1. Manuals
  2. Brands
  3. Christie Manuals
  4. Projector
  5. Solaria CP2210
  6. Setup manual

Christie CP2210 Setup Manual

Christie high-brightness projection systems setup guide
Hide thumbs Also See for CP2210:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service Manual, User Manual
CP2210
S e t u p G u i d e
020-100524-04

Advertisement

Table of Contents
loading

Related Manuals for Christie CP2210

Summary of Contents for Christie CP2210

  • Page 1 CP2210 S e t u p G u i d e 020-100524-04...
  • Page 3 CP2210 S e t u p G u i d e 020-100524-04...
  • Page 4 Performance specifications are based on information available at the time of printing. Christie makes no warranty of any kind with regard to this material, including, but not limited to, implied warranties of fitness for a particular purpose. Christie will not be liable for errors contained herein or for incidental or consequential damages in connection with the performance or use of this material.

  • Page 7: Table Of Contents

    3.4 Connect Devices to the GPIO Port ....................3-3 3.5 Connect Devices to the 3D Connector ..................3-5 4: Adjust the Image 4.1 Maximize Light Output .......................4-1 4.2 Calibrate Screen Brightness (fL) ....................4-1 4.3 Basic Image Alignment .......................4-2 CP2210 Setup Guide 020-100524-04 Rev. 1 (05-2014)
  • Page 8 7.11 Image Appears Vertically Stretched or Squeezed into Center of Screen ........7-3 7.12 No Image, Just Pink Snow ......................7-3 7.13 Inaccurate Display Colors......................7-3 7.14 Display is Not Rectangular .......................7-4 7.15 Display is Noisy........................7-4 7.16 Display has Suddenly Frozen ....................7-4 CP2210 Setup Guide 020-100524-04 Rev. 1 (05-2014)
  • Page 9 7.19 The Display is Unstable......................7-5 7.20 The Display is Faint........................7-5 7.21 Portions of the Display are Cut OFF or Warped to the Opposite Edge........7-5 7.22 Display Appears Compressed (Vertically Stretched) ...............7-5 7.23 Inconsistent Picture Quality.......................7-5 CP2210 Setup Guide 020-100524-04 Rev. 1 (05-2014)

  • Page 11: Cinema Projector Labels And Marking

    1 Introduction This manual is intended for professionally trained operators of Christie high-brightness projection systems. These operators are qualified to replace the lamp and air filter, but should not attempt to install or service the cinema projector. Only accredited Christie technicians who are knowledgeable about the hazards associated with high-voltage, ultraviolet exposure, and the high temperatures generated by the cinema projector lamp are authorized to assemble, install, and service the cinema projector.

  • Page 12: Ac/Power Precautions

    Any lamp used in the CP2210 is under high pressure and must be handled with great care at all times. Lamps may explode if dropped or mishandled.

  • Page 13: Contact Your Dealer

    6-4. Contact Your Dealer If you encounter a problem with your Christie cinema projector, contact your dealer. Typically, servicing is performed on site. To assist with the servicing of your cinema projector, enter the information in the tables and keep this information with your records.

  • Page 15: 2: Installation And Setup

    2 Installation and Setup This section provides information and procedures for positioning and installing the cinema projector. You need these tools to install the CP2210 cinema projector: • 19 mm wrench • Protective safety clothing (if you are replacing the lamp) •...

  • Page 16: Adjustable Feet

    D cable that connects to the Auxiliary Input Panel. 2.3.7 Projection Lens A variety of lenses can be used with the CP2210. 2.3.8 Security Locks Critical internal components and/or connections are protected by various security locks on cinema projector covers/access panels.
  • Page 17 Installation and Setup • GPIO: Connect external I/O devices, such as the Christie ACT, for remote control of a limited number of cinema projector functions. See Section 3 Connect Devices to the cinema projector for GPIO pinouts. • SCCI: A Simple Contact Closure Interface (SCCI) port that provides the following functions upon a simple dry contact closure: Lamp ON/OFF and Douser Open/Closed.

