On Screen Messages - Sony PCS-1500 Service Manual

Location and Function of Parts and Controls
!¶ INPUT SELECT buttons @£ MENU button
Selects the input. Displays the Menu (System
MAIN: Selects the camera of the Configuration Index 1/3) menu on the
Compact Processor. monitor screen.
OBJECT: Selects the infrared video
@¢ I/u button
input via the IR sensor.
VIDEO/TV: Selects the video input. Press this button to turn into standby
AUDIO: Selects the audio input. when the system is turned on; to turn
on the system when the system is on
!• FAR/NEAR button
standby.
Selects the camera to be adjusted.
!ª CAMERA buttons
To operate a Sony TV
Operates the camera.
monitor
PRESET: Used to preset the camera
adjustment settings.
Note
AUTO TRACK: Displays the Auto
When you operate a Sony TV, set the
Tracking menu.
CONF/DOC/TV selector to "TV."
A–F: Used to preset or recall the
setting.
9 VOLUME/BRIGHT (+/–)
buttons
@º EDIT buttons
These buttons adjust the volume.
ALPHA/NUM: Switches the
character input mode.
SYMBOL: Enters special
characters.
!™ ZOOM/CH (T+/W–) buttons
CLEAR: Deletes an entry.
These buttons select the channel of the
BACK SPACE: Deletes the last
TV monitor.
input character.
@¡ DISPLAY buttons
MULTI/AUTO: Displays the Chair
!¶ INPUT SELECT button
Control menu.
Selects the input of the TV monitor.
VIEW SEL: Selects the terminal to
be displayed .
FAR/NEAR: Switches the picture
between local and remote.
@¢ I/u button
PinP: Displays the inset window.
Turns on/off the TV monitor when
using an NTSC type TV monitor.
@™ PIX SHOT buttons
Turns off the TV monitor when using
SNAP: Sends one still picture.
a PAL type TV monitor.
AUTO: Sends still pictures
continuously.
94
Appendix
+: press to increase the volume.
–: press to decrease the volume.
T+: Tunes to the upper channel.
W–: Tunes to the lower channel.
VIDEO/TV: Switches the input of
the TV monitor.

On Screen Messages

The following messages appear on the TV monitor when using
the Compact Processor and gives instructions on dealing with
them.
Message Remedy
INCORRECT DIALING SETUP
Make sure the selected entry is correctly
registered.
CANNOT COMPLETE CONNECTION
(The following code and message
appear.)
0 Unknown network error: Please try again later.
1 Number does not exist: Please check the number and try again.
2,3,6 Network congestion: Please try again later.
16 Normal disconnection: (Normal disconnect)
17 Line is busy:
Please try again later.
18 System not responding: Please check if remote system is connected.
19 No answer from user: Please check if other party is present.
21 Call rejected by network: Please check access restrictions remote site.
22 Called party number changed:
Please check the number and try again.
26 Non-selected user clearing: Please try again later.
27 Remote system out of order: Please contact remote party.
28 Invalid number entered: Please check the number and try again.
31, 34, 41 – 44, 47 Please try again later.
Network not available:
50 Not Subscribed:
Please check the remote party's facility
subscription.
57,58 Bearer capability not Check if the line rate is set correctly.
authorized:
70 Line Rate Error: Please check if the line rate is set to correctly.
88 Incompatible equipment on Please check if remote party has compatible
remote site: system.
91, 95 – 102, 111 Restart system and try again.
Local system out of order:
131 Hardware failure. Check the line interface boards.
132 SPID registration incompatible: Please reregister SPID.
128 H.221 Negotiation timeout: Power off and power on.
144 Bonding Negotiation timeout: Power off and power on.
145 Bonding Negotiation failed: Power off and power on.
95
Appendix