Christie CP2208 User Manual

Hide thumbs Also See for CP2208:

User manual (110 pages)

Service manual (89 pages)

Installation and setup manual (35 pages)

Table Of Contents

Table of Contents

Quick Links

Download this manual

User Guide

020-101916-03

CP2208

Table of Contents

Troubleshooting

Summary of Contents for Christie CP2208

Page 1 User Guide 020-101916-03 CP2208...
Page 2 Christie's control such as maintenance of the product in proper working conditions. Performance specifications are based on information available at the time of printing. Christie makes no warranty of any kind with regard to this material, including, but not limited to, implied warranties of fitness for a particular purpose.
Page 3 China RoHS compliance information 关于中国《子信息品染控制管理法》的明 Environmentally Friendly Use Period • 保使用期限 The year number in the centre of the label indicates the Environmentally Friendly Use Period, which is required to mark on the electronic information product sold in China according to the China RoHS regulations.
Page 4 表示有害物在部件所有均材料中的含有均在 GB/T 26572 定的限量要求以下。 X: indicates that said hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement of GB/T 26572. 表示有害物至少在部件的某一均材料中的含有超出 GB/T 26572 定的限量要求。...
Page 10 CP2208 Specifications........
Page 11: Installing And Setting Up
These operators are qualified to replace the lamp and air filter, but should not attempt to install or service the projector Only Christie qualified technicians who are knowledgeable about the hazards associated with high- voltage, ultraviolet exposure, and the high temperatures generated by the projector lamp are authorized to assemble, install, and service the projector.
Page 12: Ac/Power Precautions
FIRE HAZARD! Do not use a power cord, harness, or cable that appears damaged. Caution! If not avoided, the following could result in minor or moderate injury. • Only Christie qualified technicians are permitted to open product enclosures. • Install the product near an easily accessible AC receptacle.
Page 13: Projector Components - Front
Position the projector so it is centered and parallel with the theater screen. If space is limited, aim the projector slightly off-center and use lens offset to center the image on the screen. Stacking projectors To stack CP2208 projectors, use the stacking kit provided. The stacking kit includes these parts: CP2208 User Guide 020-101916-03 Rev.
Page 14 2. Position a single stacking cup (011-104349-XX) over one of the empty screw holes so the higher side of the cup faces outward and aligns with the projector skin. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 15 Install the lamp. d) Connect devices to the projector. e) Connect power. Adjust the bottom projector image to fit the screen. . CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 16: Adjusting Tilt And Leveling The Projector
Lock Turn to adjust height 2. Extend or retract the feet. 3. When the adjustment is correct, tighten the lock nut. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 17: Installing The Touch Panel Controller
Complete the following procedure to install the lamp. Warning! If not avoided, the following could result in death or serious injury. • This procedure must be performed by Christie qualified technicians. • EXPLOSION HAZARD! Always wear manufacturer approved protective safety clothing (gloves, jacket, face shield) whenever the lamp door is open or when handling the lamp.
Page 18 18. Close and lock the rear access door. Ensure the hex key is placed back into its holder before closing the rear access door. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 19: Connecting Power
• SHOCK HAZARD! A dedicated, protected ground or earth wire must be installed on the product by Christie qualified technicians or electricians before it can be connected to power. • SHOCK HAZARD! Only use the AC power cord provided with the product or recommended by Christie.
Page 20: Connecting Devices And Establishing Communication
• STBY—The LED is green when the standby power supply is active. If the LED is not illuminated, the standby power supply has failed or the projector circuit breaker is off. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 21: Connecting The Projector To A Computer
You must turn on the light source manually. Connects the projector to 3D devices. Connects the projector to Christie or third-party automation equipment. Connects the projector to a 10Base-T/100Base-TX Ethernet connection. Connects the projector to high-definition cinema sources. The connectors can be used together to deliver Dual Link HD-DVI following the SMPTE 372M standard.
Page 22: Turning The Projector On
1. On the touch panel controller (TPC), log on to the projector (on page 22) with administrator or service permissions. 2. Select Menu > Administrator Setup > Communications Configuration. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 23: Adding The Lamp Information To The Lamp History
The baud rate of the serial port. The default is 115200. Enable SNMP Enables SNMP. SNMP V2 / SNMP V3 The SNMP protocol type. Contact Christie for the SNMP V3 user ID and password. Management IP The IP address where SNMP information and notifications are sent.
Page 24: Turning The Lamp On
1. Verify that the projector is properly positioned relative to the screen (on page 13). 2. Display the RGB-12bit-Full Screen White test pattern (on page 66). CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 25: Aligning Dual Projector Images
) icon on the main screen and then select the left ( ), right ( ), up ( ), or down ( CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 26: Playing Content
