Extron electronics XTP II CrossPoint 1600 User Manual page 100

SIS Command and Response Table for Input-Board-Specific Commands (continued)
Command Function
XTP power
ATTENTION:
•
Power over XTP (PoX) is intended for indoors use only. No part of a network that uses PoX can be routed outdoors.
•
PoX est destiné à une utilisation en intérieur uniquement. Aucune partie d'un réseau qui utilise PoX ne peut être routée en extérieur.
NOTE:
•
PoX is supplied by the XTP II CrossPoint 48 V power supply.
•
XTP II CrossPoint 1600:
• Can power up to 28 total (input and output) endpoints at up to 364 watts.
• Is available with optional 48 V power supply redundancy.
•
XTP II CrossPoint 3200:
• Can power up to 24 total (input and output) endpoints at up to 312 watts.
• No 48 V power supply redundancy is available.
•
XTP II CrossPoint 6400:
• Can power up to 128 endpoints at up to 1664 watts.
• 48 V power supply redundancy is standard.
Enable or disable power to input
endpoint and report status
Example:
View input power status
Enable or disable input power and
report status, all inputs
View input power status, all inputs
View XTP power usage
Example:
AES digital audio channel selection
NOTE: Eight-channel audio is divided into two groups, each
consisting of two channel pairs (four channels). The table at
right shows the channels contained within each group.
Select channel
View selected channel
AES digital audio group selection
Select group
View selected group
NOTE: X^ = Input number (for other than tie)
X2# = Enable or disable for power
X2$ = Amount of power requested
X2% = Power status
X2^ = Wattage
X2& = Power supply status
X2* = AESC digital channel pair
X2( = AESG digital channel group
SIS Command Response
(Host to Unit) (Unit to Host)
Inputs on XTP CP 4i [XTP] Boards
E X^ X2# }
I * POEC PoecI
E }
I1*1POEC PoecI01*1*13*1
E X^ } X2#
I POEC
E X2# }
I *POEC PoecI00*
E } X2#
IPOEC
E } X2^
TPOEC
E }
TPOEC 450*0
Inputs on XTP CP 4i 3G Boards
EX^ X2* AESC } Aesc X^
*
X2*]
EX^ AESC }
EX^ X2( AESG } Aesg X^
*
EX^ AESG } X2(]
01 – 16 , 32 , or 64
= Disable (default)
0
or (watts)
00 13
= Unpowered endpoint
0
= Power provided to endpoint
1
Power usage in watt increments. Example: 260 = 26.0 watts
0.1
0 = Ok
(default) or
1 2
(default) or
1 2
XTP II CrossPoint 1600, 3200, and 6400 Switchers • Programming Guide
Additional Description
X^ X2# X2$ X2%]
Enable or disable (
* * *
X^
input
X2$
watts and the power status is
]
Enable remote power on input 1, which
is requesting 13 watts. The board is
providing power to the endpoint.
X2$ X2%]
* *
X2# X2# X2# ] X2#
... Each
1 2 n
an input, starting at 1. n is 16, 32,or 64.
X2# X2# X2# ]
1 2 3 ... n
X2&]
Show PoX wattage applied and the
*
status of the 48 V power supply.
]
The switcher is providing 45.0 watts
and the power supply is Ok.
Group 1
Ch Pair 1 Ch Pair 2 Ch Pair 1
Ch 1 Ch 2 Ch 1 Ch 2 Ch 1 Ch 2 Ch 1 Ch 2
X2*]
Select digital audio channel pair on
*
which audio will be embedded.
X2(] Select digital audio channel group on
*
which audio will be embedded.
= Enable
1
= Power available, disabled
2
= No power available, enabled
3
1 = Not Ok
X2#
) remote power to
. The endpoint is requesting
X2%
.
is the enable or disable status of
Group 2
Ch Pair 2
4 = Fault
92