Sis Command And Response Table For Advanced Matrix Switcher Commands - Extron electronics XTP II CrossPoint 1600 User Manual

SIS Command and Response Table for Advanced Matrix Switcher Commands

The table that starts below shows commands for advanced operation of the
XTP II CrossPoint matrix switcher frame. Commands shown affect the entire switcher,
regardless of the input boards and output boards installed or any connected endpoints.
Command Function
Black video resolution within the matrix switcher for audio-breakaway ties
Set black signal resolution for the
matrix switcher inputs
Example
(XTP II CrossPoint 3200):
View black signal resolution for the
matrix switcher inputs
Video and audio test patterns
NOTES:
•
The test pattern (J) commands send test patterns to all outputs for setup and calibration. This is separate from the black video signal
insertion into audio breakaway ties (
page 98).
•
The available audio test pattern is a 1-kHz audio tone.
Output test pattern on all outputs
Disable test pattern
View test pattern status
Names
NOTE: The HTML language reserves certain characters for specific functions (see
Write global preset name
Example:
Read global preset name
Example:
Write input name
Example:
Read input name
Write output name
Example:
Read output name
Front panel locks
NOTE: See Setting the Front Panel Locks (Executive Modes)
Lock all front panel functions
Lock advanced front panel functions
Unlock all front panel functions
View lock status
NOTE: X@ = Output number
X# = Global preset number
X^ = Input number (for other than tie)
X1) = Switcher model
X1! = Resolution, rate for black screen
X4# = Test pattern and resolution
X4$ = Name
X4% = Front panel lock
SIS Command Response
(Host to Unit) (Unit to Host)
E X1) X1! }
A * AFMT AfmtA
E }
A33*2AFMT AfmtA33*02
E X1) } X1!]
A AFMT
E
command on page 102
B AFMT
X4#
J Tst
0J Tst00
X4#]
J
,
EX# X4$ }
NG Nmg
E }
1,Security 1NG Nmg01,Security 1
EX# } X4$]
NG
E }
2NG Security 2
,
EX^ X4$ }
NI Nmi
,
E }
1 Podium camNI Nmi01
EX^ } X4$]
NI
,
EX@ X4$ }
NO Nmo
E }
1,Main PJ1NO Nmo01,Main PJ1
EX@ } X4$]
NO
on page 64 for more information on the Lock modes.
1X Exe1
2X
Exe2
0X
Exe0
X4%]
X
– , , or
01 16 32 64
–
01 32
– , , or
01 16 32 64
(XTP II CrossPoint 1600),
17
= 1280x720p @ 50 Hz
2
= Disable ( default )
00
720p, 50 Hz
720p, 60 Hz
1080p. 60 Hz
Up to 12 alphanumeric characters
= Lock mode 0 (unlocked)
0
XTP II CrossPoint 1600, 3200, and 6400 Switchers • Programming Guide
Additional Description
X1) X1!]
Set the black video signal resolution for
*
the matrix switcher.
]
Output a black video signal at 1280x720p
@ 50 Hz when audio is broken away.
E
and the commands on
E AFMT
X4#] Output the selected test pattern.
]
Normal operation, test pattern disabled.
on page 118).
Special Characters
,
X# X4$]
]
Name global preset 1 "Security 1."
]
,
X^ X4$]
, Name input 1 "Podium cam."
]
Podium cam
,
X@ X4$]
]
Name output 1 "Main PJ1."
]
Enable Lock mode 1.
] Enable Lock mode 2.
]
Enable Lock mode 0.
(XTP II CrossPoint 3200), or
33
= 1280x720p @ 60 Hz
4
Color bars Color bars Black screen
No audio Audio No audio
01 07
03 09
05 11
= Lock mode 1
1
page 96 and
(XTP II CrossPoint 6400)
65
= 1920x1080p @ 60 Hz
6
Black screen
Audio
02 08
04 10
06 12
= Lock mode 2 (default)
2
110