Connect the projector to a device with an HDMI to DVI connection. b) Connect the audio output cables to an audio processor. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 27 Install an Integrated Media Block (IMB). b) Connect the projector to a network-attached storage (NAS) or direct attached storage (DAS) device. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 28: Adjusting The Image
Learn how to correct horizontal keystone. 1. On both projectors, turn the light source on and open the douser (on page 24). CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 29: Correcting Dual Projector Vertical Keystone
4. On the bottom projector, display the DC2K Framing Red test pattern. (on page 66) 5. Identify which projector has the vertical keystone issue. In this example, the top projector has the vertical keystone issue. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 30: Correcting Vignetting
When adjusting boresight, you must maintain the boresight distance from the lens to the prism plane set by Christie. For example, when you move the top screw outward, turn the bottom two boresight screws to maintain the overall distance.
Page 31: Adjusting Horizontal Boresight
When adjusting boresight, you must maintain the boresight distance from the lens to the prism plane set by Christie. For example, when you move the top screw outward, turn the bottom two boresight screws to maintain the overall distance.
Page 32: Adjusting Digital Micromirror Device Convergence
Normally, the three colors should overlap precisely to form pure white lines throughout the image and one or more poorly converged individual colors may appear adjacent to some or all of the lines. Contact your Christie accredited service technician to correct DMD convergence issues. Adjusting the fold mirror Learn how to align the fold mirror with the optical system to correct an image with missing or shadowy corners or edges.
Page 33 Install movable flat black panels or curtains along each side of the screen. b) Close the curtain for flat images or open the curtain and zoom for scope images. Side masking theater (2.39 screens) CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 34: Calibrating Screen Brightness (Fl)
2. On the touch panel controller, tap Menu > Administrator Setup > Foot Lamberts Calibration. 3. Complete the Foot Lamberts Calibration wizard. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 35: Accessing Projector Diagnostics
A boot delay occurs if you turn the on before turning on the projector power. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 36: Logging On To The Projector
2. From the Username list, select a user name. Each user account has set user access permissions. 3. In the Password field, type the password. 4. Tap Login. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 37: Viewing The Status Of Projector Components
Running the projector interrogator The interrogator captures diagnostic information that you can use to assist Christie service technicians diagnose and correct projector issues. Image disruption can occur if you run the interrogator during a show. When you run the interrogator, you cannot modify projector settings.
Page 38: Running A Server Test
3. If you are servicing the projector or removing the protective cover, disconnect the AC power and turn the breaker off. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 39: Managing The Digital Light Processing
1. On the touch panel controller (TPC), log on to the projector (on page 22) with administrator or service permissions. 2. Select Menu > Diagnostics > DLP Management. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 40: Downloading An Integrated Cinema Processor Certificate
2. Select Menu > Diagnostics > DLP Management. 3. Select DLP Self Test. 4. Select Yes. To re-enable the ICP signature test, clear the Bypass Signature Test check box. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 41: Managing Lamp Information
3. Select Save As. 4. Enter a name for the lamp file in the Filename field. 5. Select OK. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 42: Modifying An Existing Lamp File
View the information collected on previously used lamps. 1. Select Menu Advanced Setup Lamp History. 2. Review the information displayed in the history. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 43: Receiving An Alarm When A Lamp Reaches Its Expiry Date
1. Select Menu > Advanced Setup > Lamp Power/LiteLOC Setup. 2. Review the current light intensity value displayed in the Intensity field. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 44: Working With Channels
Any changes made to the ILS file settings are applied to all channels that use this ILS file. 7. In the left pane, select Config 2. 8. Complete the following fields: CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 46 Values between -180 and 180 are accepted. To enter the phase delay value, select the Launch Dialog icon: 11. To activate the channel, select Activate. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 47: Activating A Channel
1. On the touch panel controller (TPC), log on to the projector (on page 22) with administrator or service permissions. 2. Select Menu > Administrator Setup > Preferred Channel Setup. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 48 4. To remove a channel from the Preferred Channels pane, select and drag a channel from the Selected Channel Buttons (Drag and Drop) pane to the recycle bin in the bottom right corner. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 49: Managing Projector Setting Files
The same screen file can be assigned to multiple input devices. 1. On the touch panel controller (TPC), select Menu > Advanced Setup > Screen File Setup. 2. Select Save As. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 50: Modifying A Screen File
