry functionality by pressing

As additional steam protection, special designed protection foil is

status of NaturalDry functionality by pressing

wash and increases environmental pollution.

0 - 10

press and hold

Door opening system NaturalDry is a convection drying system

which automatically opens the door during/after drying phase to

1. Go to the Dishwasher software menu pressing and holding

If the crockery is only lightly soiled or if it has been rinsed with

corresponding symbol will light up) if you use combined

tion foil please refer to (INSTALLATION GUIDE).

button (6 sec).

added together with the dishwasher. To see how to mount protec-

button (6 sec).

– enabled

detergent directly inside the tub. If tablets are used, one tablet

– disabled

– enabled

– disabled

31 - 60

– enabled

– disabled

added together with the dishwasher. To see how to mount protec-

– enabled

– disabled

– enabled

– disabled

ensure exceptional drying performance every day. Door opens at

button (6 sec).

The amount can be adjusted to the soil level. In the case of

which automatically opens the door during/after drying phase to

NaturalDry

detergents in tablet form (rinse aid, salt and detergent in

tion foil please refer to (INSTALLATION GUIDE).

water before being placed in the dishwasher, reduce the amount

11 - 20

NaturalDry functionality could be disabled by the user as follows:

2. You switched to NaturalDry Control Menu, you could change

To confirm the change and exit from the Control Menu please

will be enough.

To confirm the change and exit from the Control Menu please

tion foil please refer to (INSTALLATION GUIDE).

the temperature that is safe to your kitchen furniture.

2. You switched to NaturalDry Control Menu, you could change

To confirm the change and exit from the Control Menu please

NaturalDry functionality could be disabled by the user as follows:

normally soiled items, use approximately either 35g (powder

ensure exceptional drying performance every day. Door opens at

61 - 90

1 dose).

Door opening system NaturalDry is a convection drying system

of detergent used accordingly (minimum 25 g/ml) e.g. skip the

1. Go to the Dishwasher software menu pressing and holding

status of NaturalDry functionality by pressing

press and hold

As additional steam protection, special designed protection foil is

status of NaturalDry functionality by pressing

button (3 sec).

press and hold

button (3 sec).

If the crockery is only lightly soiled or if it has been rinsed with

press and hold

button (3 sec).

NaturalDry functionality could be disabled by the user as follows:

21 - 30

press and hold

1. Go to the Dishwasher software menu pressing and holding

press and hold

button (3 sec).

If you use powder or liquid detergent, this option

which automatically opens the door during/after drying phase to

detergent) or 35ml (liquid detergent) and additional tea spoon of

the temperature that is safe to your kitchen furniture.

button (6 sec).

powder/gel putted inside the tub.

added together with the dishwasher. To see how to mount protec-

– enabled

button (6 sec).

– disabled

– enabled

– disabled

button (6 sec).

water before being placed in the dishwasher, reduce the amount

1. Go to the Dishwasher software menu pressing and holding

ensure exceptional drying performance every day. Door opens at

should be off.

NaturalDry

As additional steam protection, special designed protection foil is

detergent directly inside the tub. If tablets are used, one tablet

To confirm the change and exit from the Control Menu please

tion foil please refer to (INSTALLATION GUIDE).

31 - 60

2. You switched to NaturalDry Control Menu, you could change

To confirm the change and exit from the Control Menu please

2. You switched to NaturalDry Control Menu, you could change

To confirm the change and exit from the Control Menu please

the temperature that is safe to your kitchen furniture.

button (6 sec).

of detergent used accordingly (minimum 25 g/ml) e.g. skip the

press and hold

NaturalDry functionality could be disabled by the user as follows:

button (3 sec).

added together with the dishwasher. To see how to mount protec-

Door opening system NaturalDry is a convection drying system

will be enough.

status of NaturalDry functionality by pressing

As additional steam protection, special designed protection foil is

status of NaturalDry functionality by pressing

press and hold

button (3 sec).

61 - 90

2. You switched to NaturalDry Control Menu, you could change

1. Go to the Dishwasher software menu pressing and holding

powder/gel putted inside the tub.

which automatically opens the door during/after drying phase to

– enabled

– disabled

tion foil please refer to (INSTALLATION GUIDE).

If the crockery is only lightly soiled or if it has been rinsed with

Duration of

added together with the dishwasher. To see how to mount protec-

– enabled

– disabled

button (6 sec).

ensure exceptional drying performance every day. Door opens at

status of NaturalDry functionality by pressing

To confirm the change and exit from the Control Menu please

NaturalDry

tion foil please refer to (INSTALLATION GUIDE).

