Landoll Brillion SSB8 Operator's Manual

Landoll Brillion SSB8 Operator's Manual

Hide thumbs Also See for Brillion SSB8:

Advertisement

Quick Links

Sure Stand Seeder
Models SSB8/SSB10/SSB12
SSBP8/SSBP10/SSBP12
Operator's Manual
LANDOLL COMPANY, LLC
1900 North Street
Marysville, Kansas 66508
(785) 562-5381
800-428-5655 ~ WWW.LANDOLL.COM
1P480-0522

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Brillion SSB8 and is the answer not in the manual?

Questions and answers

Summary of Contents for Landoll Brillion SSB8

  • Page 1 Sure Stand Seeder Models SSB8/SSB10/SSB12 SSBP8/SSBP10/SSBP12 Operator’s Manual LANDOLL COMPANY, LLC 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM 1P480-0522...
  • Page 2 Manuals for Sure Stand Seeder, Models SSB8/SSB10/SSB12 and SSBP8/SSBP10/SSBP12 Manual Number Manual Name 1P480 Operator’s Manual 1P481 Parts Manual...
  • Page 3 Table of Contents Introduction and Safety Information Introduction ..............1-1 Description of Unit .
  • Page 4 Front Seed Box Dividers - Optional ..........2-33 Rear Seed Box Dividers - Optional .
  • Page 5 Settings Menu - Install Setup ........... . 4-5 Learn New System .
  • Page 7 Failure warranty obligation unless each product is registered, to comply with this warning can result in within 10 days of retail purchase, using the Landoll personal injury or death, damage to the machine Company, LLC Ag Products on-line registration process.
  • Page 8 INTRODUCTION AND SAFETY INFORMATION Safety • When applying decals to the machine, be sure to clean the surface to remove any dirt or residue. Where possible, sign placement should protect the sign from NOTE abrasion, damage, or obstruction from mud, dirt, oil etc. Investigation has shown that nearly 1/3 of all farm ...
  • Page 9 INTRODUCTION AND SAFETY INFORMATION Transporting Safety Attaching, Detaching and Storage • Do not stand between the tractor and machine when attaching or detaching machine unless both are not IMPORTANT moving. It is the responsibility of the owner/operator to • Before applying pressure to the hydraulic system, be comply with all state and local laws.
  • Page 10 INTRODUCTION AND SAFETY INFORMATION Tire Safety NOTE Tire changing can be dangerous and should be performed Relieve hydraulic pressure by shifting the control valve by trained personnel using correct tools and equipment. lever to float. • When inflating tires, use a clip-on chuck and extension Wear protective gloves and safety glasses or goggles hose long enough to allow you to stand to one side, when working with hydraulic systems.
  • Page 11 Lower load or relieve hydraulic pressure before loosening fittings. PARKING PIN ITEM 17 - 3K706 ITEM 15 - 9J301 ITEM 10 9J432 Landoll Company, LLC Marysville, Kansas www.landoll.com MODEL # SERIAL # MADE IN USA 1-573-010006 AG SEEDER...
  • Page 12 INTRODUCTION AND SAFETY INFORMATION Figure 1-4: Decals Placement - Hitch 1P480-0522...
  • Page 13 INTRODUCTION AND SAFETY INFORMATION Figure 1-5: Decal Placement - 8FT 1P480-0522...
  • Page 14 INTRODUCTION AND SAFETY INFORMATION Figure 1-6: Decal Placement - 10FT 1P480-0522...
  • Page 15 INTRODUCTION AND SAFETY INFORMATION Figure 1-7: Decal Placement - 12FT 1P480-0522...
  • Page 16 ITEM 9 check for leaks. Lower load or relieve hydraulic ITEM 5 9J302 pressure before loosening fittings. 8J309 ITEM 8 3K706 Landoll Company, LLC Marysville, Kansas www.landoll.com MODEL # PARKING PIN SERIAL # MADE IN USA 1-573-010006 ITEM 6 ITEM 7...
  • Page 17 INTRODUCTION AND SAFETY INFORMATION Figure 1-9: Decal Placement - SD8 Model 1P480-0522 1-11...
  • Page 18 INTRODUCTION AND SAFETY INFORMATION Figure 1-10: Decal Placement - SDP8 Model 1-12 1P480-0522...
  • Page 19 INTRODUCTION AND SAFETY INFORMATION Figure 1-11: Decal Placement - SD10 Model 1P480-0522 1-13...
  • Page 20 INTRODUCTION AND SAFETY INFORMATION Figure 1-12: Decal Placement - SDP10 Model 1-14 1P480-0522...
  • Page 21 INTRODUCTION AND SAFETY INFORMATION Figure 1-13: Decal Placement - SD12 Model 1P480-0522 1-15...
  • Page 22 INTRODUCTION AND SAFETY INFORMATION Figure 1-14: Decal Placement - SDP12 Model 1-16 1P480-0522...
