Table of Contents
Advertisement
(Key On / Engine Running or Not / Header Disengaged).
(Press PROGRAM and SELECT on CDM to enter programming mode).
L1 C x x x || T R A C T O R
L2 M x x x ||
C x x x || S E L E C T
L1
M x x x ||
L2
C x x x || S E L E C T
L1
M x x x ||
L2
C x x x || S E L E C T
L1
M x x x ||
L2
C x x x || T I L T
L1
M x x x ||
L2
C x x x || R E E L
L1
M x x x ||
L2
C x x x || K N I F E
L1
M x x x ||
L2
C x x x || H E A D E R
L1
M x x x ||
L2
M x x x ||
L2
C x x x || R E T U R N
L1
M x x x ||
L2
M x x x ||
L2
C x x x || H E A D E R
L1
M x x x ||
L2
C x x x || H A Y
L1
M x x x ||
L2
C x x x || A U G E R
L1
M x x x ||
L2
M x x x ||
L2
C x x x || S E T
L1
M x x x ||
L2
M x x x ||
L2
M x x x ||
L2
M x x x ||
L2
C x x x || S E T
L1
M x x x ||
L2
C x x x || S E T
L1
M x x x ||
L2
Form # 169390
UNLOADING AND ASSEMBLY
DETAILED PROGRAMMING INSTRUCTIONS
S E T U P ?
N O / Y E S
H E A D E R
D R A P E R
H E A D E R
A 3 0
A U G E R
H E A D E R
A 4 0
A U G E R
C Y L
I N S T A L L E D ?
N O / Y E S
F O R E / A F T ?
N O / Y E S
O V E R L O A D
1 0 0 0
S P M
I N D E X
R E E L
&
C O N V E Y O R
R E E L
O N L Y
T O
C U T
H E I G H T
&
H E I G H T
O N L Y
C U T
W I D T H ?
2 0 . 5
F E E T
C O N D I T I O N E R ?
N O / Y E S
H D R
R E E L
R P M / M P H
R P M / K P H
T I R E
S I Z E ?
1 8 . 4 X 2 6
1 8 . 4 X 2 6
2 3 . 1 X 2 6
6 0 0 - 6 5
R 2 8
E N G I N E
O F F / O N
C O N T R O L
N O / Y E S
C x x x || D R A P E R
L1
M x x x ||
L2
E N A B L E D / L O C K E D
C x x x || A U G E R
L1
M x x x ||
L2
E N A B L E D / L O C K E D
C x x x || R E E L
L1
M x x x ||
L2
E N A B L E D / L O C K E D
C x x x || R E E L
L1
M x x x ||
L2
E N A B L E D / L O C K E D
C x x x || H E A D E R
L1
M x x x ||
L2
E N A B L E D / L O C K E D
C x x x || E X I T
L1
M x x x ||
L2
Programming Menu Flow Chart
If "NO" then jump to:
C A B
D I S P L A Y
T Y P E ?
Selects the header type, the selected header will be
flashing. The "factory" default to be DRAPER.
T Y P E ?
If the A30 is selected then the reel speed should be
suppressed as there is no reel speed sensor.
T Y P E ?
If a DRAPER or A40 is selected the reel speed
should be enabled (with expansion module installed).
The TILT selection needs to be available even if the
expansion module is not installed.
S P D ?
Knife Overload Speed should be suppressed unless
the expansion module is installed.
M O D E ?
If the REEL SPEED sensor is not "installed" (A30
Auger Header selected) in the TRACTOR SETUP
menu, the INDEX mode should be suppressed.
M O D E ?
If the HEADER TILT sensor is not "installed" (no
expansion module installed), then the RTC mode
T I L T
should default to HEIGHT only.
Use the "arrow" keys to set the header cut width.
DRAPER HEADER ONLY. Default will be flashing.
S P D
T U R F
Pressing "SELECT" will go to the next line 1 (L1)
menu selection. The turn signal "arrow" keys are
B A R
T U R F
I S C
R P M ?
S E T
L O C K S ?
V I E W
S P E E D
S P E E D
S P E E D
F O R E / A F T
T I L T
C O N T R O L
L O C K S ?
N O / Y E S
30
S E T U P ?
Use "arrow" keys to select.
AUGER HEADER ONLY
For IMPERIAL display.
For METRIC display.
used to change the values.
Pressing "SELECT" will jump to:
C O N T R O L
L O C K S ?
If "NO" then jump to:
C O N T R O L
L O C K S ?
This menu allows the operator to selectably "lock out"
the control functions for the various header functions.
The default or selected "status" for each item will
flash.
If the expansion module is not installed the
corresponding menu items should be suppressed.
The "arrow" keys are used to ENABLE or LOCK OUT
each function. Pressing "SELECT" will go to the next
L1 menu item.
Tilt to be suppressed if not "installed" in the tractor
setup menu.
If "NO" then jump to:
D R A P E R
S P E E D
E N A B L E D / L O C K E D
(continued next page)
Model Year - 2010
Advertisement
Table of Contents