11. If the MCGD file will be associated with a 3D channel, select Enable 3D and select a frame rate. 12. Select Save. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 51: Modifying A Measured Color Gamut Data File
Create a new file for the intelligent lens system (ILS). 1. On the touch panel controller (TPC), select Menu > Advanced Setup > ILS File Setup. 2. Select Save As. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 52: Editing An Existing Intelligent Lens System File
1. On the touch panel controller (TPC), select Menu > Advanced Setup > ILS File Setup. 2. From the Current ILS File list, select an ILS file. 3. Select Quick Reset. 4. Select Yes. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 53: Adding A Lens Serial Number
2. From the Primary Lens list, select a lens. 3. In the Intelligent Lens System area, tap Full Calibration. 4. Tap Yes. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 54: Resetting The Intelligent Lens System And The Lens Position
2. From the Primary Lens list, select a lens. 3. In the Intelligent Lens System area, select Quick Reset. 4. Select Yes. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 55: Scheduling Events
1. On the touch panel controller (TPC), log on to the projector (on page 22) with administrator or service permissions. 2. Select Menu > Administrator Setup > Scheduler. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 56: Deleting A Scheduled Event
2. On the touch panel controller (TPC), select Menu > Administrator Setup > Scheduler. 3. Select to clear the Enable Scheduler check box. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 57: Viewing And Modifying Projector Settings
2. Select Menu > Administrator Setup > Communications Configuration. 3. Complete these fields: Field Description Device Name The name of the projector. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 58: Adding A Network Device
Accessing a network device Learn how to interact with network devices. 1. On the touch panel controller (TPC), select Menu > Network Devices > Christie ACT. 2. To interact with the device select in the top-right corner of the window.
Page 59: Calibrating The Internal Light Meter
Use the Microsoft Network Connections window to view and modify network connections. 1. On the touch panel controller (TPC), select Menu > Service Setup > System Access. 2. Select Network Connections. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 60: Viewing Projector Information
(DLP) version, and the lens type. • On the touch panel controller (TPC), select Menu > About. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 61: Managing User Accounts
2. Select Menu > Administrator Setup > User Accounts. 3. Select Add. 4. In the Username field, select the Launch Dialog icon: 5. Enter the user name and select Enter. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 62: Changing A User Account Password Or Permissions
2. Select Menu > Administrator Setup > User Accounts. 3. From the Username list, select a user name. 4. Select Delete. 5. Select Yes. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 63: Backing Up, Restoring, And Upgrading Projector Files
1. On the touch panel controller (TPC), log on to the projector (on page 22) with administrator or service permissions. 2. Select Menu > Administrator Setup > Upgrade. 3. In the Available Upgrade Files list, select an upgrade file. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 64: Backing Up Projector Settings And Information
1. On the touch panel controller (TPC), log on to the projector (on page 22) with service permissions. 2. Select Menu > Service Setup > File Management. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 65: Moving Files To The Projector
2. In the File Type list, select a file type. 3. Select and drag a file from the Projector Files pane to the trash can icon. 4. Select Yes. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 66: Test Patterns
3. To turn the test pattern on, in the Preferred Test Patterns pane, double-tap the test pattern. 4. Tap Full Screen (Ignore screen file settings). CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 67: Viewing 3D Content
Viewing 3D content Configure the hardware and software for viewing 3D presentations. Display requirements To display 3D images with the CP2208 projector, you require the following items. • A 3D hardware system: • Pi-Cell polarizer for display on a screen that has a silver polarization-preserving surface for use with passive glasses (RealD).
Page 69: Creating A High Frame Rate 3D File
True: 3D L/R sync output from GPO will match L/R sync input. Inverted: 3D L/R sync output from GPO will be the opposite of sync input (left = right, right = left). CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 70: Editing The Default 3D Lamp File
4. In the Red, Green, Blue and White fields, enter the x and y values. 5. Select Save As. 6. In the File Name field, enter 3D Onsite. 7. Select Save. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 71: Editing The 3D Flat 1998 X 1080 Channel
From the Screen File list, select Scope. 4. In the left pane, select Config 2 and edit these settings: a) From the Measured Color list, select 3D Onsite. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 72: Displaying 3D Diagnostic Test Patterns
1. Put on a pair of 3D glasses. 2. Play the 3D content. 3. Verify the left and right eye display correctly. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 73: Troubleshooting 3D
RealD XL device. Resolution 1. Select Menu > Advanced Setup > Lamp Power/LiteLOC Setup. ™ 2. Increase the value in the Power % field. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 74: No 3D Effect