  • Page 23 Chapter 2 Assembly  IMPORTANT CAUTION All harnesses must be firmly attached to machine Do Not Work On Or Under This Machine Unless frame members, so they don’t sag or become torn Securely Blocked And Supported By A Hoist Or loose by field debris.
  • Page 24 ASSEMBLY PT Seeder Assembly  CAUTION When shipped, seeder comes assembled except for Do not disengage pin unless seeder is fully Lights and 3-PT Hitch. attached to a tractor. Seeder may be rear-heavy 1. Support Seeder Assembly with a hoist or by similar and tip backward on frame.
  • Page 25 ASSEMBLY Frame Nut,5/8-11 Lock Washer,5/8 Hose Clamp Manual Holder Op3PtHitch U-Bolt,5/8-11 3-PT Hitch Figure 2-4: Attach 3-PT Hitch 1P480-0522...
  • Page 26 ASSEMBLY Pull Type Seeder Assembly Rear When shipped, Seeder comes assembled except for Seed Box Lights, Hub and Spindle Assemblies, Tire and Wheels Assemblies and Drawbar. 1. Untie the two rolled up Drawbar Hydraulic Hoses near the center of the Frame Tube. Ensure the hoses are not interfering with where the Drawbar is to be attached.
  • Page 27 ASSEMBLY Tire and Wheel Installation  WARNING Use a torque wrench to assure proper torque. Insufficient torque can cause stud breakage and damage the wheel pilots. Over torque can stress the Bolts and strip the threads. NOTE The tire/wheel assembly is mounted with the valve stem facing outward from Hub and Spindle.
  • Page 28 ASSEMBLY Hydraulic Installation Hydraulic Assembly 1. Restrictors installed in Cylinder Ports, connect 45  Degree Fitting so they are free to swivel. Connect top WARNING Hydraulic Hose to the Cylinder Base and bottom Hydraulic Hose to the Cylinder Rod End. Position the Escaping fluid under pressure can be nearly Hydraulic Hoses so that the Cylinder Base End invisible and have enough force to penetrate the...
  • Page 29 ASSEMBLY Hose Clamp Pair Frame Hose Assembly Bolt,1/4-20 x 1-1/2 Top Plate Drawbar Figure 2-11: Drawbar Hydraulic Hoses 1P480-0522...
  • Page 30 ASSEMBLY Purge the Hydraulic Lift System Bolt,5/8-11 Flat Washer,5/8 The Hydraulic system is not filled with oil and should be purged of air before transporting and field operations. Locknut,5/8-11 Lift Circuit approximate oil requirement: 0.4 gallons. 1. Carefully Hitch the Seeder to the Tractor and connect the Hydraulic Lift Hoses.
  • Page 31 ASSEMBLY Table provided for general use. NOTES: 1P480-0522...
  • Page 32 ASSEMBLY Warning Lamp Installation, 8FT Hydraulic Hoses or 3-PT Hitch Frame Slots allowing enough Harness length to reach the Tractor Socket. and 10FT NOTE NOTE If equipped with optional Electrical Clutch, install, route and secure Electric Clutch Harness with the Warning 10FT Drawbar model is shown, 10FT 3-PT, 8FT Drawbar Lamp Harness.
  • Page 33: Table Of Contents

    ASSEMBLY Light Bracket Amber Lamp Locknut,1/4-20 Bolt,1/4-20 Bolt,1/2-13 x 1-1/4 x 1-1/4 Red Lamp Lock Washer,1/2 Angled Light Nut,1/2-13 Bracket Wrap Bolt,5/16-18 x 1 Locknut, Bolt,1/4-20 x 1 5/16-18 Flat Washer,5/16 Connector Holder Mount Locknut, Flat Washer,1/4 1/4-20 Lamp Harness Locknut,1/4-20 7-Pin Harness...
  • Page 34: Locknut

    ASSEMBLY Warning Lamp Installation, 12FT NOTE If equipped with Electrical Clutch, install, route and NOTE secure Electric Clutch Harness with the Warning Lamp 12FT 3-PT model is shown, drawbar model similar. Harness. 1. Place a Red Lamp at each end of the Light Bar and IMPORTANT insert the Red Lamp cord into the Light Bar cutout.
  • Page 35: Red Lamp

    ASSEMBLY Light Bracket Locknut,1/4-20 Bolt,1/4-20 x 1-1/4 Bolt,1/2-13 x 1-1/4 Amber Lamp Angled Light Bracket Lock Washer,1/2 Red Lamp Tie Wrap Bolt,1/4-20 Nut,1/2-13 x 1-1/4 Bolt, Bolt,1/4-20 x 1 5/16-18 x 1 Locknut, Connector 5/16-18 Holder Flat Washer,5/16 Light Bar Locknut, 1/4-20 Flat...
  • Page 36 ASSEMBLY Table provided for general use. NOTES: 2-14 1P480-0522...
