Sis Command And Response Table For Output-Endpoint-Specific Commands - Extron electronics XTP II CrossPoint 1600 User Manual

SIS Command and Response Table for Output-Endpoint-Specific Commands

The table that starts below shows commands that affect XTP R HDMI receiver,
XTP R HWP 201 receiver, and XTP SR HDMI scaler endpoints connected through an XTP
board only. The XTP II CrossPoint switcher acts as a master, forwarding the commands to
the endpoint slave.
Command Function
XTP R HDMI, XTP R HWP 101 receiver specific commands
Video mutes
Video mute
Video unmute
Read video mute
Global video mute
Global video unmute
Audio routing selections
NOTES:
•
These commands select between the audio embedded in the digital video stream and the 2-channel analog audio.
•
These commands are valid only if audio breakaway switching is performed (see the
Output audio HDMI select
Example:
View output audio breakaway
selection
View output audio breakaway
selection, all outputs
Audio output volume
Set the audio volume to a specific
value
Example:
Increment volume
Example:
Decrement volume
Read output volume
Audio mutes
Mute digital audio
Mute analog audio
Mute digital and analog audio
Unmute both audio
View audio mute status
Global digital audio mute
Global analog audio mute
Global digital and analog audio mute
Global audio unmute
:
X@
NOTE = Output number
X2# = Enable and disable for mutes
X3% = Output audio source
X3& = Volume
X3* = Digital and analog audio mute status
SIS Command Response
(Host to Unit to Endpoint) (Endpoint to Unit to Host)
X@
*1B Vmt
X@
*0B Vmt
X@ X2#]
B
1*B Vmt1
0*B
Vmt0
E X@ X3% }
O * AFMT AfmtO
E }
O3*0AFMT AfmtO03*0
E X@ } X3%]
O AFMT
E } X3%
OAFMT
X@ X3&
* V Out
1*50v
Out01•Vol50
X@
+V Out
1+V
Out01•Vol51
X@
-V Out
X@ X3&]
V
X@
*1Z Amt
X@
*2Z Amt
X@
*3Z Amt
X@
*0Z Amt
X@ X3*]
Z
1*Z Amt1
2*Z
Amt2
3*Z Amt3
0*Z
Amt0
01 – 16 , 32 , or 64
= Disable
0
= Original HDMI audio
0
– (1 dB per step except for
00 64
= No mutes
0
= Digital audio mute
1
XTP II CrossPoint 1600, 3200, and 6400 Switchers • Programming Guide
Additional Description
X@ ]
Mute output
*1
X@ ]
Unmute output
*0
X2#
=
1
0
]
Mute all video outputs.
] Unmute all video outputs.
commands on page 86)
Create Ties
X@ X3%]
When audio is broken away from video,
*
embed audio from the
video output.
]
When audio is broken away from video,
use the embedded audio from the input
port when creating an audio breakaway
tie to output 3.
X3% X3% X3% ] 16, 32, or 64 (
...
1 2 3 n
selections, starting from output 1.
X@ X3&]
•Vol
]
Set output 1 volume to 79%.
X@ X3&]
Increment volume by 1 step.
•Vol
]
X@ X3&]
Decrease volume by 1 step.
•Vol
X@ ]
Mute output
*1
X@ ]
Mute output
*2
X@ ]
*3
X@ ]
Unmute output
*0
]
Mute all audio digital outputs.
]
Mute all analog audio outputs.
]
Mute all digital and analog audio outputs.
] Unmute all audio outputs.
= Enable
1
= Embed audio (default)
1
-to- , which is 13 dB) (see
0 1
= Analog audio mute
2
= Analog and digital audio mute
3
X@
video (video off).
X@
video (video on).
= enable (muted)
= disable (unmuted) (default).
X3%
source in the
) sequential audio output
n
X@
digital audio (audio off).
X@
analog audio (audio off).
X@
audio (audio on).
table 10 on page 103)
106