  • Page 18: Touch Panel Controller (Tpc)

    TPC access up to 100 feet away. NOTE: If your system has a TPC-660E check to ensure the main switch on the back is connected properly. If your system has a TCP-650H it automatically turns ON when connected. CP2210 Setup Guide 020-100524-04 Rev. 1 (05-2014)

  • Page 19: Position The Cinema Projector

    2) The rack stand’s feet are used for leveling only and not for tilting the cinema projector. To prevent tipping ensure the required accessories supplied by Christie are used. 2. Position the cinema projector at an appropriate throw distance (cinema projector-to-screen distance) and vertical position.

  • Page 20: Adjust Tilt And Level The Cinema Projector

    Disconnect the cinema projector from AC when adjusting the tilt angle or leveling the cinema projector. The CP2210 lens should be centered and parallel with the screen. This orientation ensures optimum lens performance with minimal offset. If this position is not possible (such as when the cinema projector is significantly higher than the center of the screen), it is better to rely on offset rather than extra tilt.

  • Page 21: Connect Optional Exhaust Ducting

    Take the measurement at the very end of the duct without the cinema projector connected. Use this formula to determine the CFM value for the cinema projector: Measured linear ft/min x 0.34 = CFM Install the Primary Lens CP2210 Setup Guide 020-100524-04 Rev. 1 (05-2014)

  • Page 22: Install The Optional Anamorphic Lens

    5. Secure the two hex screws and position the lens clamp DOWN to lock the lens assembly in place. Figure 2-6 Lock Lens in Place Install the Optional Anamorphic Lens CP2210 Setup Guide 020-100524-04 Rev. 1 (05-2014)

  • Page 23: Install The Optional Wide Converter Lens

    Figure 2-7 MALM 2.12 Install the Lamp DANGER • Only personnel trained specifically by Christie on lamp replacement and lamp safety may handle the lamp. High-pressure lamp may explode if improperly handled. CP2210 Setup Guide 020-100524-04 Rev. 1 (05-2014)

  • Page 24: Connect The Cinema Projector To Ac Power

    Installation and Setup • Always wear Christie approved protective safety clothing (P/N: 59-8900-095) whenever the internal lamp door is open or while handling the lamp. • Never attempt to access the lamp while the lamp is ON. Wait at least 15 minutes after the lamp turns OFF before powering down, disconnecting from AC and opening the internal lamp door.

  • Page 25: Connect Sources And Turn The Cinema Projector On

    5. On the TPC, tap and hold the light bulb icon to ignite the lamp. 6. Complete an optical alignment to optimize images displayed on screen. See Section 4.3 Basic Image Alignment. 7. Adjust optical components if required. CP2210 Setup Guide 2-11 020-100524-04 Rev. 1 (05-2014)

  • Page 27: 3: Connect Devices To The Cinema Projector

    Cinema servers reside outside the cinema projector and are connected to one of the ports on the cinema Projector Intelligence Board (PIB) located on the left (operator’s) side of the cinema projector. (Figure 3-1) Figure 3-1 Connecting Cinema Sources CP2210 Setup Guide 020-100524-04 Rev. 1 (05-2014)

  • Page 28: Connect A Communications Device

    Connect Devices to the cinema projector Connect a Communications Device The RS232 PIB port located on the PIB faceplate utilizes Christie-proprietary protocol and is intended for Christie accessories or automation controllers only. To communicate with the cinema projector, connect the equipment to an Ethernet hub or switch.