  • Page 37 ASSEMBLY Electric Clutch Kit - Optional Mini Monitor, 3-Pin Power Plug to 12 Volt Tractor Convenience Outlet and 6-Pin Connector to the 240" Extension Harness. 4-Pin Connector is not used at IMPORTANT this time. Connect 240" Extension Harness to Seeder At no time use high pressure water or air to clean the Harness.
  • Page 38 ASSEMBLY Brillion Elite Mini Monitor - 1/8" Max away from the Magnet Collar on the Seed Shaft. See Figure 2-24. Connect the Smart Seed Optional Shaft Sensor to the Seeder Harness. Assembly instruction for models with Clutch. Smart Shaft Pick-up Switch IMPORTANT Sensor Bracket...
  • Page 39 ASSEMBLY 6. On the inside at either end of the Seed Box, install a 7. Connect the 240" Extensions Harness to the Seeder Bin Level Sensor Bracket with the Seed Box Harness. Route the 240" Extension Harness along Mounting 3/8-16 Hardware. See Figure 2-29. the Seeder Frame and down the Drawbar/3-PT Hitch Determine the desired level for the alarm to be to the Tractor.
  • Page 40 ASSEMBLY Brillion Elite Mini Monitor Electrical Schematic Figure 2-25: Brillion Elite Mini Monitor Electrical Schematic 2-18 1P480-0522...
  • Page 41 ASSEMBLY Brillion Elite Mini Monitor - Ground Speed Sensor Smart Shaft Sensor Transmission Screw,Rnd Hd #8-32 x 1-1/4 Bearing Flangette Washer,Flat #8 Quill Shaft Input Shaft Clutch Bolt,1/2-13 x 1-1/4 Nut,1/2-13 Locknut, Flange #8-32 Washer, Actuator Lock 1/2 Pick-up Assembly Set Screw, Switch Bracket Hex 3/8-16 x 1/2...
  • Page 42 ASSEMBLY Brillion Elite Mini Monitor - Rear Seed Box Seed Shaft Sensor Locknut,Flange #8-32 Bolt,5/16 x 1-3/4 Washer,Flat 5/16 Washer,Lock 5/16 Nut,5/16-18 Screw,Rnd Hd #8-32 x 1-1/4 Seed Shaft, Retainer 5/8 Square Plate Washer,Flat #8 Smart Magnet Shaft Sensor Mount Assembly Set Screw, 1/4-20 x 3/8 Figure 2-28: Brillion Elite Mini Monitor - Rear Seed Box Seed Shaft Sensor...
  • Page 43 ASSEMBLY Brillion Elite Mini Monitor Tractor 4. Attach the Monitor Mount to the Straight Bracket with #10-24 x 1 Machine Screws, Flat Washers, Lock Installation - Optional Washers, and Nuts, provided with Monitor Mount. 5. With the Brillion Elite Mini Tractor Harness, plug the 1.
  • Page 44: Lock Washer,3/8

    ASSEMBLY Acre Meter Kit - Optional 3. Transmission w/o Clutch: Attach the Pick-Up Switch Bracket to the front of the Transmission with Not Used with Brillion Elite Mini Monitor 3/16 x 1-1/4 Bolts, Lock Washers and Nuts. P/N 5K745 - Transmission w/o Clutches Transmission w/ Clutch - Optional: Attach the P/N 5K275 - Transmission w/ Clutches Pick-Up Switch Mount to the Clutch Bracket with...
  • Page 45 ASSEMBLY 7. Attach the Pick-Up Switch Ground Wire to the small Magnet Wheel Assembly hole in the Pick-Up Switch Mount with a #6-32 x 1/2 Screw, removing paint under the wire connector to Magnet assure a good electrical ground connection. 8.
  • Page 46 ASSEMBLY Console w/Clutch Control an Electric Clutch, seal the plug end using a 2-Pin Shroud and Cavity Plug to protect it from the Installation - Optional environment. See Figure 2-34. 6. Connect plug labeled “Left Front Seed Shaft Sensor” Mount Console with Clutch Control on Tractor. to the left front Seed Shaft Sensor.
  • Page 47 ASSEMBLY Console w/Clutch Control - Front Seed Shaft Sensor - Optional Shaft Sensor Bracket 1. Remove the four 10-24 x 3/4 Self Tapping Screws from the Magnet Wheel Assembly. See Figure 2-36. Position the rounded half of the Magnet Wheel Assembly on the seed shaft.
  • Page 48 ASSEMBLY Console w/Clutch Control - Rear Magnet Seed Box Seed Shaft Sensor - Coupling with Optional 1/8" Max Magnet 1. At the Transmission/left side of Seeder remove 1/4 x 1-1/2 Roll Pin from Seed Shaft Coupler. See Figure 2-38. 2. Replace Coupler with Coupler with Magnet, insert Shaft Sensor existing Roll Pin.
