Danfoss AK-CC55 Multi Coil User Manual page 36

AK-CC55 Multi Coil
Function Values
Refrigerant 0=Not seleted, 6=R13, 7=R13b1, 2=R22,
8=R23, 14=R32, 11=R114, 3=R134a,
12=R142b, 24=R170, 15=R227,
25=R290, 16=R401A, 18=R402A,
19=R404A, 21=R407A, 22=R407B,
20=R407C, 37=R407F, 49=R407H,
23=R410A, 32=R413A, 30=R417A,
31=R422A, 33=R422D, 34=R427A,
35=R438A, 40=R448A, 41=R449A,
48=R449B, 43=R450A, 44=R452B,
45=R454B, 9=R500, 4=R502, 10=R503,
17=R507, 36=R513A, 26=R600,
27=R600a, 5=R717, 28=R744,
46=R1233zdE, 38=R1234ze,
39=R1234yf, 47=R1234zeZ, 29=R1270,
42=R452A, 1=User defined display,
13=User defined
DI2 Configuration 0=None, 1=DI status, 2=Door function,
3=Door alarm, 4=Defrost start, 5=Main
switch, 6=Night setback, 7=Thermostat
band, 8=Alarm at closed, 9=Alarm at
open, 10=Case cleaning, 11=Forced
cooling, 13=Coordinated defrost,
14=Forced closing, 15=Shutdown,
16=Light control, 20=Leak detection,
21=Adaptive liquid control, 29=Door
fan stop
Light control mode 1=Day and night, 2=Network, 3=Door
switch, 4=Network (Fallback), 5=Digital
input
MC Light signal 0=OFF, 1=ON
Rail heat ON cycle day
Rail heat ON cycle night
Rail heat period time
Case cleaning mode 0=OFF, 1=Fans run, 2=Cleaning
Application mode 1=1. One evaporator MT/LT, 2=2. Two
evaporators MT/LT, 3=3. Three evapora-
tors MT, 4=4. Coldroom 2 MT/HT, 5=5.
Coldroom 2 MT/LT
Access code 2
Make new factory 0=OFF, 1=ON
DI3 Configuration 0=None, 1=DI status, 2=Door function,
3=Door alarm, 4=Defrost start, 5=Main
switch, 6=Night setback, 7=Thermostat
band, 8=Alarm at closed, 9=Alarm at
open, 10=Case cleaning, 11=Forced
cooling, 13=Coordinated defrost,
14=Forced closing, 15=Shutdown,
16=Light control, 20=Leak detection,
21=Adaptive liquid control, 29=Door
fan stop
Rail heat control mode 0=ON, 1=Day/Night timer, 2=Dewpoint
ctrl.
Dewpoint min. limit
Dewpoint max. limit
Rail heat min. ON cycle
Door restart inj. delay
Fan at forced closing 0=OFF, 1=ON, 2=OFF and suppress de-
frost, 3=ON and suppress defrost
Display readout 1=Ther. air A, 2=Average all, 3=Maxi-
mum all, 4=S4A and S4B
Light at Main switch OFF 0=OFF, 1=Normal ctrl.
(1) (1)
In order to change this parameter the regulation must be stopped via the parameter r12 Main switch = OFF. In order to change this parameter the regulation must be stopped via the parameter r12 Main switch = OFF.
© Danfoss | Climate Solutions | 2022.08
R-W Code 1 2 3
1-3 (1) o30 * * *
1-2 o37 * * *
(1)
1-2 o38 * * *
1-2 o39 * * *
1-2 o41 * * *
1-2 o42 * * *
1-2 o43 * * *
0-1 o46 * * *
1-3 o61 * * *
(1)
2-2 o64 * * *
3-3 o67 * * *
(1)
1-2 (1) o84 * * *
1-2 o85 * * *
1-2 o86 * * *
1-2 o87 * * *
1-2 o88 * * *
1-2 o89 * * *
1-2 o90 * * *
1-2 o97 * * *
1-2 o98 * * *
4 5 Min. value Max. value Fact. value
* * 0 49
* * 0 29
* * 1 5
* * 0 1
* * 0 % 100 %
* * 0 % 100 %
6 min 60 min
* * 0 2
* * 1 5
* * 0 999
* * 0 1
* * 0 29
* * 0 2
* * -10.0 °C o87
* * o86 50.0 °C
* * 0 % 100 %
* * 0 min 240 min
* * 0 3
* * 1 4
* * 0 1
BC365022028193en-000201 | 36
0
0
1
0
100%
100%
6min
0
1
0
0
0
0
8.0 °C
17.0 °C
30%
30 min
1
1
0