Related Manuals for Landoll Brillion FPS-6
Summary of Contents for Landoll Brillion FPS-6
- Page 1 Food Plot Seeder Models: FPS-6, FPSA-6, FPSB-6, FPST-6, FPSAT-6 and FPSBT-6 Operator’s Manual LANDOLL CORPORATION 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM 205rev0312 2P102...
-
Page 3: Table Of Contents
Table of Contents Introduction and Safety Information Introduction ..............1-1 Description of Unit . - Page 4 Assembly Seeder Assembly ............. . 3-1 Drawbar Installation .
-
Page 5: Introduction And Safety Information
Failure to comply with this warning can result in within 10 days of retail purchase, using the Landoll to the personal injury or death, damage Corporation Ag Products on-line registration process. -
Page 6: Understanding Safety Statements
INTRODUCTION AND SAFETY INFORMATION When applying decals to the implement, be sure to clean NOTE the surface to remove any dirt or residue. Where possible, sign placement should protect the sign from Investigation has shown that nearly 1/3 of all farm abrasion, damage, or obstruction from mud, dirt, oil etc. -
Page 7: Maintenance Safety
INTRODUCTION AND SAFETY INFORMATION Maintenance Safety When inflating tires, use a clip-on chuck and extension hose long enough to allow you to stand to one side, not in • Block the implement so it will not roll when working on front of or over the tire assembly. - Page 8 INTRODUCTION AND SAFETY INFORMATION Figure 1-3: Safety Decal Locations (1 of 2) 2P102...
- Page 9 INTRODUCTION AND SAFETY INFORMATION Figure 1-4: Safety Decal Locations (2 of 2)
- Page 10 INTRODUCTION AND SAFETY INFORMATION Table provided for general use. NOTES: 2P102...
-
Page 11: Operation
This chapter will cover the basic operation and so that it lines up with the hole in Rockshaft Lug. Install procedures for the Landoll Brillion Food Plot Seeder. Be Bent Pin. See Figure 2-2. sure to read and understand the Safety Procedures and Cautions starting on page 1-1. -
Page 12: Disc Gang Adjustment
OPERATION For operation the Drawbar link must be free to float. Disc Gang Adjustment Remove Klik Pin and Clevis Pin and install it in the Disc Gang Adjustment is accomplished by loosening the bottom hole under the link. See Figure 2-4. inner gang 3/4”... -
Page 13: S-Tine Depth Adjustment
OPERATION S-Tine Depth Adjustment S-Tine Adjustment is done by removing the pins that hold the S-Tine bars in place and moving the bar up or down to reach the desired depth (typically level with Disc Gangs). In instances where you may not want to use the S-Tine, you may raise them all the way up. -
Page 14: Chain Tension
OPERATION Optional Rear Coil Tine Optional Rear Coil Tine floats freely helping to disperse soil and residue over seeded soil and follow the contour of the land. The angle at which the tines come into contact with the soil can be adjusted by loosening the cap screws on the end brackets and rotating the pipe and tine assembly clockwise or counterclockwise. - Page 15 OPERATION Figure 2-13: Planting Rates Front Meter Box...
- Page 16 OPERATION Figure 2-14: Planting Rates Agitator Box 2P102...