  • Page 49 ASSEMBLY 8. On the right hand side of Seeder, slide Magnet Mount Assembly onto Seed Shaft, ensure groove is Shaft Sensor aligned with Seed Shaft Roll Pin. Secure Set Screw Bracket to Seed Shaft. See Figure 2-40. 1/8" Max 9. Remove 5/16-18 x 1-3/4 Bolts, Nuts and Lock Washers from the Seed Shaft Retaining Plate.
  • Page 50 ASSEMBLY Console w/Clutch Control 4. Plug Console 3-Pin Power Cord into the Tractor Convenience Outlet and 9-Pin Cord into the Seeder Tractor Installation - Optional Harness. 5. Check clutch operation: Clutch will disengage when 1. Mount Angle Bracket onto Tractor where convenient power is applied.
  • Page 51 ASSEMBLY Agitator Box - (If Not Equipped) 2. Install coupling on transmission output shaft and secure with 1/4" x 1-1/2 Roll Pin. See Figure 2-43. Installation of the Agitator (Brome) Box: Loose parts are 3. Loosen U-Bolts which fasten front seed box to frame shipped in a bag assembly placed in the left Seed Box.
  • Page 52 ASSEMBLY Extended Supports Figure 2-44: Extended Supports 4. Install the left and right boxes as shown. Left box 6. Position the shift handles on rear of boxes so the pin fastens to transmission with 5/16 x 1-1/2 and 3/8 x 1 in the bottom of each handle engages the slotted Bolts, Lock Washers and Nuts.
  • Page 53 ASSEMBLY  CAUTION The brushes will be destroyed if installed backwards. Install 4C488 washers to hold bushing in box end bearing block. ROTATION Figure 2-46: Box End Bearing REAR Figure 2-48: Brush Agitator Shaft Rotation Figure 2-47: Shift Handle Agitator Installation - Optional 1.
  • Page 54 ASSEMBLY 7. Reinstall LH Seed Shaft aligning Square Bore 8. Install Center Bushing Assembly. Washers, Agitators, Bushings, and Transmission 9. Install the Agitators inside the RH Seed Box. Place Drive Coupler. Verify Seed Shaft to Transmission Square Bore Washers on each end of the Agitators. Drive Coupler engagement.
  • Page 55 ASSEMBLY Front Seed Box Dividers - Rear Seed Box Dividers - Optional Optional 1. Use upper and lower Threaded Rods and tighten Install a divider against the Agitator Bearing and then nuts on each side of original and new dividers. equally space the other dividers as equally as possible.
  • Page 56 ASSEMBLY SD Pulverizer Warning Lamp IMPORTANT Installation - Drawbar All Harnesses must be firmly attached to Machine Frame members or Hydraulic Hoses so they do not NOTE sag or become torn loose by field debris. 13. Attach the SMV Mount to the center of frame with On 8FT and 10FT Models both the Amber and Red 3/8-16 U-Bolt, Lock Washers and Nuts.
  • Page 57 ASSEMBLY Red Lamp Amber Lamp Bolt, Locknut, 1/4-20 x 1-1/4 1/4-20 Light Bracket Amber Lamp Tie Wrap Connector Mount Holder Locknut, 5/16-18 Mount Flat Washer,1/4 Bolt,5/16-18 x 1 Locknut, U-Bolt, 1/4-20 Flat Washer,5/16 3/8-16 Bolt,1/4-20 x 1 Nut,3/8-16 Lock Washer,3/8 Red Lamp Amber 7-Pin Harness...
  • Page 58 ASSEMBLY SD Pulverizer Warning Lamp IMPORTANT Installation - 3-PT All Harnesses must be firmly attached to Machine Frame members or Hydraulic Hoses so they do not NOTE sag or become torn loose by field debris. 13. Attach the SMV Mount to the center of frame with On 8FT and 10FT Models both the Amber and Red 3/8-16 U-Bolt, Lock Washers and Nuts.
  • Page 59 ASSEMBLY Amber Lamp Bolt, 1/4-20 x 1-1/4 Red Lamp Locknut,1/4-20 Amber Lamp Light Bracket Tie Wrap Mount Locknut, 5/16-18 Mount Bolt,5/16-18x1 U-Bolt, 3/8-16 Flat Washer,5/16 7-Pin Harness Nut,3/8-16 Lock Washer,3/8 Red Lamp Bolt, Amber 1/4-20 x 1 Lamp Connector Holder Light Locknut,1/4-20 Module...
  • Page 60 ASSEMBLY SD Pulverizer Warning Lamp Installation - Dimensions 5 1/2"±1" 30" 30" 5 1/2"±1" All Drawbar Models 12FT Only 12FT Only All Drawbar Models Amber Amber Lamp Lamp Mount Lamp Lamp Light Light Bracket Bracket Drawbar Models 4 1/2"±1" 30" 30"...
  • Page 61 ASSEMBLY Table provided for general use. NOTES: 1P480-0522 2-39...
