Extron electronics XTP II CrossPoint 1600 User Manual page 104

SIS Command and Response Table for Input-Endpoint-Specific Commands (continued)
Command Function
XTP T HDMI and XTP T HWP 101 transmitter specific commands
Audio routing selections
Input audio selection
Example 1:
Example 2:
View input audio selection
View all input audio selections
Enable black signal for XTP T
endpoint
Disable black signal for XTP T
endpoint
View black signal output status for
XTP T endpoint
Input reports as an HDCP-authorized device
HDCP authorized device on
HDCP authorized device off
View HDCP authorized status
HDCP status
View input HDCP status
View HDCP status of all inputs
Input sync detection
View all input connections
Example
(XTP II CrossPoint 3200):
NOTE: X% = Input signal status
X^ = Input number (for other than tie)
X1@ = Input audio source
X1# = HDCP authorized device
X1$ = HDCP status (for inputs)
X2#
= Enable or disable
(for black video ties)
SIS Command Response
(Host to Unit to Endpoint) (Endpoint to Unit to Host)
E X^ X1@ }
I * AFMT AfmtI
E }
I1*1AFMT AfmtI01*1
E }
I1*0AFMT AfmtI01*0
E X^ } X1@]
I AFMT
E } X1@
IAFMT
E X^ }
E *1AFMT AfmtE
E X^ }
E *0AFMT AfmtE
E X^ } X2#]
E *AFMT
E X^ }
E *1HDCP HdcpE
E X^ }
E *0HDCP HdcpE
E X^ } X1#]
E HDCP
E X^ } X1$]
I HDCP
E } X1$
I*HDCP
X%
0LS
0LS
Response Status:
0 = No signal detected
– , , or
01 16 32 64
= Auto (see the example above)
0
= HDMI (de-embedded digital audio) (default)
1
= off
0
= No source device connected
0
= Source connected is HDCP-compliant
1
2 = Source connected is not HDCP-compliant
0
= Disable
XTP II CrossPoint 1600, 3200, and 6400 Switchers • Programming Guide
Additional Description
X^ X1@]
* Use audio from the
]
Use digital audio from the HDMI port of
input 1.
]
Auto (0): Digital audio takes priority over
analog audio.
X1@ X1@ X1@ ]
16, 32, or 64 (
...
1 2 3 n
selections, starting from input 1.
X^ ]
Enable an audio only tie for the
*1
connected XTP transmitter.
X^ ]
Disable an audio only tie for the
*0
connected XTP transmitter.
The black signal status of XTP
transmitter endpoint
X^ ]
Set the input as an HDCP authorized
*1
device.
X^ ]
Set the input as not an HDCP
*0
authorized device.
Show HDCP authorized device status.
X1$ X1$ X1$ ]
...
1 2 3 n
X% X% X% ]
16, 32, or 64 (
...
1 2 3 n
connection status of an input, starting
from input 1.
Sync detected
No input detected
0 0 0 1 1 1 0 1 0 0 1 0 1. . .0
Input: 1 2 3 4 5 6 7 8 9 10111213
1 = Signal detected
= Analog 2-channel audio
2
= on (default)
1
= Enable (default)
1
X1@
source.
) sequential audio input
n
X^ X2#
is .
X%
) s; each is the
n
Sync detected
32
96