-
Page 17: Seeding Techniques
OPERATION Seeding Techniques When seeding larger seeds such as soybeans or peas, it may be necessary to make additional trips after planting with the tillage unit to position the seed deeper in the soil. If planting both large and small seeds it is recommended the larger seeds are planted first and the smaller seeds such as clover, alfalfa and bursitis are planted on the last trip over the soil to ensure the small seeds are not placed... -
Page 18: Seed Rate Adjustment - Rear Agitator Box
OPERATION Figure 2-17: Seed Rate Adjustment (2 of 2) Seed Rate Adjustment - Rear Agitator Adjusting the Box Slide: When properly adjusted the holes in the slide should line up with the holes in the box, with the control handle set at “6”. To make an adjustment or loosen the control handle on the box, move the slide until the holes line up. - Page 19 OPERATION Figure 2-18: Seed Rate Max Adj Rear Agitator (1 of 3) Figure 2-20: Seed Rate Adj. Rear Agitator (3 of 3) Figure 2-19: Seed Rate Min Adj Rear Agitator (2 of 3)
-
Page 20: Seed Rate Calibration
OPERATION Seed Rate Calibration See Figures 2-21 and 2-22 for detailed seed rate calibration instructions. The wrench provided with the machine can be used for calibration purposes. Figure 2-21: Front Meter Box Figure 2-22: Rear Agitator Box 2-10 2P102... -
Page 21: Assembly
Chapter 3 Assembly • Park the seeder in a work area that has a level CAUTION surface and make sure it is blocked securely so that it cannot roll. Do not work on or under this machine unless securely blocked and supported by a hoist or Seeder Assembly tractor or by other sufficient means! Support the frame and seedbox assembly with a hoist or... -
Page 22: Drawbar Installation
ASSEMBLY Drawbar Installation 1. Remove 3-Point Hitch Assembly and Link Weldment. 2. Attach Drawbar to the outside of the Frame with two 1-8 X 2-1/2" Capscrews, Bushings, Flat Washers and Lock Nuts. See Figure 3-1. 3. Install Drawbar Link's slotted end between the Frame Mast and place the Transport Lock Straps on each side of the Mast. -
Page 23: Hydraulic Hose Installation
ASSEMBLY 3. Turn O-Ring end of each Adapter Fitting into each WARNING Coupler. Insert JIC end of Adapter into the end of each hose. See Figure 3-4.Tightening Procedure For Escaping fluid under pressure can be nearly JIC 37° Swivel Female Nuts invisible and have enough force to penetrate the 1. -
Page 24: Optional Coil Tine
ASSEMBLY Optional Coil Tine 2. Assemble RH and LH Coil Tine Brackets into Frame End Plates upper 21/32" hole with 5/8-11 x 1-3/4 1. Install into each Frame End Plates lower 21/32" hole Capscrews, Flat Washer and Locknut. a 5/8-11 x 1-3/4" Capscrew, four Flat Washers and 3. -
Page 25: Field Installation Of Meter Box
ASSEMBLY Field Installation of Meter Box 9. Turn 5/8-11 hex nut onto Seed Shaft Extension. 10. Take 56 Pitch Chain and add the 4 pitch section to it. Remove existing Seedbox Drive Chain which is no longer Install Chain. See Figure 3-10. needed. - Page 26 ASSEMBLY Figure 3-7: Meter Box Front and Rear View 2P102...
-
Page 27: Field Installation Agitator Box
ASSEMBLY Field Installation Agitator Box Remove the four 5/16-18 x 3/4" capscrews, lock washers and hex nuts and reverse the deflector so that the upper The deflector on the front box must be reversed prior to flare edge faces rearward instead of forward. Re-insert installing the Agitator Box. - Page 28 ASSEMBLY Figure 3-9: Agitator Box Assembly Figure 3-10: Double Seedbox Drive Chain 2P102...
-
Page 29: Optional Rock Box
ASSEMBLY Optional Rock Box • Attach Rock Box to Frame angles just in front of the Seedbox with 1/2-13 x 1-1/2 capscrews, flat washers and lock nuts. See Figure 3-11. Figure 3-11: Rock Box Optional Positive Drive Roller 5. Starting with the left side of the scraper assembly, move the second scraper so the gap between it and 1. - Page 30 ASSEMBLY Table provided for general use. NOTES: 3-10 2P102...