  • Page 62 ASSEMBLY Scraper Kit - Optional 2. Attach the LH and RH Angle Brackets to the Brackets with 1/2-13 x 3-1/4 x 4-9/16 U-Bolts, Lock Washers and Nuts. Do not tighten at this time. IMPORTANT 3. Attach the Scraper Angle to the LH and RH Angle Cannot be used with Coil Tine Track Remover Kit.
  • Page 63 ASSEMBLY U-Bolt,1/2-13 x Lock Washer,1/2 7-1/2 x 4-1/2 Nut,1/2-13 Bracket U-Bolt,1/2-13 x Nut,3/8-16 Center 3-1/4 x 4-9/16 Scraper Lock Washer,3/8 Flat Washer,3/8 Seeder Frame Tube Scraper LH Angle Bracket Carriage Bolt, 3/8-16 x 1-1/4 Scraper Angle LH Angle Bracket SeederScraperKit Lock Washer,1/2 Nut,1/2-13 U-Bolt,1/2-13 x...
  • Page 64 ASSEMBLY S-Tine Tire Track Remover Kit - 2. Attach the Tooth Tube to the S-Tine Brackets approximately 5 inches from each end of the Tooth Optional Tube with Straps, 1/2-13 x 6 Bolts, Lock Washers and Nuts. See Figure 2-62. IMPORTANT 3.
  • Page 65 ASSEMBLY Lock Washer,1/2 U-Bolt,1/2-13 x Locknut,1/2-13 7-1/2 x 4-1/2 S-Tine Bracket Strap Clamp Locknut,1/2-13 Carriage Bolt, Lock Washer,1/2 7/16-14 x 3-1/2 Bolt,1/2-13 x 6 Tooth Tube Locknut,7/16-14 S-Tine Reversible Point Flange Locknut, SeederS-TineTrackRemoverKit 3/8-16 Duck Foot Point Plow Bolt 3/8-16 X 1-3/4 Seeder Frame Tube Figure 2-63: S-Tine Track Remover Kit - Optional...
  • Page 66 ASSEMBLY Coil Tine Track Remover - Optional IMPORTANT Cannot be used with the Scraper Kit. 1. Slide the Coil Tines onto the Round Bar so that the straight leg is frontward. See Figure 2-64. 2. Mount an Arm Weldment and a Coil Tine to the Round Bar second hole from the right end and the third hole from the left end with 3/8-16 x 3 Bolts, Flat Washers, Lock Washers and Nuts.
  • Page 67 ASSEMBLY Bolt,3/8-16 x 1-1/4 Hair Pin Cotter Adjusting Angle Place Chain in Adjusting Angle Slot Clevis Pin, 1/2 x 1-1/4 Flat Washer,3/8 Lock Screw Nut,1/2-13 Chain Lock Washer,3/8 Lock Washer,1/2 Nut,3/8-16 Bracket Bolt, Seeder Frame 1/2-13 x 1-3/4 Tube Bolt, Bolt, 3/8-16 x 2-1/2 3/8-16 x 3...
  • Page 68 ASSEMBLY Table provided for general use. NOTES: 2-46 1P480-0522...
  • Page 69 Chapter 3 Operation   DANGER DANGER Never allow anyone to ride on the seeder at any Always lock the tractor drawbar in the center time. Allowing a person to ride on the machine position when transporting the unit. Failure to do can inflict serious personal injury or death to that so can result in serious injury or death and cause person.
  • Page 70 OPERATION Tractor Preparation  DANGER The Sure Stand Seeder is available as a Pull Type or Do not allow any bystanders to stand between 3-PT mounted version. the tractor and the machine while backing up to • A Pull Type seeder is equipped to be pulled by a the machine.
  • Page 71 OPERATION Figure 3-1: 3-Point Hitch 1P480-0522...
  • Page 72 OPERATION Attaching/Detaching 3-PT Hitch Seeder Klik Pin  WARNING Disengaged To prevent the machine from tipping backward on the frame, disengage parking pin only when the seeder is fully attached to the tractor. Be sure to observe the following sequences. Parking Pin Klik Pin Figure 3-3: Parking Pin Disengaged...
  • Page 73 OPERATION Tractor Preparation/Attaching of Frame Pull Type Seeder Cylinder  DANGER Engaged Do not allow any bystanders to stand between Transport Lock the tractor and the machine while backing up to Hair Pin the machine. Cotter 1. Align the Tractor Drawbar with the machine. Raise or lower the Drawbar, as needed, using the Jack.
  • Page 74 OPERATION Attaching/Detaching Pull Type Seeder Frame Cylinder Attaching the Seeder for Field Operations: Seeder parked lowered Hair Pin 1. Attach Seeder to the Tractor. Cotter 2. Raise the Seeder fully to extend the Hydraulic Lift Cylinders and rotate the Transport Locks in the engaged position over the Cylinder Rod.
  • Page 75 OPERATION Hydraulic Lift System Transmission Electric Clutch - Optional The Drawbar Seeder is equipped with a Hydraulic Lift System to raise and lower the unit in the field. IMPORTANT  WARNING At no time use high pressure water or air to clean the Electric Clutch as damage could occur.
