Extron electronics XTP II CrossPoint 1600 User Manual page 106

SIS Command and Response Table for Input-Endpoint-Specific Commands (continued)
Command Function
XTP T USW 103 switcher specific commands (continued)
Audio routing selections
Enable black signal for XTP T
endpoint
Disable black signal for XTP T
endpoint
View black signal output status for
XTP T endpoint
Input reports as an HDCP-authorized device
HDCP authorized device on
HDCP authorized device off
View HDCP authorized status
HDCP status
View input HDCP status
View HDCP status of all inputs
Input sync detection
View all input connections
Example
(XTP II CrossPoint 3200):
Input video format
Set format
Example:
View format
Image reset
Execute an image reset
NOTE: X% = Input signal status
X^ = Input number (for other than tie)
X1# = HDCP authorized device
X1$ = HDCP status (for inputs)
X2#
= Enable or disable
(for black signal output)
X3) = Input video source
X3! = Detected video format
SIS Command Response
(Host to Unit to Endpoint) (Endpoint to Unit to Host)
E X^ }
E *1AFMT AfmtE
E X^ }
E *0AFMT AfmtE
E X^ } X2#]
E *AFMT
E X^ }
E *1HDCP HdcpE
E X^ }
E *0HDCP HdcpE
E X^ } X1#]
E HDCP
E X^ } X1$]
I HDCP
E } X1$
I*HDCP
X%
0LS
0LS
Response Status:
XTP T VGA transmitter specific commands
X^ X3)
* \ Ityp
1*0\
Ityp01*0*5
X^ X3)
\
X^
A Aadj
0 = No signal detected
– , , or
01 16 32 64
= Off
0
= No source device connected
0
= Source connected is HDCP-compliant
1
= Source connected is not HDCP-compliant
2
= Disable
0
= Auto (default)
0
= Video
1
= S-video
2
= RGBcvS (SCART)
3
0 = no signal detected
1 = Video
2 = S-video
3 = RGBcvS (SCART)
XTP II CrossPoint 1600, 3200, and 6400 Switchers • Programming Guide
Additional Description
X^ ]
Enable an audio only tie for the
*1
connected XTP transmitter.
X^ ]
Disable an audio only tie for the
*0
connected XTP transmitter.
The black signal status of XTP
transmitter endpoint
X^ ] Set the input as an HDCP authorized
*1
device.
X^ ]
Set the input as not an HDCP
*0
authorized device.
Show HDCP authorized device status.
X1$ X1$ X1$ ]
...
1 2 3 n
X% X% X% ]
16, 32, or 64 (
...
1 2 3 n
connection status of an input, starting
from input 1.
Sync detected
No input detected
0 0 0 1 1 1 0 1 0 0 1 0 1. . .0
Input: 1 2 3 4 5 6 7 8 9 10111213
X^ X3) X3!]
Set input
* *
board reports the detected video
format,
]
Set input 1 to auto. The board reports
RGB video.
X3!]
View set (
*
format of input
X^]
Reset input signal timing to Extron
default for input
1 = Sync detected
= On (default)
1
= Enable (default)
1
= YUV interlace
4
= RGB
5
= YUV
6
4 = YUV interlace
5 = RGB
6 = YUV
X@ X2#
is .
X%
) s; each is the
n
Sync detected
32
X^ X3)
to video format. The
X3!
, in the response.
X3) X3!
) and detected ( ) video
X^
.
X^
.
98