-
Page 31: Preventative Maintenance
Chapter 4 Preventative Maintenance General Torque Specifications This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and capscrews assembled without supplemental lubrication (as received condition). They do not apply if special graphite moly-disulfide or other extreme pressure lubricants are used. -
Page 32: Fasteners
PREVENTATIVE MAINTENANCE METRIC: Coarse thread metric class 10.9 fasteners and class 10.0 nuts and through hardened flat washers, phosphate coated, Rockwell “C” 38-45. Use value in [ ] if using prevailing torque nuts Nominal Newton Foot Nominal Newton Foot thread Meters Pounds Thread... -
Page 33: Lubrication
PREVENTATIVE MAINTENANCE Lubrication Lubricate bearings with quality grease per recommended lubrication frequency intervals indicated or if machine is not used for an extended period. Greaseable components are the same on each side. Lubricating Wheel Hub: Grease Wheel Hubs every 40-60 hours. Repack Wheel Hub bearings annually before each season usage. -
Page 34: Transmission Chain Tension Adjustment
PREVENTATIVE MAINTENANCE Transmission Chain Tension If adjustment is needed loosen the hex nut on the Idler and slide the Idler until the proper sag is achieved. Adjustment The Seedbox Drive Chain is properly adjusted when it has 1/8” - 3/16” deflection across the sprockets. See Figure 4-4. -
Page 35: Chain Maintenance
PREVENTATIVE MAINTENANCE Chain Maintenance • For best penetration, lubricate chain immediately after use while chain is still warm. See Figure 4-5. CAUTION Do not lubricate chain while machine is in motion. If any guards are removed for lubrication, they must be replaced before operating •... -
Page 36: Firming Roller
PREVENTATIVE MAINTENANCE Firming Roller Check Firming Roller regularly for tightness between wheel, if adjustment is needed loosen the Lock Nut and slide the Star Sprocket weldment over. Re-tighten the Lock Nut. See Figure 4-6. Figure 4-6 Firming Roller 2P102... -
Page 37: General Reference And Specifications
Chapter 5 General Reference and Specifications Table 5-1: Pick-Up Type Seeders Food Plot Seeder Specifications FPS-6 FPSA-6 FPSB-6 Approximate Weigh 1,284 lbs. (578 kg) 1,266 lbs. (570 kg) 1,389 lbs. (625 kg) Working Width 6 ft. 0 in. (1.8 m) 6 ft. - Page 38 GENERAL REFERENCE AND SPECIFICATIONS Food Plot Seeder Specifications FPS-6 FPSA-6 FPSB-6 Seed Meter/Opening Spacing 6 in. (152 mm) 4 in. (102 mm) 6 in. (152 mm) / 4 in. (102 mm) Seed Delivery Broadcast with Wind Deflector Broadcast with Wind Deflector Broadcast with Wind Deflector Tray Tray...
- Page 39 GENERAL REFERENCE AND SPECIFICATIONS Food Plot Seeder Specifications FPST-6 FPSAT-6 FPSBT-6 Arbor Bolt 1.125 in. (28.6 mm) Square 1.125 in. (28.6 mm) Square 1.125 in. (28.6 mm) Square Gang Bearings 1.125 in. (28.6 mm) Greaseable 1.125 in. (28.6 mm) Greaseable 1.125 in.
- Page 40 GENERAL REFERENCE AND SPECIFICATIONS Page Intentionally Blank 2P102...
- Page 41 Document Control Revision Log: Date Revision Improvement(s) Description and Comments 7/7/2008 205rev7-7-08 Initial Release 9/15/2011 205rev0911 Incorporated improved pictures and drawings. Incorporated ECN’s 35017 and 35166 3/18/2012 205rev0312 Incorporated ECN 35504. Corrected Planting Rate Values.
- Page 42 Equipment from Landoll Corporation is built to exacting standards ensured by ISO 9001 registration at all Landoll manufacturing facilities. Food Plot Seeder Models FPS-6, FPSA-6, FPSB-6, FPST-6, FPSAT-6 and FPSBT-6 Operator’s Manual Re-Order Part Number 2P102 LANDOLL CORPORATION 1900 North Street...