Extron electronics XTP II CrossPoint 1600 User Manual page 98

SIS Command and Response Table for Input-Board-Specific Commands (continued)
Command Function
Input sync detection
View all input connections
Example
(XTP II CrossPoint 3200):
Inputs on XTP CP 4i HDMI, XTP CP 4i HD 4K PLUS, XTP CP 4i DVI Pro, XTP CP 4i 3G,
Audio input gain and attenuation
NOTE: The set gain ( G ) and set attenuation (
Set audio input gain to +dB value
Example:
Set audio input attenuation to -dB
value
Increment gain
Example:
Decrement gain
Example:
Read input gain
Example:
Inputs on XTP CP 4i HDMI, XTP CP 4i HD 4K PLUS, XTP CP 4i DVI Pro, and XTP CP 4i 3G Boards
Audio routing selections
NOTE: These commands select between the audio embedded in the digital video stream and the 2-channel analog audio.
Input audio selection
Example 1:
Example 2:
View input audio selection
View all input audio selections
Inputs on XTP CP 4i HDMI, XTP CP 4i HD 4K PLUS, and XTP CP 4i DVI Pro Boards
Input reports as an HDCP-authorized device
HDCP authorized device on
HDCP authorized device off
View HDCP authorized status
NOTE: X% = Input signal status
X^ = Input number (for other than tie)
X& = Audio gain
X* = Numeric dB value
X( = Audio attenuation
X1! = Resolution and rate for black screen
X1@ = Input audio source
X1# = HDCP authorized device
SIS Command Response
(Host to Unit) (Unit to Host)
X%
0LS
0LS
Response Status:
XTP CP 4i VGA Boards
g ) commands are case sensitive.
X^ X&
* G In
1*2G
In01•Aud+02
X^ X(
* g In
X^
+G In
5+G
In05•Aud+03
X^
–G In
7–G
In07•Aud-09
X^ X*]
G
3G
-06
E X^ X1@ }
I * AFMT AfmtI
E }
I1*1AFMT AfmtI01*1
E }
I1*0AFMT AfmtI01*0
E X^ } X1@]
I AFMT
E } X1@
IAFMT
E X^ }
E *1HDCP HdcpE
E X^ }
E *0HDCP HdcpE
E X^ } X1#]
E HDCP
= No signal detected
0
– , , or
01 16 32 64
– (1 dB per step)
0 24
to (43 steps of gain or attenuation) (0 dB = default)
–18 +24
1 – 18 (1 dB per step)
= 1280x720p @50 Hz
2
= Auto (see the example above)
0
= HDMI (de-embedded digital audio) (default)
1
= Analog 2-channel audio
2
= off
0
XTP II CrossPoint 1600, 3200, and 6400 Switchers • Programming Guide
Additional Description
X% X% X% ]
... 16, 32, or 64 (
1 2 3 n
connection status of an input, starting
from input 1.
Sync detected
No input detected
0 0 0 1 1 1 0 1 0 0 1 0 1. . .0
Input: 1 2 3 4 5 6 7 8 9 10111213
X^ X*]
•Aud
]
Set input 1 audio gain to +2 dB.
X^ X*]
•Aud
X^ X*]
Increase gain by 1 dB.
•Aud
]
Increase audio input 5 level from +2 dB
to +3 dB.
X^ X*]
Decrease gain by 1 dB.
•Aud
]
Decrease audio input 7 level from -8 dB
to -9 dB.
]
Audio input 3 level is at -6 dB.
X^ X1@]
Use audio from the
*
]
Use analog audio from the analog audio
port of input 1.
]
Auto (0): Digital audio takes priority over
analog audio.
X1@ X1@ X1@ ]
16, 32, or 64 (
1 2 3 ...
n
selections, starting from input 1.
X^ ]
Set the input as an HDCP authorized
*1
device.
X^ ]
Set the input as not an HDCP
*0
authorized device.
Show HDCP authorized device status.
= Sync detected
1
= 1280x720p @60 Hz
4
= on (default)
1
X%
n ) s; each is the
Sync detected
32
X1@
source.
) sequential audio input
n
= 1920x1080p @60 Hz
6
90