Sis Command And Response Table For Output-Board-Specific Commands - Extron electronics XTP II CrossPoint 1600 User Manual

SIS Command and Response Table for Output-Board-Specific Commands

The table that starts below shows commands that affect outputs only and, in general, apply
to installed output boards. Where a command does not apply to all output board types, the
valid board types are noted.
Command Function
Outputs on XTP CP 4o HDMI, XTP II CP HD 4K PLUS, and XTP CP 4o DVI Pro Boards
Audio routing selections
NOTE: These commands select between the audio embedded in the digital video stream and the 2-channel analog audio.
Output audio HDMI select
Example:
View output audio breakaway
selection
View output audio breakaway
selection, all outputs
Enable black signal output for audio
only tie
Disable black signal output for audio
only tie
View black signal output status
Enable black signal for all audio
only ties
Disable black signal for all audio
only ties
HDCP status
View output HDCP status
View HDCP status of all outputs
Video mutes
Video mute
Video unmute
Read video mute
Global video mute
Global video unmute
X@ = Output number
NOTE:
X2# = Enable, disable (for black video and mutes, see above)
X3% = Output audio source
X3^ = HDCP status (for outputs)
SIS Command Response
(Host to Unit) (Unit to Host)
E X@ X3% }
O * AFMT AfmtO
E }
O3*0AFMT AfmtO03*0
E X@ } X3%]
O AFMT
E } X3%
OAFMT
E X@ }
B *1AFMT AfmtB
E X@ }
B *0AFMT AfmtB
E X@ } X2#]
B AFMT
E }
B1*AFMT AfmtB1
E }
B0*AFMT AfmtB0
E X@ } X3^]
O HDCP
E } X3^
O*HDCP
X@
*1B Vmt
X@
*0B Vmt
X@ X2#]
B
1*B
Vmt1
0*B
Vmt0
01
0
0
0
1
7
XTP II CrossPoint 1600, 3200, and 6400 Switchers • Programming Guide
Additional Description
X@ X3%] When audio is broken away from video,
*
embed audio from the
video output.
]
When audio is broken away from video,
use the embedded audio from the input
port when creating an audio breakaway
tie to output 3.
X3% X3% X3% ]
16, 32, or 64 (
...
1 2 3 n
selections, starting from output 1.
X@ ]
Enable black signal in audio only tie to
*1
output
X@ ]
Disable black signal in audio only tie to
*0
output
The black signal status of output
]
Enable black signal in audio only tie to
all outputs.
]
Disable black signal in audio only tie to
all outputs.
X3^ X3^ X3^ ]
...
1 2 3 n
X@ ]
Mute output
*1
X@ ]
Unmute output
*0
X2#
=
1
0
]
Mute all video outputs.
]
Unmute all video outputs.
– , , or
16 32 64
= Disable
= Original HDMI audio
, , , or = No monitor connected
2 4 6
, 3 , or 5 = Monitor connected but the video signal is not encrypted
= Monitor connected and the video signal is encrypted
X3%
source in the
) sequential audio output
n
X@
.
X@
.
X@ X2#
is .
X@
video (video off).
X@
video (video on).
= enable (muted)
= disable (unmuted) (default).
= Enable
1
= Embed audio
1
102