  • Page 76 OPERATION Brillion Elite Mini Monitor • Brillion Elite Mini Monitor is operated on a 12-Volt DC negative ground system. The monitor should be Brillion Elite Mini Monitor provides information to the connected using the existing convenience plug operator and acts as an interface for clutch control. The connection.
  • Page 77 OPERATION Front Seed Box Seed Rate IMPORTANT Adjustment If equipped, the Clutch must be disengaged when Seed Shafts are turned manually for Calibration.  WARNING Seed Rate Charts specific to Seeder Model are located inside the Seed Box Cover and in this manual. See •...
  • Page 78 OPERATION Table 3-1: Front Seed Box 8FT INDICATOR SETTING ALFALFA (UNCOATED) BAHIA BERMUDA (HULLED) BIRDSFOOT TREFOIL (BROADLEAF) BLUEGRASS (KENTUCKY) BLUE GRASS (PARK KENTUCKY) BLUE GRASS (SHERMAN BIG) CANOLA CENTIPEDE CLOVER,(ALSIKE, LADINO, SWEET, RED) CLOVER, ALYCE, CALIFORINA BUR, CRIMSON, HUMBAM CRESTED WHEAT CROWN VETCH FLAX HARDING GRASS...
  • Page 79 OPERATION Table 3-2: Front Seed Box 10FT INDICATOR SETTING ALFALFA (UNCOATED) BAHIA BERMUDA (HULLED) BIRDSFOOT TREFOIL (BROADLEAF) BLUEGRASS (KENTUCKY) BLUE GRASS (PARK KENTUCKY) BLUE GRASS (SHERMAN BIG) CANOLA CENTIPEDE CLOVER,(ALSIKE, LADINO, SWEET, RED) CLOVER, ALYCE, CALIFORNIA BUR, CRIMSON, HUMBAM CRESTED WHEAT CROWN VETCH FLAX HARDING GRASS...
  • Page 80 OPERATION Table 3-3: Front Seed Box 12FT INDICATOR SETTING ALFALFA (UNCOATED) BAHIA BERMUDA (HULLED) BIRDSFOOT TREFOIL (BROADLEAF) BLUEGRASS (KENTUCKY) BLUE GRASS (PARK KENTUCKY) BLUE GRASS (SHERMAN BIG) CANOLA CENTIPEDE CLOVER,(ALSIKE, LADINO, SWEET, RED) CLOVER, ALYCE, CALIFORNIA BUR, CRIMSON, HUMBAM CRESTED WHEAT CROWN VETCH FLAX HARDING GRASS...
  • Page 81 Seed Shafts are turned manually for Calibration. Electrical Power is required to disengage the Clutch. Brillion/Landoll assumes no liability pertaining to Seeding Rates achieved with this Seeder. Rates listed are general in nature and should be used as starting points only.
  • Page 82 OPERATION Tightener 23 Tooth Driven 15/16 Hex 37 Tooth Driven 13 Tooth Driver 26 Tooth (Optional) Figure 3-13: Transmission Drive 3-14 1P480-0522...
  • Page 83 OPERATION Speed-Up Kit - Optional 5. Move the shaft far enough to the right to remove the 13 Tooth Sprocket. Seed rates can be doubled by using a 26 Tooth Sprocket 6. Install the new 26 Tooth Sprocket. and following the procedure below: 7.
  • Page 84 Cage Agitators can be used to plant cereal grains such as wheat, oats, rye, barley and others. However, Landoll does not recommend it as a harvestable crop because the seed will only be placed in the top 1/4" to 1/2" of soil which is too shallow for a harvestable crop.
  • Page 85 OPERATION Rear Agitator Seed Box Seed Rate Calibration The provided chart was determined by laboratory tests on various samples. To find rates for specific seed lots or to calibrate for unlisted seeds, proceed as shown on the seed chart. See Tables 3-4 and Table 3-16. NOTE Planting Rates For Agitator (Rear) Box In Pounds Per Acre.
  • Page 86 OPERATION Figure 3-16: Rear Agitator Seed Box Seed Chart 3-18 1P480-0522...
  • Page 87 OPERATION Loup Acre Meter Kit - Optional To clear the total acre count, press and hold the UP and DOWN buttons for two seconds. If a password has been (After 05/15/2012) entered, you will not be able to clear the total acre count. Total acres will count from.1 to 99999 acres.
  • Page 88 OPERATION If the display shows “Ent”: You must enter your 6. Press the function button to set the width. (If screen password using the UP and DOWN buttons. When your goes blank before you press the function button, password is displayed, press the /FUNC button to test repeat steps 4 and 5).
  • Page 89 OPERATION Table 3-5: Acre Meter Settings (After 05/15/2012) Pulses Width MODEL per 400 FT (Feet) SSPT604 SSP4 SSP5 SSP6 SSP8 SSBP8 SSB8 SSP10 SSBP10 SS10 SSB10 10.0 SSP12 SSBP12 SS12 SSB12 12.0 SSP16 SS16 16.0 SSP108 SS108 SSP110 SS110 10.0 SSP112 SS112 12.0...