NaturalDry functionality could be disabled by the user as follows:

water before being placed in the dishwasher, reduce the amount

2. You switched to NaturalDry Control Menu, you could change

To confirm the change and exit from the Control Menu please

Dostępne

Duration of

To confirm the change and exit from the Control Menu please

Czas trwania

the temperature that is safe to your kitchen furniture.

Duration of

Available

press and hold

Duration of

button (3 sec).

wash pro-

Duration of

– enabled

– disabled

NaturalDry functionality could be disabled by the user as follows:

Door opening system NaturalDry is a convection drying system

1. Go to the Dishwasher software menu pressing and holding

status of NaturalDry functionality by pressing

As additional steam protection, special designed protection foil is

of detergent used accordingly (minimum 25 g/ml) e.g. skip the

press and hold

button (3 sec).

Available

wash pro-

Available

funkcje (*)

1. Go to the Dishwasher software menu pressing and holding

wash pro-

programu

Available

wash pro-

Available

To confirm the change and exit from the Control Menu please

which automatically opens the door during/after drying phase to

wash pro-

Available

wash pro-

Duration of

– enabled

– disabled

options

button (6 sec).

added together with the dishwasher. To see how to mount protec-

powder/gel putted inside the tub.

button (6 sec).

ensure exceptional drying performance every day. Door opens at

options

NaturalDry

gram

options

press and hold

Available

To confirm the change and exit from the Control Menu please

gram

button (3 sec).

wash pro-

options

gram

zmywania

tion foil please refer to (INSTALLATION GUIDE).

options

gram

2. You switched to NaturalDry Control Menu, you could change

the temperature that is safe to your kitchen furniture.

Duration of

press and hold

button (3 sec).

options

NaturalDry functionality could be disabled by the user as follows:

gram

Door opening system NaturalDry is a convection drying system

(h:min)

**)

(h:min)

(godz.:min)**)

**)

status of NaturalDry functionality by pressing

**)

status of NaturalDry functionality by pressing

As additional steam protection, special designed protection foil is

(h:min)

**)

Available

1. Go to the Dishwasher software menu pressing and holding

Available

wash pro-

Duration of

(h:min)

which automatically opens the door during/after drying phase to

– enabled

– disabled

added together with the dishwasher. To see how to mount protec-

– enabled

– disabled

button (6 sec).

Available

ensure exceptional drying performance every day. Door opens at

wash pro-

options

To confirm the change and exit from the Control Menu please

options

gram

tion foil please refer to (INSTALLATION GUIDE).

2:45

2. You switched to NaturalDry Control Menu, you could change

2:45

To confirm the change and exit from the Control Menu please

2:45

the temperature that is safe to your kitchen furniture.

2:45

Duration of

options

gram

press and hold

button (3 sec).

NaturalDry functionality could be disabled by the user as follows:

(h:min)

**)

status of NaturalDry functionality by pressing

As additional steam protection, special designed protection foil is

press and hold

button (3 sec).

(h:min)

1. Go to the Dishwasher software menu pressing and holding

Available

wash pro-

Duration of

– enabled

– disabled

added together with the dishwasher. To see how to mount protec-

button (6 sec).

Available

wash pro-

To confirm the change and exit from the Control Menu please

button (6 sec).

options

tion foil please refer to (INSTALLATION GUIDE).

options

gram

2:00

Available

wash pro-

2:00

2:45

2:00

2. You switched to NaturalDry Control Menu, you could change

2:00

2:45

2:00

options

press and hold

button (3 sec).

gram

NaturalDry functionality could be disabled by the user as follows:

(h:min)

status of NaturalDry functionality by pressing

**)

options

When measuring out the detergent refer to the mentioned ear-

gram

1. Go to the Dishwasher software menu pressing and holding

(h:min)

status of NaturalDry functionality by pressing

Duration of

– enabled

– disabled

2:30

lier information to add the proper quantity. Inside the dispenser

button (6 sec).

(h:min)

– enabled

– disabled

**)

Available

wash pro-

2:00

To confirm the change and exit from the Control Menu please

2:30

2:00

2:45

2. You switched to NaturalDry Control Menu, you could change

2:30

2:45

2:30

B there are indications to help the detergent dosing.

Duration of

options

press and hold

button (3 sec).

gram

When measuring out the detergent refer to the mentioned ear-

status of NaturalDry functionality by pressing

button (3 sec).

Remove detergent residues from the edges of the dispenser