MacDon M100 Unloading And Assembly Instructions page 34

C x x x || T O
L1
M x x x ||
L2
C x x x || T O
L1
M x x x ||
L2
M x x x ||
L2
M x x x || H D R
L1
M x x x || E X T E N D
L2
C x x x || C A L I B R A T I N G
L1
M x x x || E X T E N D
L2
M x x x || E X T E N D
L2
M x x x || H D R
L1
M x x x || P R E S S
L2
C x x x || C A L I B R A T I N G
L1
M x x x || R E T R A C T
L2
M x x x || H D R
L2
C x x x || T O
L1
M x x x ||
L2
M x x x ||
L2
C x x x || E X I T
L1
M x x x ||
L2
L1 C x x x || D I A G N O S T I C
L2 M x x x ||
C x x x || V I E W
L1
M x x x ||
L2
L1
L2
L1
L2
L1
L2
L1
L2
C x x x || E N T E R
L1
M x x x ||
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
Form # 169390
UNLOADING AND ASSEMBLY
C A L I B R A T E
H E A D E R H E I G H T
C A L I B R A T E
H E A D E R H E I G H T
H E A D E R T I L T
T I L T S E N S O R
T L T T O
T I L T
T I L T
T I L T
T I L T S E N S O R
R E T R A C T
T I L T
T I L T
T I L T C O M P L E T E
C A L I B R A T E
H E A D E R T I L T
S T O P & E X I T
C A L I B R A T I O N ?
N O / Y E S
M O D E ?
N O / Y E S
E R R O R C O D E S ?
N O / Y E S
C x x x || V I E W
T R A C T O R
M x x x ||
N O / Y E S
1 || 1 2 3 4 . 5
4 7 || S E N S O R
E
2 || 1 2 3 4 . 5
7 1 || L O W
E H Y D R A U L I C
C x x x || E X I T
T R A C T O R
M x x x ||
N O / Y E S
S E N S O R
N O / Y E S
C x x x || H E A D E R
M x x x ||
E N A B L E / D I S A B L E
C x x x || H E A D E R
M x x x ||
E N A B L E / D I S A B L E
C x x x || K N I F E
S P E E D
M x x x ||
E N A B L E / D I S A B L E
C x x x || R E E L
S P E E D
M x x x ||
E N A B L E / D I S A B L E
C x x x || E X I T
S E N S O R
M x x x ||
N O / Y E S
S E L E C T The menu will display the last item selected when the
calibration routine is completed.
S E L E C T
C A L
S T A R T
If the HEADER TILT option in the TRACTOR SETUP
H O L D
is set to NO then only HEIGHT should be available
D O N E
as a menu selection for calibration.
C A L
T I L T
H O L D
S E L E C T
T O C A L I B R A T E
If "NO" then jump to:
T R A C T O R S E T U P ?
E N T E R
C O D E S ?
H R S 1 2 3
V O L T S L O W
H R S 1 2 3
O I L
C O D E S ?
S E T U P ?
R E A D
H T S E N S O R
T I L T S E N S O R
S E N S O R
S E N S O R
S E T U P ?
32
If "NO" then jump to:
S E L E C T
If "NO" then jump to:
S E N S O R S E T U P ?
If "NO" then jump to:
E N T E R S E N S O R
The last 10 distinct error codes are stored along with
the code #, Exxx, engine hours and number of
occurrences. The "arrow" keys are used to cycle
between codes.
If "NO" then jump to:
V I E W T R A C T O R
If "NO" then jump to:
S E N S O R I N P U T S ?
The operator can select each sensor and selectively
enable or disable the sensor in the event of a sensor
malfunction.
If no expansion module or an A30 auger header is
selected, the corresponding menu items should be
suppressed.
When "SELECT" is pressed the program goes to the
EXIT SENSOR SETUP? selection.
If "NO" then jump to:
K N I F E S P E E D
Or to the first sensor "installed"
(continued next page)
S E T U P ?
C O D E S ?
S E N S O R
Model Year - 2010