  • Page 29: Connect Devices To The Gpio Port

    To configure the pins on the connector, tap Menu > Administrator Setup > GPIO Setup. Pin 1 Pin 37 GPIO Connector Figure 3-3 Admin: GPIO Setup Window and GPIO Port Location on cinema projector CP2210 Setup Guide 020-100524-04 Rev. 1 (05-2014)
  • Page 30 Max. Current = 50 mA Forward Voltage Drop ~ 1.1 V (@ 5 mA) +5 VDC (External Supply) To Center Pin of BNC To Shielding of BNC IR Emitter Figure 3-4 GPIO Circuit Diagram CP2210 Setup Guide 020-100524-04 Rev. 1 (05-2014)

  • Page 31: Connect Devices To The 3D Connector

    GPIO requirements and restrictions. (24VDC max, 50mA max) CONN_SYNC- SYNC from cinema projector. From cinema projector GPO emitter. Compatible with current cinema projector GPIO requirements and restrictions. (24DC max, 50mA max) Not connected CP2210 Setup Guide 020-100524-04 Rev. 1 (05-2014)

  • Page 33: 4: Adjust The Image

    2. Tap Do Auto. Calibrate Screen Brightness (fL) 1. On the Touch Pad Controller, tap Menu > Administrator Setup > Foot Lamberts Calibration. 2. Complete t he Foot Lamberts Calibration wizard. Figure 4-1 Footlamberts Calibration Wizard CP2210 Setup Guide 020-100524-04 Rev. 1 (05-2014)

  • Page 34: Basic Image Alignment

    This procedure ensures that the image reflected from the digital micromirror device (DMD) is parallel and centered with the lens and screen. This procedure must be completed before you complete a boresight adjustment. 1. Verify the CP2210 is properly positioned relative to the screen. See 2.4 Position the Cinema Projector.

  • Page 35: Adjust Horizontal Boresight

    (i.e. factory setup of absolute lens distance to the prism). It is critical that you count each turn of the cap screws to ensure accurate adjustment. Horizontal boresight should only be adjusted if a large horizontal tilt to the screen is required CP2210 Setup Guide 020-100524-04 Rev. 1 (05-2014)
  • Page 36 Only adjust vertical boresight 1/8 of a turn or less at one time to maintain optimal lens performance (i.e. factory setup of absolute lens distance to the prism). It is critical that each turn of the cap screws is tracked to ensure adjustments are accurate. CP2210 Setup Guide 020-100524-04 Rev. 1 (05-2014)

  • Page 37: Adjust Dmd Convergence

    Normally, the three colors should overlap precisely to form pure white lines throughout the image and one or more poorly converged individual colors may appear adjacent to some or all of the lines. Contact your Christie accredited service technician to correct DMD convergence issues.

  • Page 38: Electronic Screen Masking

    To learn more about accessing channels, see Channel Setup: Config 1 Window. To learn more about creating screen files, see Advanced Setup: Screen File Setup Window. CP2210 Setup Guide 020-100524-04 Rev. 1 (05-2014)

  • Page 39: Turn The Cinema Projector On

    5 Operation This section describes how to operate the CP2210 cinema projector. Turn the Cinema Projector On DO NOT attempt to turn the cinema projector on if the AC supply is not within the specified voltage range. 1. Ensure the circuit breaker for the cinema projector is ON.

  • Page 41: Inspect Ventilation

    Top up the coolant with the Christie approved coolant JEFFCOOL E105. Use the refill bottle (with the nozzle) provided in the Liquid Coolant Fill Service Kit (P/N: 003-001837-xx). When refilling, use caution not to spill or let any of the coolant drip on or near the electronics.

  • Page 42: Inspect The Lamp

    2. Wrap a lens tissue around a swab and soak it in lens cleaning solution. The tissue should be damp but not dripping. 3. Gently wipe the surface using a figure eight motion. Repeat until the blemish is removed. CP2210 Setup Guide 020-100524-04 Rev. 1 (05-2014)

  • Page 43: Clean The Lamp Reflector

    Wash the radiator filter with water and a mild detergent or clean it with compressed air. d. Ensure the air filter is completely dry and insert it with the air flow indicator facing toward the cinema projector. 4. Reinstall the service door and the top lid. CP2210 Setup Guide 020-100524-04 Rev. 1 (05-2014)