  • Page 90 OPERATION Table 3-6: Acre Meter Settings (Before 05/15/2012) MODEL PULSES WIDTH SSP T604 SSP4 SSP5 SSP6 SSP8 SSP10 SS10 SSP12 SS12 SSP108 SS108 SSP110 SS110 SSP112 SS112 SSP208 SSP2081 SS208 SS2081 SSP210 SSP2101 SS210 SS2101 SSP212 SSP2121 SS212 SS2121 SSP308 SS308 SSP310 SS310...
  • Page 91 OPERATION Transporting the Seeder 6. Before transporting: • Know the height and width of the implement being 1. Check and follow all federal, state, and local towed. Markers, tanks, attachments, etc. can requirements before transporting the Seeder. increase the height and width of the implement. 2.
  • Page 92 OPERATION Table provided for general use. NOTES: 3-24 1P480-0522...
  • Page 93 Chapter 4 TABLE OF CONTENTS Brillion Elite Mini Monitor Overview • Field Acres and Total Acres • Clutch Control The Brillion Elite Mini Monitor is a full featured display • (Up to 6) Six Seed Shaft Rotation Sensors designed to provide accurate information to the operator •...
  • Page 94 TABLE OF CONTENTS BRILLION ELITE MINI MONITOR 9:30AM SETTINGS BACK APP VER: 2.1.1 SPEED CLUTCH SCROLL UP SETTINGS SETTINGS INSTALL SHAFT SETUP SETTINGS DIAGNOSTICS SETTINGS DISPLAY SCROLL DOWN SETTINGS Figure 4-2: Settings Menu Display (Sure Stand Seeder) Settings Menu - Source: Shaft Sensor Speed SHAFT SHAFT...
  • Page 95 TABLE OF CONTENTS BRILLION ELITE MINI MONITOR Speed Source Displays Speed Source Icon Features Pulses Per Revolution SPEED SETTINGS BACK Pulses Per Revolution are the PULSES PER IMP. SWITCH: SOURCE: number of magnets the implement REV: SHAFT SPEED DISABLED mounted speed sensor sees in one revolution of the shaft being monitored.
  • Page 96 TABLE OF CONTENTS BRILLION ELITE MINI MONITOR Speed Calibration Implement Switch Setup All new systems require a ground Implement Switch SPEED SWITCH speed calibration to ensure Setup tells the CALIBRATION SETTINGS accurate area totals and accurate monitor if the ground speed readings. To complete the calibration, Implement Switch IMP.
  • Page 97 TABLE OF CONTENTS BRILLION ELITE MINI MONITOR Settings Menu - Remove A Sensor INSTALL Install Setup Select this option to remove a SETUP REMOVE A sensor from your existing system. RECEIVER SENSOR Select “Install Setup” icon to Learn New System, Add A Sensor, or Remove A Sensor to your machine.
  • Page 98 TABLE OF CONTENTS BRILLION ELITE MINI MONITOR Settings Menu - Settings Menu - SHAFT DIAGNOSTICS Shaft Settings Diagnostics RECEIVER SETTINGS The Diagnostics screen can help in identifying issues with Seed Shaft Settings sensors, harnessing or other items. Status reports for The Seeder can have up to six Smart Shaft Sensors that Battery Voltage, Sensors Learned, MUX Communication indicate shaft rotation.
  • Page 99 TABLE OF CONTENTS BRILLION ELITE MINI MONITOR Settings Menu - Settings Menu - DISPLAY GPS Settings Display Settings RECEIVER SETTINGS SETTINGS “GPS Settings” defines any Baudrate, Speed Corrections or the current GPS Status. DISPLAY SETTINGS BACK UNITS GPS SETTINGS BACK VOLUME BRIGHTNESS GPS BAUDRATE...
  • Page 100 TABLE OF CONTENTS BRILLION ELITE MINI MONITOR Service And Technical System Update Support The system update screen is used SYSTEM to update to newer versions of UPDATE Contact: Loup Electronics Inc. software or reset to factory default Address: 2960 N. 38th Street settings.
  • Page 101 Chapter 4 Maintenance General Torque Specifications (rev. 4/97) This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and capscrews assembled without supplemental lubrication (as received condition). They do not apply if special graphite moly-disulfide or other extreme pressure lubricants are used.
  • Page 102 MAINTENANCE Hydraulic Fitting Torque Specifications 37 degree JIC, ORS, &ORB (REV. 10/97 This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and capscrews assembled without supplemental lubrication (as received condition). They do not apply if special graphite moly-disulfide or other extreme pressure lubricants are used.
  • Page 103 MAINTENANCE Tires 9. Tighten the Slotted Nut while rotating the Hub until there is a slight resistance to wheel rotation. Then, Seeder recommended Tire Size: back the Slotted Nut off one notch, until the wheel rotates freely without end play. 9.5L-15 - 8 Ply Rating 10.