2. From the Channel Name list, select a 3D channel. 3. In the left pane, select 3D Control. 4. From the L/R Display Sequence list, select Left (L1R1 L2R2). CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 75: Maintaining The Projector
• Caution! If not avoided, the following could result in minor or moderate injury. • Christie products must be installed and serviced by Christie qualified technicians. • Only Christie qualified technicians are permitted to open product enclosures. Notice. If not avoided, the following could result in property damage.
Page 77: Inspecting And Cleaning Optics
Typically, optical components do not need to be cleaned frequently if they are installed and operated in a location that meets or exceeds the environmental standard recommended by Christie. Christie recommends that all cinema projectors are installed and operated in an environment that meets or exceeds Underwriters Laboratories (UL) standard 609.50 Pollution Degree 2 and ISO Class 9 Standard...
Page 78: Inspecting The Card Cage Filter
3. Open the integrator rod access door and loosen the second service panel screw. 4. Push the clips on the top of the service panel down and out to remove the service panel. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 79 8. Install the cap plate and tighten the two captive screws. 9. Install the service panel and then tighten the two screws. 10. Install the top lid. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 80: Cleaning A Washable Filter
9. Insert the lens until it connects with the magnets on the mount. When the lens contacts the magnetic plates it is seated correctly. 10. Secure the lens clamp by rotating it clockwise. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 81 Maintaining the projector 11. Tighten the lens mount cap screws for added stability. 12. Remove the lens cap from the front of the lens. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 82: Troubleshooting
Listen for a clicking noise that indicates the ballast is attempting to strike the lamp. If you do not hear a clicking noise, there might be a problem with the ballast. Contact a Christie accredited service technician to resolve the issue.
Page 83: Lamp Suddenly Turns Off
Ensure any test pattern other than the full black test pattern displays properly. • Verify the correct display file is selected. • For cinema connections, verify the correct port is selected. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 84: Severe Motion Artifacts
Add signal amplification or conditioning if the distance between the input device and the projector exceeds 25 feet. • Turn the projector off and then on again. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 85: Display Has Suddenly Frozen
Inconsistent picture quality The quality of the projected image keeps changing. Resolution Verify the quality of the signal from the input source. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 86: Touch Panel Controller Issues
If the location of button presses on the screen are not interpreted correctly, the TPC screen may need recalibrating. Resolution 1. Select Menu > Administrator Setup > Preferences. 2. Select Calibrate Screen and follow the onscreen instructions. CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 87: Cp2208 Specifications
Item Description Activation Discrete switch above the power inlet cord(s) UPS inlet connector IEC-320-C13/10 A, 240 VAC (rating for powering main electronics) CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 88: Environmental Specifications
Pixel format (H x V square pixels) 2048 x 1080 Processing path 23.97 - Achievable brightness (measured at screen center) Achievable contrast ratio 400:1 ANSI CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 89: Control Signal Compatibility
Connector 15-pin subminiature D, female Bit Rate 1,200 bps Data Format 1 start bit, 8 data bits, 1 stop bit, no parity CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 90: Touch Panel Controller Specifications
Lamp expiry hours This table specifies the maximum hours the projector lamp can operate before replacement: Lamp Type Expected Life CDXL-14M 3500 hours CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 91: Accessories
Replacement Air Filter (003-002311-XX) • Replacement Light Engine Washable Air Filter (003-004654-XX) • Replacement Card Cage Washable Air Filter (003-004655-XX) Miscellaneous • Rack Stand (108-416102-XX) CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 92: Regulatory
This product conforms to the latest regulations and standards related to product safety, environmental, and electromagnetic compatibility (EMC) requirements. Safety Electro-magnetic compatibility Emissions Immunity Environmental CP2208 User Guide 020-101916-03 Rev. 1 (12-20120) Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Page 93 Corporate ofﬁ ces Worldwide ofﬁ ces Christie Digital Systems USA, Inc. Africa Columbia Mexico United States (Arizona) ph: 714 236 8610 ph: +27 (0)11 510 0094 ph: +57 (318) 447 3179 ph: +52 55 4744 1790 ph: 602 943 5700...

Christie CP2208 User Manual

Installing and Setting up

Adjusting the Image

Accessing Projector Diagnostics

Managing the Digital Light Processing

Managing Lamp Information

Working with Channels

Managing Projector Setting Files

Scheduling Events

Viewing and Modifying Projector Settings

Managing User Accounts

Backing Up, Restoring, and Upgrading Projector Files

Test Patterns

Viewing 3D Content

Maintaining the Projector

Troubleshooting

CP2208 Specifications

Quick Links

Troubleshooting

Related Manuals for Christie CP2208

Summary of Contents for Christie CP2208

Table of Contents