  • Page 44: Inspect And Clean Lamp Blower

    HAZARD. Wear authorized protective clothing whenever the lamp door is open and when handling the lamp. Never twist or bend the quartz lamp body. Use the correct wattage lamp supplied by Christie. 3) Ensure those within the vicinity of the cinema projector are also wearing protective safety clothing. 4) Never attempt to remove the lamp when it is hot.
  • Page 45 9. Close the internal lamp door and manually turn the 2 thumbscrews to lock it in place. 10. Close the rear access door. NOTE: Ensure the hex key is placed back into its holder before closing the rear access door. CP2210 Setup Guide 020-100524-04 Rev. 1 (05-2014)

  • Page 46: Rotate The Lamp

    Never twist or bend the quartz lamp body. Use the correct wattage lamp supplied by Christie. 3) Ensure those within the vicinity of the cinema projector are also wearing protective safety clothing. 4) Never attempt to remove the lamp when it is hot.

  • Page 47: Replace The Air Filter

    Maintenance 6.10 Replace the Air Filter Use only high efficiency Christie approved filters. Never operate the cinema projector without the filter installed. Always discard used air filters. You should check the condition of the light engine air filter monthly. Replace the light engine air filter when you replace the lamp module or sooner if you are operating the cinema projector in a dusty or dirty environment.

  • Page 48: Replace The Lens

    Once the lens makes contact with the magnetic plates it will be seated correctly and the connector for motorized zoom and focus will be properly connected (Figure 6-7). 9. Secure the lens clamp by pushing it down to the closed position. CP2210 Setup Guide 020-100524-04 Rev. 1 (05-2014)
  • Page 49 10. For added stability, secure the cap screws provided on the lens mount. If you have installed a large zoom lens, one or more of the screws may be inaccessible - simply tighten those that are accessible. NOTE: Recommended for heaviest lenses, such as 0.8:1 and 1.3-1.75:1. Figure 6-7 Install Lens CP2210 Setup Guide 020-100524-04 Rev. 1 (05-2014)

  • Page 51: Cinema Projector Does Not Turn On

    • Listen for a clicking noise that indicates the ballast is attempting to strike the lamp. If you do not hear a clicking noise, there might be a problem a problem with the ballast. Contact a Christie accredited service technician to resolve the issue.

  • Page 52: Lamp Suddenly Turns Off

    Increase the lamp power. Lamps which are near end of service may not operate reliably at a lower power setting. • Fold mirror misalignment. Contact your Christie accredited service technician to resolve the issue. • Integrator rod misalignment. Contact your Christie accredited service technician to resolve the issue.

  • Page 53: Cannot Establish Communication With Cinema Projector

    Setup. Tap Config 1 in the left pane and verify the correct value is selected in the PCF list. Tap Config 2 in the left pane and verify the correct value is selected in the Color Space field. CP2210 Setup Guide 020-100524-04 Rev. 1 (05-2014)

  • Page 54: Display Is Not Rectangular

    • Ensure an active source is connected properly. Check the cable connections and make sure the alternative source is selected. • Verify you can select test patterns. If you can, check your source connections again. • Ensure your Cinema server is running Series 2 compatible software. CP2210 Setup Guide 020-100524-04 Rev. 1 (05-2014)

  • Page 55: The Display Is Unstable

    • Use an anamorphic lens for HDTV and anamorphic DVD input sources that have been re-sized and verti- cally stretched. 7.23 Inconsistent Picture Quality • Verify the quality of the signal from the input source. • Verify the H and V frequencies of the input source are correct. CP2210 Setup Guide 020-100524-04 Rev. 1 (05-2014)
  • Page 58 Corporate offi ces Worldwide offi ces USA – Cypress United Kingdom Eastern Europe Singapore Japan ph: 714-236-8610 ph: +44 118 977 8000 ph: +36 (0) 1 47 48 100 ph: +65 6877-8737 ph: 81-3-3599-7481 Canada – Kitchener France Middle East Beijing South Korea ph: 519-744-8005...

Table of Contents