  • Page 104 MAINTENANCE Pull Type Frame Wheel Arm Tire and Wheel Assembly Wheel Hub Repack Annually Rear Roller Bearing Rear Arm Rear Roller Bearing Pull Type Seeder Frame Front Roller Bearing SL2 OpGrease 3-PT Seeder Frame Front Roller Bearing Figure 4-2: Lubrication Intervals 1P480-0522...
  • Page 105 MAINTENANCE Hydraulic Maintenance NOTE Failure to position the Clamp Band Socket Head Bolt IMPORTANT (Clamp Band open section) over the Roller Drum weld Lower the Drawbar Seeder to the ground, and relieve seam will cause Clamp Band to loosen and slide. hydraulic pressure before attempting to service any After an initial run of 5-10 hours, check the Front and hydraulic component.
  • Page 106 MAINTENANCE Chain Tension Clevis Drawbolt To adjust the Transmission Chain, loosen the 5/8" Idler Locknut Sprocket Axle Bolt and then adjust the Clevis Drawbolt Locknut to obtain about 1/8"-1/4" sag. Re-tighten the #40 Chain Idler Sprocket Axle Bolt. Be careful not to over-tighten this chain.
  • Page 107 MAINTENANCE Seed Meter Adjustment IMPORTANT Ensure the Seed Shaft can turn freely without any IMPORTANT binding when the Seed Meters are open or closed The Clutch must be disengaged when Seed Shafts after servicing. are turned manually for Calibration. 1. 1/2-13 Locknuts on both ends of the Adjusting Screw are used to adjust all Seed Meters the same amount.
  • Page 108 MAINTENANCE Agitator Box Slide Warning Lamps When properly adjusted, the holes in the slide should line When plugging in the 7-Pin Warning Lamp Connector: up with the holes in the box, when the Control Handle is 1. Make sure the Tractor has a good clean Receptacle, set at “6”.
  • Page 109 MAINTENANCE Electric Clutch - Optional display harness connector. You should see the display increment +1 with each contact of the connector terminals. IMPORTANT 4. If step 3 works then wave a magnet in front of the If your machine is equipped with an Electric Clutch at Pick-Up Switch face with it re-connected to the no time use high pressure water or air to clean it, as display and see if the display increments up.
  • Page 110 MAINTENANCE Service Tip for Brome Box • Check that Seed Boxes are level and straight from end to end. Loosen and adjust Seed Boxes from the center Problem – Brome box shaft working out to the right hand and right hand end brackets if necessary. It may also end of the Seeder and wearing out the roll pin and be necessary to make an adjustment of the Left Hand retainer plate.
  • Page 111 Chapter 5 Specifications Table 5-1: 8FT Models Product Attributes SSB 8 SSBP 8 Approximate Weight 2,220 lbs. (999 kg) 1,914 lbs. (861 kg) Working Width 8 ft. 0 in. (2.4 m) 8 ft. 0 in. (2.4 m) Transport Width 11 ft. 1 in. (3.33 m) 9 ft.
  • Page 112 SPECIFICATIONS Table 5-2: 10FT Models Product Attributes SSB 10 SSBP 10 Approximate Weight 2,527 lbs. (1,137 kg) 2,207 lbs. (993 kg) Working Width 10 ft. 0 in. (3.0 m) 10 ft. 0 in. (3.0 m) Transport Width 12 ft. 11 in. (3.88 m) 11 ft.
  • Page 113 SPECIFICATIONS Table 5-3: 12FT Models Product Attributes SSB 12 SSBP 12 Approximate Weight 2,786 lbs. (1,254 kg) 2,602 lbs. (1,171 kg) Working Width 12 ft. 0 in. (3.6 m) 12 ft. 0 in. (3.6 m) Transport Width 15 ft. 0 in. (4.5 m) 13 ft.
  • Page 114 SPECIFICATIONS Table provided for general use. NOTES: 1P480-0522...
  • Page 115 Document Control Revision Log: Date Revision Improvement(s) Description and Comments 07/2008 205rev0708 Initial Release 07/2011 205rev0711 Updated Pictures and Drawings. Incorporated ECN 35017 09/2013 205rev0913 Added LED Warning Lights 07/2018 1P480-0718 Update tractor preparation section, product attributes 06/2021 1P480-0621 ECN 47093 - Hub & Spindle Asm Update to 6 Bolt 05/2022 1P480-0522 Updated “Brush Agitator Installation”...
  • Page 116 Equipment from Landoll Company, LLC is built to exacting standards ensured by ISO 9001 registration at all Landoll manufacturing facilities. Sure Stand Seeder Models SSB8/SSB10/SSB12 SSBP8/SSBP10/SSBP12 Operator’s Manual Re-Order Part Number 1P480 LANDOLL COMPANY, LLC 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM...

Table of Contents