Alarm Relay Priorities - Danfoss AK-CC55 Multi Coil User Manual

AK-CC55 Multi Coil
Function Description
Display readout ad- Correction of the display´s temperature.If the temper-
justment ature at the products and the temperature received
by the controller are not identical, an offset adjust-
ment of the display temperature can be carried out.
Temperature unit Select whether temperatures are to be shown as °C or
as °F.
Display keyboard With this setting it is possible to lock the keyboard
lock operation of the local display.
None: Display keyboard operation will never be
locked
Local: When not used for some time, the local display
will lock the keyboard operations and a special key
combination is required in order to enable the key-
board operations
Network: When the controller receives a master con-
trol signal (--- Key/BT lock) via the network, the dis-
play keyboard operations will be locked. The key-
board operations can only be activated again by set-
ting the master control signal OFF via the System
Manager.

Alarm relay priorities

Table 39: Alarm relay priorities
Function Description
Alarm relay Actual status of output function
Alarm relay priority Set which alarm priorities that are to activate the
alarm relay:
0=Not used. Alarm relay is not used
1=High. Alarm with high priority will activate relay
2=Medium. Alarms with high or medium priority will
activate the alarm relay
3=All. All alarms will activate alarm relay
Mute alarm When muting alarms, the alarm relay will stop signal-
ling the alarm until a new alarm arises
High temperature - Select the priority of the alarms associated to the
Priority alarm group. Be aware - by selecting "Disable" the
alarms will not be shown on the display or be routed
to the alarm relay or to the network.
Low temperature - Select the priority of the alarms associated to the
Priority alarm group. Be aware - by selecting "Disable" the
alarms will not be shown on the display or be routed
to the alarm relay or to the network.
Sensor errors - Prior- Select the priority of the alarms associated to the
ity alarm group. Be aware - by selecting "Disable" the
alarms will not be shown on the display or be routed
to the alarm relay or to the network.
DI alarms - Priority Select the priority of the alarms associated to the
alarm group. Be aware - by selecting "Disable" the
alarms will not be shown on the display or be routed
to the alarm relay or to the network.
Defrost - Priority Select the priority of the alarms associated to the
alarm group. Be aware - by selecting "Disable" the
alarms will not be shown on the display or be routed
to the alarm relay or to the network.
Miscellaneous - Pri- Select the priority of the alarms associated to the
ority alarm group. Be aware - by selecting "Disable" the
alarms will not be shown on the display or be routed
to the alarm relay or to the network.
Injection - Priority Select the priority of the alarms associated to the
alarm group. Be aware - by selecting "Disable" the
alarms will not be shown on the display or be routed
to the alarm relay or to the network.
© Danfoss | Climate Solutions | 2022.08
Values
0=Celsius, 1=Fahrenheit
0=None, 1=Local, 2=Network
Values
0=OFF, 1=ON
0=Not used, 1=High Priority, 2=Medium priority,
3=All
0=OFF, 1=ON
0=Disabled, 3=Low, 2=Medium, 1=High
0=Disabled, 3=Low, 2=Medium, 1=High
0=Disabled, 3=Low, 2=Medium, 1=High
0=Disabled, 3=Low, 2=Medium, 1=High
0=Disabled, 3=Low, 2=Medium, 1=High
0=Disabled, 3=Low, 2=Medium, 1=High
0=Disabled, 3=Low, 2=Medium, 1=High
Code Short name
r04 r04 Disp. Adj. K
r05 r05 Temp.unit
P89 P89 LockDispKey
Code Short name
u62 u62 Alarm relay
P41 P41 Al.Rel.Prio
q38 q38 Mute Alarm
q28 q28 Hi Temp Prio
q29 q29 Lo Temp Prio
q30 q30 Sensor Prio
q31 q31 DIAlarm Prio
q32 q32 Defrost Prio
q33 q33 Misc Prio
q34 q34 Inject Prio
BC365022028193en-000201 | 54