Advertisement
Brillion Elite Mini Monitor -
Optional
Assembly instruction for models with Clutch.
IMPORTANT
The Brillion Elite Mini Monitor System by Loup
utilizes a MUX communication line. Sensors must be
learned into the Monitor. Location of each pre-learned
Smart Shaft Sensor or Bin Level Sensor is important
for proper Monitor display. Each Sensor utilizes
3 wires (+, -, MuxBus) to connect to the system. The
Harnesses do not require a specific Sensor
connection points. Each Sensor is identified in the
Monitor by its own signal.
WARNING
High Power Magnet in use. See "High Power
Magnet" on page 1-2.
IMPORTANT
All Harnesses must be firmly attached to Machine
Frame members so they do not sag or become torn
loose by field debris.
Refer to Brillion Elite Mini Monitor Single Box Schematic.
See Figure 2-18.
1. Lay out the Seeder Harness on the Seeder Front
Frame Tube ensuring that the Electric Clutch 2-Pin
Connector is on the left side. See Figure 2-17.
2. Rear RH side of the Seeder, has a sensor mounted
on two seed cups. Attach a Smart Shaft Sensor to the
Sensor Mount with sensor provided hardware and
#8-32 Flange Locknuts. Adjust the Smart Shaft
Sensor so that it is 1/8" Max away from the Spacer
w/Magnet on the Seed Shaft. See Figure 2-18.
Connect the Smart Seed Shaft Sensor to the Seeder
Harness.
3. Remove the .803 Knockouts in the front RH and LH
ends of the Seed Box.
4. The Seeder has a Bin Level Sensor Bracket on the
inside at either end. See Figure 2-20. Determine the
desired level for the alarm to be indicated on the Brillion
Elite Mini Monitor and assemble the Bin Level Sensors
to Bin Level Sensor Brackets with sensor provided
hardware and #8-32 Flange Locknuts. If more
adjustment is needed, the Bin Level Sensor Brackets
can also be raised or lowered to the desired seed
level. Install Cord Grips from the inside of the Seed Box
out and secure with supplied Locknut on the outside of
the Seed Box. To get the Sensor Connector outside the
Seed Box, feed the terminals through the Cord Grip.
Install the terminals into the 3-Pin Shroud labeled "A",
"B" and "C" as follows "A" White, "B" Black, "C" Green.
2-18
TABLE OF CONTENTS
See Figure 2-15. Inside the Seed Box, add enough
slack to the Bin Level Sensor Cord to allow for future
adjustments of the Sensor. Secure the Bin Level Cord
by tightening the Cord Grip Compression Nut. Connect
both Bin Level Sensors to the Seeder Harness.
Shroud Pin ID
3-Pin Shroud
Figure 2-15: Bin Level Sensor Wire Detail
5. Pickup Switch Bracket is mounted on the Clutch Shaft
Bearing Carriage Bolts. See Figure 2-21. Assemble
Smart Shaft Sensor onto the Pickup Switch Bracket
with sensor provided hardware and #8-32 Flange
Locknuts. Adjust the Smart Shaft Sensor so that it is
an 1/8" Max away from the Actuator Assembly.
Connect the Ground Speed Smart Shaft Sensor to the
Seeder Harness.
6. Unused Seeder Harness RH 3-Pin Connector needs
to be sealed with a 3-Pin Shroud and Cavity Plugs to
protect the Harness from the environment.
7. Connect the 240" Extensions Harness to the Seeder
Harness. Route the 240" Extension Harness along
the Seeder Frame and down the Drawbar/3-PT Hitch
to the Tractor.
8. Install Brillion Elite Mini Monitor on Tractor. See
"Brillion Elite Mini Monitor Tractor Installation -
Optional" on page 2-25.
9. If not already installed, install Smart Clutch Relay into
Elite Mini Tractor Harness 3-Pin Connectors.
10. Connect the Elite Mini Tractor Harness 14-Pin
Connector to Brillion Elite Mini Monitor, 3-Pin Power
Plug to 12 Volt Tractor Convenience Outlet and 6-Pin
Connector to the 240" Extension Harness. 4-Pin
Connector is not used at this time.
11. Bundle and secure all Harnesses along the Seeder
Frame and Drawbar/3-PT Hitch with Tie Wraps.
12. Program Bin Level Sensors and Smart Shaft Sensors
if not already pre-programmed. See Brillion Elite
Mini Monitor Chapter.
Terminal
White Wire
Black Wire
Seal
Green Wire
F-1021-0422
Advertisement
